Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM2090E _58 Vehicle Interior _060701 SUPPLEMENTAL RESTRAINT SYSTEMS _0297704 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  Trouble in Passenger Airbag ON/OFF Indicator  


DESCRIPTION

This circuit detects the airbag cut off switch status.

The passenger airbag ON/OFF indicator comes on to inform the front passenger airbag status (activated or deactivated).

HINT:

Approximately 6 seconds after the ignition switch is turned ON, the passenger airbag ON/OFF indicator will indicate ON/OFF depending on the conditions listed below.

Airbag Cut Off Switch Passenger Airbag ON/OFF Indicator SRS Warning Light
ON Indicator OFF Indicator
ON position ON OFF OFF
OFF position OFF ON OFF
Switch failure OFF ON ON


WIRING DIAGRAM

C263719E01
0.571,3.707 1.917,3.864 1.346,0.157 10 Airbag Cut Off Switch 5.313,3.734 5.593,3.891 0.280,0.157 10 D27 5.313,3.888 6.709,4.028 1.395,0.140 10 Airbag ECU Assembly 5.626,1.379 6.073,1.527 0.448,0.149 10 MSW+ 5.357,1.269 5.536,1.427 0.179,0.158 10 14 5.626,2.871 6.044,3.020 0.419,0.149 10 MSW- 2.328,1.269 2.765,1.418 0.437,0.149 10 MSW+ 2.361,2.761 2.766,2.910 0.405,0.149 10 MSW- 5.357,2.761 5.536,2.919 0.179,0.158 10 12 2.884,1.269 2.982,1.427 0.098,0.158 10 2 2.884,2.761 2.982,2.919 0.098,0.158 10 1 0.57,3.538 0.925,3.727 0.355,0.188 10 D37

CAUTION / NOTICE / HINT

HINT:

Terminals D27-14 (MSW+) and D27-12 (MSW-) of the airbag ECU assembly in this circuit have an activation prevention mechanism.

This mechanism can be used to check for an open circuit in the wire harness. In case of other checks (check for short, short to ground or short to B+), this mechanism should be released.


PROCEDURE

1.CHECK SRS WARNING LIGHT
a.

Turn the ignition switch ON, and check the SRS warning light condition.

HINT:

If this trouble occurs, the SRS warning light is off. If it is on, a DTC is stored. Troubleshoot for the stored DTC.


OK:

After the primary check period, the SRS warning light goes off.


HINT:

The primary check period is approximately 6 seconds after the ignition switch is turned ON.




OK

2.CHECK CONNECTORS

NG

2.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag ECU assembly and airbag cut off switch.

OK:

The connectors are properly connected.


HINT:

If the connector is not connected securely, reconnect the connector and proceed to the next inspection.



d.

Disconnect the connectors from the airbag ECU assembly and airbag cut off switch.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the short spring for the instrument panel wire connector with the activation prevention mechanism is not deformed or damaged.

OK:

The short spring is not deformed or damaged.




OK

3.CHECK INSTRUMENT PANEL WIRE (OPEN)

NG

REPLACE INSTRUMENT PANEL WIRE

3.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.

Using a service wire, connect terminals 12 (MSW-) and 14 (MSW+) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.
U190382E02
1.927,0.781 1.594,1.24 true 2.104,0.781 2.438,1.24 true 1.698,2.646 1.552,2.646 1.552,2.646 1.552,2.292 false 1.458,4.219 1.625,3.917 true 1.875,3.917 2.01,4.219 true 1.198,0.667 1.469,0.823 0.271,0.156 10 false D27 0.875,3.698 1.146,3.854 0.271,0.156 10 false D37 2.49,1.177 2.99,1.385 0.5,0.208 10 false MSW+ 1.135,1.177 1.604,1.417 0.469,0.24 10 false MSW- 2.052,4.146 2.49,4.354 0.438,0.208 10 false MSW+ 1.021,4.146 1.458,4.365 0.438,0.219 10 false MSW- 0.885,0.208 1.042,0.354 0.156,0.146 10 false *a 0.26,3.188 0.417,3.333 0.156,0.146 10 false *b 0.635,2.135 0.781,2.281 0.146,0.146 10 false *1 2.469,2.427 2.615,2.573 0.146,0.146 10 false *2 2.063,2.146 2.177,2.292 0.115,0.146 10 false A 1.719,2.146 1.833,2.292 0.115,0.146 10 false B 1.271,2.146 1.385,2.292 0.115,0.146 10 false C 0.938,2.146 1.052,2.292 0.115,0.146 10 false D 1.719,2.563 1.865,2.708 0.146,0.146 10 false *3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D37-2 (MSW+) - D37-1 (MSW-) Always Below 1 Ω


