Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM2090E _58 Vehicle Interior _060701 SUPPLEMENTAL RESTRAINT SYSTEMS _0297704 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1622  Side Airbag Sensor RH Lost Communication  B1623  Side Airbag Sensor RH Initialization  B1632  Side No. 2 Airbag Sensor RH Lost Communication  B1633  Side No. 2 Airbag Sensor RH Initialization  B1642  Side Satellite Sensor Bus Lost Communication (RH)  B1692  Lost Communication with Side Airbag Sensor RH  B1693  Side Airbag Sensor RH Initialization Incomplete  


DESCRIPTION

The side collision sensor RH circuit (to determine deployment of the front seat airbag assembly RH, curtain shield airbag assembly RH and front seat outer belt assembly RH) is composed of the airbag ECU assembly, side airbag sensor assembly RH, side No. 2 airbag sensor assembly RH, rear airbag sensor RH and No. 2 airbag sensor assembly.

The side airbag sensor assembly RH, side No. 2 airbag sensor assembly RH and rear airbag sensor RH detect impacts to the vehicle and send signals to the airbag ECU assembly to determine if the airbag should be deployed.

These DTCs are stored when a malfunction is detected for the side collision sensor RH circuit.

DTC No. DTC Detection Condition Trouble Area
B1622
B1623
B1632
B1633
B1642
B1692
B1693
·

The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the side collision sensor RH circuit.


·

Side airbag sensor assembly RH malfunction

·

Side No. 2 airbag sensor assembly RH malfunction

·

Rear airbag sensor RH malfunction

·

Airbag ECU assembly malfunction


·

No. 2 floor wire

·

Front door wire RH

·

Side airbag sensor assembly RH

·

Side No. 2 airbag sensor assembly RH

·

Rear airbag sensor RH

·

Airbag ECU assembly



WIRING DIAGRAM

C238366E99
5.313,4.865 6.719,5.229 1.406,0.365 10 false Airbag ECU Assembly 0.521,2.854 2.104,3.281 1.583,0.427 10 false Side No. 2 Airbag Sensor Assembly RH 3.396,4.865 5.042,5.24 1.646,0.375 10 false Rear Airbag Sensor RH 0.531,4.865 2.792,5.188 2.26,0.323 10 false Side Airbag Sensor Assembly RH 5.396,0.427 5.656,0.688 0.26,0.26 10 false 8 5.333,1 5.635,1.229 0.302,0.229 10 false 11 1.604,0.448 1.813,0.688 0.208,0.24 10 false 4 1.604,1.021 1.813,1.24 0.208,0.219 10 false 3 1.604,1.604 1.781,1.802 0.177,0.198 10 false 1 1.604,2.198 1.76,2.385 0.156,0.188 10 false 2 3.302,1.594 3.51,1.844 0.208,0.25 10 false 4 3.302,2.198 3.531,2.438 0.229,0.24 10 false 3 3.302,3.698 3.542,3.969 0.24,0.271 10 false 1 2.354,3.802 2.698,4.01 0.344,0.208 10 false FG1 5.313,4.708 5.625,4.875 0.313,0.167 10 false G1 0.531,2.667 0.938,2.885 0.406,0.219 10 false G16 3.396,4.698 3.781,4.875 0.385,0.177 10 false G14 0.552,4.698 0.875,4.875 0.323,0.177 10 false F2 2.354,4.344 2.688,4.542 0.333,0.198 10 false FG1 3.302,4.24 3.49,4.438 0.188,0.198 10 false 2 1.594,3.688 1.781,3.875 0.188,0.188 10 false 2 1.594,4.229 1.74,4.417 0.146,0.188 10 false 1 2.438,3.594 2.615,3.771 0.177,0.177 10 false 2 2.438,4.115 2.646,4.292 0.208,0.177 10 false 1 5.583,0.531 6.052,0.74 0.469,0.208 10 false BBR+ 5.583,1.115 6.01,1.344 0.427,0.229 10 false BBR- 1.073,0.542 1.563,0.76 0.49,0.219 10 false BUSIN 1.094,1.125 1.604,1.333 0.51,0.208 10 false RTNIN 1.083,3.792 1.594,4.01 0.51,0.219 10 false BUSIN 1.104,4.344 1.583,4.542 0.479,0.198 10 false RTNIN 3.479,1.708 4.01,1.917 0.531,0.208 10 false BUSIN 3.5,2.292 4.083,2.479 0.583,0.188 10 false RTNIN 0.927,1.708 1.542,1.948 0.615,0.24 10 false BUSOUT 0.927,2.302 1.542,2.521 0.615,0.219 10 false RTNOUT 3.479,3.792 4.167,3.979 0.688,0.188 10 false BUSOUT 3.479,4.333 4.083,4.531 0.604,0.198 10 false RTNOUT

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK CURRENT DTC
a.

Check for current DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
Current DTC B1642 is output. A
Current DTC B1623 or B1633 is output. B
Current DTC B1692 or B1693 is output. C
Current DTC B1622 or B1632 is output. D
Current DTCs B1622, B1623, B1632, B1633, B1642, B1692 and B1693 are not output. E


HINT:
·

DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the ignition switch off and then to ON again.

·

Codes other than current DTCs B1622, B1623, B1632, B1633, B1642, B1692 and B1693 may be output at this time, but they are not related to this check.





A

2.CHECK CONNECTORS

B

18.CHECK HISTORY DTC

C

33.CHECK CONNECTORS

D

40.CHECK CURRENT DTC

E

2.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag ECU assembly, side airbag sensor assembly RH, side No. 2 airbag sensor assembly RH and rear airbag sensor RH. Also check that the connectors that link the No. 2 floor wire and front door wire RH are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag ECU assembly, side airbag sensor assembly RH, side No. 2 airbag sensor assembly RH and rear airbag sensor RH. Also disconnect the connectors that link the No. 2 floor wire and front door wire RH.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.




