Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM2090E _58 Vehicle Interior _060701 SUPPLEMENTAL RESTRAINT SYSTEMS _0297704 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1678  Lost Communication with Rear Floor Airbag Sensor LH  B1679  Rear Floor Airbag Sensor LH Initialization Incomplete  


DESCRIPTION

The No. 2 airbag sensor assembly circuit consists of the airbag ECU assembly and No. 2 airbag sensor assembly.

The No. 2 airbag sensor assembly detects impacts to the vehicle and sends signals to the airbag ECU assembly to determine if the airbag should be deployed.

These DTCs are stored when a malfunction is detected in the No. 2 airbag sensor assembly circuit.


DTC Code DTC Detection Condition Trouble Area
B1678
B1679
·

The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the No. 2 airbag sensor assembly circuit.

·

No. 2 airbag sensor assembly malfunction.

·

Airbag ECU assembly malfunction.


·

Floor wire

·

No. 2 airbag sensor assembly

·

Airbag ECU assembly



WIRING DIAGRAM

C259335E02
5.323,3.802 5.656,3.969 0.333,0.167 10 false H17 0.25,3.802 0.656,4.031 0.406,0.229 10 false H16 5.396,1.271 5.646,1.49 0.25,0.219 10 false 11 5.396,2.615 5.708,2.823 0.313,0.208 10 false 12 1.677,1.271 1.958,1.531 0.281,0.26 10 false 2 1.677,2.615 1.938,2.823 0.26,0.208 10 false 1 5.313,3.969 6.75,4.167 1.438,0.198 10 false Airbag ECU Assembly 0.229,3.948 2.156,4.146 1.927,0.198 10 false No. 2 Airbag Sensor Assembly 5.646,1.365 6.198,1.615 0.552,0.25 10 false BBL2+ 5.646,2.708 6.188,2.927 0.542,0.219 10 false BBL2- 1.188,1.365 1.708,1.604 0.521,0.24 10 false BBL2+ 1.188,2.708 1.698,2.927 0.51,0.219 10 false BBL2-

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag ECU assembly and No. 2 airbag sensor assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag ECU assembly and No. 2 airbag sensor assembly.


e.

Check that the terminals of connectors are not damaged.

OK:

The connectors are not deformed or damaged.




OK

2.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

2.CHECK FLOOR WIRE (OPEN)
a.
U147184E04
1.792,0.917 1.594,0.385 true 1.906,0.917 2.313,0.667 true 2.01,1.375 2.25,1.375 false 1.771,2.781 1.594,2.781 1.594,2.781 1.594,2.448 false 0.969,4.333 1.229,3.854 true 1.479,3.854 1.646,4.333 true 0.844,0.24 1.042,0.51 0.198,0.271 10 false *a 0.719,2.281 0.885,2.521 0.167,0.24 10 false *1 2.49,2.271 2.74,2.573 0.25,0.302 10 false *2 2.281,1.292 2.49,1.542 0.208,0.25 10 false *4 1.792,2.698 1.958,2.938 0.167,0.24 10 false *3 0.396,3.208 0.615,3.5 0.219,0.292 10 false *b 2.365,0.583 2.802,0.729 0.438,0.146 10 false BBL2+ 1.698,4.26 2.188,4.479 0.49,0.219 10 false BBL2+ 1.167,0.281 1.573,0.427 0.406,0.146 10 false BBL2- 0.542,4.25 0.938,4.458 0.396,0.208 10 false BBL2- 2.083,2.292 2.219,2.5 0.135,0.208 10 false A 1.781,2.292 1.917,2.49 0.135,0.198 10 false B 1.323,2.292 1.479,2.479 0.156,0.188 10 false C 1.01,2.292 1.156,2.49 0.146,0.198 10 false D 1.177,0.708 1.448,0.865 0.271,0.156 10 false H17 0.521,3.74 0.792,3.896 0.271,0.156 10 false H16

Using a service wire, connect terminals 11 (BBL2+) and 12 (BBL2-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H16-1 (BBL2-) - H16-2 (BBL2+) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


Text in Illustration
*1 No. 2 Airbag Sensor Assembly
*2 Airbag ECU Assembly
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to No. 2 Airbag Sensor Assembly)


OK

3.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE (SHORT)
a.
U147094E02
1.594,1.042 1.594,0.375 1.594,0.375 1.771,0.375 false 1.021,3.063 1.229,2.615 true 1.479,2.615 1.677,3.063 true 0.719,1.031 0.865,1.167 0.146,0.135 10 false *1 2.49,1.031 2.698,1.281 0.208,0.25 10 false *2 1.792,0.292 1.99,0.542 0.198,0.25 10 false *3 0.406,1.99 0.615,2.25 0.208,0.26 10 false *a 0.521,2.479 0.792,2.635 0.271,0.156 10 false H16 2.094,1.042 2.208,1.177 0.115,0.135 10 false A 1.01,1.042 1.156,1.24 0.146,0.198 10 false D 1.323,1.042 1.448,1.26 0.125,0.219 10 false C 1.781,1.042 1.917,1.229 0.135,0.188 10 false B 0.573,2.99 1.01,3.188 0.438,0.198 10 false BBL2- 1.729,3.01 2.167,3.156 0.438,0.146 10 false BBL2+