Text in Illustration
*1 Airbag Cut Off Switch
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Airbag Cut Off Switch)



OK

4.CHECK INSTRUMENT PANEL WIRE (SHORT)

NG

REPLACE INSTRUMENT PANEL WIRE

4.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.
U190383E02
1.656,1.198 1.51,1.198 1.51,1.198 1.51,0.781 false 1.781,2.802 1.927,2.479 true 2.208,2.479 2.292,2.802 true 0.51,1.719 0.667,1.865 0.156,0.146 10 false *a 0.615,0.625 0.76,0.771 0.146,0.146 10 false *1 2.448,0.906 2.594,1.052 0.146,0.146 10 false *2 1.677,1.125 1.823,1.271 0.146,0.146 10 false *3 1.208,2.24 1.479,2.396 0.271,0.156 10 false D37 2.042,0.625 2.167,0.792 0.125,0.167 10 false A 1.698,0.625 1.833,0.833 0.135,0.208 10 false B 1.26,0.625 1.396,0.823 0.135,0.198 10 false C 0.917,0.625 1.052,0.813 0.135,0.188 10 false D 1.323,2.729 1.74,2.938 0.417,0.208 10 false MSW- 2.344,2.729 2.802,2.979 0.458,0.25 10 false MSW+

Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D37-2 (MSW+) - D37-1 (MSW-) Always 1 MΩ or higher


Text in Illustration
*1 Airbag Cut Off Switch
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Airbag Cut Off Switch)



OK

5.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)

NG

REPLACE INSTRUMENT PANEL WIRE

5.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
U190383E02
1.656,1.198 1.51,1.198 1.51,1.198 1.51,0.781 false 1.781,2.802 1.927,2.479 true 2.208,2.479 2.292,2.802 true 0.51,1.719 0.667,1.865 0.156,0.146 10 false *a 0.615,0.625 0.76,0.771 0.146,0.146 10 false *1 2.448,0.906 2.594,1.052 0.146,0.146 10 false *2 1.677,1.125 1.823,1.271 0.146,0.146 10 false *3 1.208,2.24 1.479,2.396 0.271,0.156 10 false D37 2.042,0.625 2.167,0.792 0.125,0.167 10 false A 1.698,0.625 1.833,0.833 0.135,0.208 10 false B 1.26,0.625 1.396,0.823 0.135,0.198 10 false C 0.917,0.625 1.052,0.813 0.135,0.188 10 false D 1.323,2.729 1.74,2.938 0.417,0.208 10 false MSW- 2.344,2.729 2.802,2.979 0.458,0.25 10 false MSW+

Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D37-1 (MSW-) - Body ground Ignition switch ON Below 1 V
D37-2 (MSW+) - Body ground Ignition switch ON Below 1 V



Text in Illustration
*1 Airbag Cut Off Switch
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Airbag Cut Off Switch)


OK

6.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)

NG

REPLACE INSTRUMENT PANEL WIRE

6.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
U190383E02
1.656,1.198 1.51,1.198 1.51,1.198 1.51,0.781 false 1.781,2.802 1.927,2.479 true 2.208,2.479 2.292,2.802 true 0.51,1.719 0.667,1.865 0.156,0.146 10 false *a 0.615,0.625 0.76,0.771 0.146,0.146 10 false *1 2.448,0.906 2.594,1.052 0.146,0.146 10 false *2 1.677,1.125 1.823,1.271 0.146,0.146 10 false *3 1.208,2.24 1.479,2.396 0.271,0.156 10 false D37 2.042,0.625 2.167,0.792 0.125,0.167 10 false A 1.698,0.625 1.833,0.833 0.135,0.208 10 false B 1.26,0.625 1.396,0.823 0.135,0.198 10 false C 0.917,0.625 1.052,0.813 0.135,0.188 10 false D 1.323,2.729 1.74,2.938 0.417,0.208 10 false MSW- 2.344,2.729 2.802,2.979 0.458,0.25 10 false MSW+

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
D37-1 (MSW-) - Body ground Always 1 MΩ or higher
D37-2 (MSW+) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Airbag Cut Off Switch
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Airbag Cut Off Switch)



OK

7.CHECK AIRBAG CUT OFF SWITCH

NG

REPLACE INSTRUMENT PANEL WIRE

7.CHECK AIRBAG CUT OFF SWITCH
a.
B311951E01
0.144,0.114 0.330,0.275 0.186,0.161 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (MSW+) - 1 (MSW-) Cut off switch in ON 100 Ω
Cut off switch in OFF 400 Ω


Text in Illustration
*a Component without harness connected
(Airbag Cut Off Switch)



OK

NG