Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM2090E _58 Vehicle Interior _060699 METER / GAUGE / DISPLAY _0297701 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1509  Open in Ambient Temperature Sensor Circuit  


DESCRIPTION

The thermistor assembly is installed in the front part of the cooler condenser assembly to display the ambient temperature on the multi-information display in the combination meter assembly and to control the air conditioning auto mode. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The combination meter assembly applies a voltage (5 V) to the thermistor assembly and reads the voltage changes as changes in the resistance of the thermistor assembly.

DTC No. DTC Detection Condition Trouble Area
B1509 An open or short in the thermistor assembly circuit.
·

Thermistor assembly

·

Harness or connector

·

Combination meter assembly



WIRING DIAGRAM

E185871E05
0.625,2.177 2.313,2.375 1.688,0.198 10 false THERMISTOR ASSEMBLY 2.229,1.01 2.333,1.177 0.104,0.167 10 false 1 2.24,1.396 2.344,1.563 0.104,0.167 10 false 2 4.99,1.396 5.604,1.573 0.615,0.177 10 false 25 4.99,1 5.531,1.177 0.542,0.177 10 false 24 4.615,2.323 7.073,2.51 2.458,0.188 10 false COMBINATION METER ASSEMBLY 4.625,2.156 5.615,2.323 0.99,0.167 10 false D7 5.26,1.104 5.906,1.333 0.646,0.229 10 false TAM 5.26,1.5 5.969,1.75 0.708,0.25 10 false SG- 0.635,2 1.458,2.219 0.823,0.219 10 false A48

PROCEDURE

1.READ VALUE USING GTS (AMBIENT TEMPERATURE SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

According to the display on the GTS, read the Data List.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Ambient Temperature Thermistor assembly /
Min: -40.0°C (-40.0°F)
Max: 87.5°C (189.5°F)
Actual ambient temperature displayed Open in the circuit: -40.0°C (-40.0°F)
Short in the circuit: 87.5°C (189.5°F)

OK:

The display is as specified in the normal condition column.


Result
Result Proceed to
OK (When troubleshooting according to the DTC) A
OK (When troubleshooting according to problem symptoms table) B
NG C



A

2.CHECK FOR DTC

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

C

3.INSPECT THERMISTOR ASSEMBLY
2.CHECK FOR DTC

OK

END

NG

REPLACE COMBINATION METER ASSEMBLY

3.INSPECT THERMISTOR ASSEMBLY

OK

4.CHECK HARNESS AND CONNECTOR (THERMISTOR ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (THERMISTOR ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the A48 thermistor assembly connector.


b.

Disconnect the D7 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A48-1 - D7-24 (TAM) Always Below 1 Ω
A48-2 - D7-25 (SG-) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A48-1 - Body ground Always 10 kΩ or higher
A48-2 - Body ground Always 10 kΩ or higher




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR