Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2012.03–2019.03
RM2090E _58 Vehicle Interior _060701 SUPPLEMENTAL RESTRAINT SYSTEMS _0297704 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  SRS Warning Light does not Come ON  


DESCRIPTION

The SRS warning light is located on the combination meter assembly.

When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from off to ON, and then goes off automatically.

If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.

The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the airbag ECU assembly in case the source voltage drops.

When the battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage.

A malfunction in this circuit is not stored in the airbag ECU assembly. The SRS warning light automatically goes off when the source voltage returns to normal.

The signal to illuminate the SRS warning light is transmitted from the airbag ECU assembly to the combination meter assembly through the CAN communication system.

WIRING DIAGRAM

C260972E02
0.75,4.375 2.417,4.573 1.667,0.198 10 false :CAN Communication Line 2.688,3.792 4.542,4 1.854,0.208 10 false Combination Meter Assembly 5.708,3.823 7.083,4.073 1.375,0.25 10 false Airbag ECU Assembly 2.698,3.615 2.906,3.792 0.208,0.177 10 false D7 5.719,3.646 6.042,3.813 0.323,0.167 10 false D27 5.792,2.271 6.073,2.51 0.281,0.24 10 false 25 5.792,2.781 6.073,3.031 0.281,0.25 10 false 26 5.792,1.135 6.104,1.365 0.313,0.229 10 false 13 5.792,1.677 6.104,1.938 0.313,0.26 10 false 22 5.792,0.344 6.146,0.646 0.354,0.302 10 false 21 4.104,1.135 4.396,1.375 0.292,0.24 10 false 6 4.104,1.677 4.365,1.885 0.26,0.208 10 false 7 2.948,1.167 3.188,1.406 0.24,0.24 10 false 2 2.875,2.292 3.156,2.552 0.281,0.26 10 false 20 2.875,2.677 3.156,2.948 0.281,0.271 10 false 40 2.948,1.74 3.177,1.99 0.229,0.25 10 false 1 2.24,1.99 2.844,2.25 0.604,0.26 10 false MPX-B 2.25,1.417 2.781,1.656 0.531,0.24 10 false GAUGE 0.698,1.813 1.479,2 0.781,0.188 10 false from Battery 0.51,0.448 1.448,0.625 0.938,0.177 10 false from IG2 Relay 4.979,0.604 5.76,0.844 0.781,0.24 10 false A/B MAIN 4.052,0.604 4.531,0.802 0.479,0.198 10 false IG2 6.063,0.469 6.469,0.75 0.406,0.281 10 false IG 6.063,1.281 6.625,1.531 0.563,0.25 10 false CANH 6.063,1.833 6.521,2.052 0.458,0.219 10 false CANL 3.635,1.281 4.125,1.521 0.49,0.24 10 false CANH 3.646,1.833 4.135,2.083 0.49,0.25 10 false CANL 6.063,2.396 6.469,2.625 0.406,0.229 10 false GND 6.063,2.906 6.49,3.125 0.427,0.219 10 false GND 3.135,1.281 3.469,1.479 0.333,0.198 10 false IG+ 3.135,1.833 3.365,1.979 0.229,0.146 10 false B 3.135,2.354 3.51,2.583 0.375,0.229 10 false ES1 3.135,2.771 3.542,3.073 0.406,0.302 10 false ES2

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK BATTERY VOLTAGE
a.

Measure the voltage of the battery.

Standard Voltage:

11 to 14 V




OK

2.CHECK CONNECTOR

NG

2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connector is properly connected to the combination meter assembly.

OK:

The connector is properly connected.


HINT:

If the connector is not connected securely, reconnect the connector and proceed to the next inspection.



d.

Disconnect the connector from the combination meter assembly.


e.

Check that the terminal of the connector is not damaged.

OK:

The terminal is not deformed or damaged.




OK

3.CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE CONNECTOR

3.CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - BODY GROUND)
a.
U147149E02
0.438,0.615 0.573,1.104 true 0.438,1.208 0.26,1.646 true 2.938,1.219 2.427,1.833 true 2.958,1.396 2.854,1.729 true 1.615,0.302 1.813,0.458 0.198,0.156 10 false D7 0.094,0.094 0.24,0.229 0.146,0.135 10 false *a 0.156,1.656 0.323,1.885 0.167,0.229 10 false B 0.198,0.521 0.438,0.781 0.24,0.26 10 false IG+ 2.135,1.792 2.438,1.99 0.302,0.198 10 false ES1 2.698,1.76 2.99,1.906 0.292,0.146 10 false ES2

Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D7-1 (B) - Body ground Always 11 to 14 V
D7-2 (IG+) - Body ground Ignition switch ON 11 to 14 V



d.

Turn the ignition switch off.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D7-20 (ES1) - Body ground Always Below 1 Ω
D7-40 (ES2) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)



OK

4.CHECK SRS WARNING LIGHT

NG

REPAIR OR REPLACE WIRE HARNESS

4.CHECK SRS WARNING LIGHT
a.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



b.

Connect the connector to the combination meter assembly.


c.

Disconnect the connector from the airbag ECU assembly.


d.

Connect the cable to the negative (-) battery terminal.


e.

Turn the ignition switch to ON.


f.

Check the SRS warning light condition.

OK:

After the primary check period, the SRS warning light goes off for approximately 10 seconds and turns back on.


HINT:

The primary check period is approximately 6 seconds after the ignition switch is turned to ON.




OK

NG

REPLACE COMBINATION METER ASSEMBLY