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H16-1 (BBL2-) - H16-2 (BBL2+) Always 1 MΩ or higher



Text in Illustration
*1 No. 2 Airbag Sensor Assembly
*2 Airbag ECU Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to No. 2 Airbag Sensor Assembly)


OK

4.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

4.CHECK FLOOR WIRE (SHORT TO B+)
a.
U147094E02
1.594,1.042 1.594,0.375 1.594,0.375 1.771,0.375 false 1.021,3.063 1.229,2.615 true 1.479,2.615 1.677,3.063 true 0.719,1.031 0.865,1.167 0.146,0.135 10 false *1 2.49,1.031 2.698,1.281 0.208,0.25 10 false *2 1.792,0.292 1.99,0.542 0.198,0.25 10 false *3 0.406,1.99 0.615,2.25 0.208,0.26 10 false *a 0.521,2.479 0.792,2.635 0.271,0.156 10 false H16 2.094,1.042 2.208,1.177 0.115,0.135 10 false A 1.01,1.042 1.156,1.24 0.146,0.198 10 false D 1.323,1.042 1.448,1.26 0.125,0.219 10 false C 1.781,1.042 1.917,1.229 0.135,0.188 10 false B 0.573,2.99 1.01,3.188 0.438,0.198 10 false BBL2- 1.729,3.01 2.167,3.156 0.438,0.146 10 false BBL2+

Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H16-1 (BBL2-) - Body ground Ignition switch ON Below 1 V
H16-2 (BBL2+) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Text in Illustration
*1 No. 2 Airbag Sensor Assembly
*2 Airbag ECU Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to No. 2 Airbag Sensor Assembly)


OK

5.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

5.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
U147094E02
1.594,1.042 1.594,0.375 1.594,0.375 1.771,0.375 false 1.021,3.063 1.229,2.615 true 1.479,2.615 1.677,3.063 true 0.719,1.031 0.865,1.167 0.146,0.135 10 false *1 2.49,1.031 2.698,1.281 0.208,0.25 10 false *2 1.792,0.292 1.99,0.542 0.198,0.25 10 false *3 0.406,1.99 0.615,2.25 0.208,0.26 10 false *a 0.521,2.479 0.792,2.635 0.271,0.156 10 false H16 2.094,1.042 2.208,1.177 0.115,0.135 10 false A 1.01,1.042 1.156,1.24 0.146,0.198 10 false D 1.323,1.042 1.448,1.26 0.125,0.219 10 false C 1.781,1.042 1.917,1.229 0.135,0.188 10 false B 0.573,2.99 1.01,3.188 0.438,0.198 10 false BBL2- 1.729,3.01 2.167,3.156 0.438,0.146 10 false BBL2+

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H16-1 (BBL2-) - Body ground Always 1 MΩ or higher
H16-2 (BBL2+) - Body ground Always 1 MΩ or higher



Text in Illustration
*1 No. 2 Airbag Sensor Assembly
*2 Airbag ECU Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to No. 2 Airbag Sensor Assembly)


OK

6.CHECK NO. 2 AIRBAG SENSOR ASSEMBLY

NG

REPLACE FLOOR WIRE

6.CHECK NO. 2 AIRBAG SENSOR ASSEMBLY
a.
C238224E05
0.792,1.01 0.938,1.198 0.146,0.188 10 false *1 2.313,1.01 2.521,1.198 0.208,0.188 10 false *2 1.875,1.01 2,1.198 0.125,0.188 10 false A 1.708,1.01 1.833,1.198 0.125,0.188 10 false B 1.271,1.01 1.396,1.198 0.125,0.188 10 false C 1.115,1.01 1.24,1.198 0.125,0.188 10 false D

Connect the connectors to the No. 2 airbag sensor assembly and airbag ECU assembly.


b.

Replace the No. 2 airbag sensor assembly with a new one.


c.

Connect the cable to the negative (-) battery terminal.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

:
Result Proceed to
DTCs B1678 and B1679 are not output. A
DTC B1678 or B1679 is output. B


HINT:

Codes other than DTCs B1678 and B1679 may be output at this time, but they are not related to this check.



Text in Illustration
*1 No. 2 Airbag Sensor Assembly
*2 Airbag ECU Assembly


A

END (NO. 2 AIRBAG SENSOR ASSEMBLY WAS DEFECTIVE)

B