OK

3.CHECK NO. 2 FLOOR WIRE (OPEN)

NG

REPLACE WIRE HARNESS

3.CHECK NO. 2 FLOOR WIRE (OPEN)
a.
U146991E02
1.74,3.76 2.125,4.198 true 1.635,3.771 1.26,4.208 true 1.604,2.469 1.604,1.979 1.604,1.979 1.448,1.979 false 1.865,0.844 1.5,1.115 true 2.063,0.635 2.448,1.115 true 1.99,1.094 1.99,1.271 false 1.01,2.448 1.135,2.604 0.125,0.156 10 false D 1.323,2.448 1.448,2.604 0.125,0.156 10 false C 1.781,2.448 1.906,2.604 0.125,0.156 10 false B 2.094,2.448 2.219,2.604 0.125,0.156 10 false A 0.708,2.448 0.865,2.625 0.156,0.177 10 false *1 2.573,2.125 2.729,2.281 0.156,0.156 10 false *2 0.802,0.188 0.979,0.344 0.177,0.156 10 false *a 0.385,3.198 0.583,3.375 0.198,0.177 10 false *b 1.281,1.125 1.635,1.281 0.354,0.156 10 false BBR- 2.25,1.125 2.646,1.281 0.396,0.156 10 false BBR+ 1.24,0.552 1.438,0.708 0.198,0.156 10 false G1 0.552,3.646 0.833,3.802 0.281,0.156 10 false G16 1.875,4.219 2.323,4.375 0.448,0.156 10 false BUSIN 0.969,4.219 1.417,4.375 0.448,0.156 10 false RTNIN 1.25,1.896 1.427,2.063 0.177,0.167 10 false *3 1.917,1.271 2.073,1.427 0.156,0.156 10 false *4

Using a service wire, connect terminals 8 (BBR+) and 11 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-4 (BUSIN) - G16-3 (RTNIN) Always Below 1 Ω



c.

Disconnect the service wire from connector B.

Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Airbag ECU Assembly
*3 No. 2 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH)



OK

4.CHECK NO. 2 FLOOR WIRE (SHORT)

NG

REPLACE NO. 2 FLOOR WIRE

4.CHECK NO. 2 FLOOR WIRE (SHORT)
a.
U146993E02
1.49,2.448 1.24,2.823 true 1.677,2.448 1.917,2.823 true 1.552,0.948 1.552,0.344 1.552,0.344 1.323,0.344 false 0.958,0.948 1.083,1.104 0.125,0.156 10 false D 1.271,0.948 1.396,1.104 0.125,0.156 10 false C 1.719,0.948 1.844,1.104 0.125,0.156 10 false B 2.042,0.948 2.167,1.104 0.125,0.156 10 false A 0.646,0.927 0.792,1.104 0.146,0.177 10 false *1 2.448,0.656 2.656,0.813 0.208,0.156 10 false *2 1.135,0.26 1.313,0.417 0.177,0.156 10 false *3 0.333,1.75 0.563,1.927 0.229,0.177 10 false *a 0.479,2.323 0.76,2.479 0.281,0.156 10 false G16 0.896,2.854 1.344,3.01 0.448,0.156 10 false RTNIN 1.75,2.865 2.198,3.021 0.448,0.156 10 false BUSIN

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-4 (BUSIN) - G16-3 (RTNIN) Always 1 MΩ or higher


Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Airbag ECU Assembly
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH)



OK

5.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)

NG

REPLACE NO. 2 FLOOR WIRE

5.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)
a.
U146993E02
1.49,2.448 1.24,2.823 true 1.677,2.448 1.917,2.823 true 1.552,0.948 1.552,0.344 1.552,0.344 1.323,0.344 false 0.958,0.948 1.083,1.104 0.125,0.156 10 false D 1.271,0.948 1.396,1.104 0.125,0.156 10 false C 1.719,0.948 1.844,1.104 0.125,0.156 10 false B 2.042,0.948 2.167,1.104 0.125,0.156 10 false A 0.646,0.927 0.792,1.104 0.146,0.177 10 false *1 2.448,0.656 2.656,0.813 0.208,0.156 10 false *2 1.135,0.26 1.313,0.417 0.177,0.156 10 false *3 0.333,1.75 0.563,1.927 0.229,0.177 10 false *a 0.479,2.323 0.76,2.479 0.281,0.156 10 false G16 0.896,2.854 1.344,3.01 0.448,0.156 10 false RTNIN 1.75,2.865 2.198,3.021 0.448,0.156 10 false BUSIN

Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G16-4 (BUSIN) - Body ground Ignition switch ON Below 1 V
G16-3 (RTNIN) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Airbag ECU Assembly
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH)



OK

6.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE NO. 2 FLOOR WIRE

6.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)
a.
U146993E02
1.49,2.448 1.24,2.823 true 1.677,2.448 1.917,2.823 true 1.552,0.948 1.552,0.344 1.552,0.344 1.323,0.344 false 0.958,0.948 1.083,1.104 0.125,0.156 10 false D 1.271,0.948 1.396,1.104 0.125,0.156 10 false C 1.719,0.948 1.844,1.104 0.125,0.156 10 false B 2.042,0.948 2.167,1.104 0.125,0.156 10 false A 0.646,0.927 0.792,1.104 0.146,0.177 10 false *1 2.448,0.656 2.656,0.813 0.208,0.156 10 false *2 1.135,0.26 1.313,0.417 0.177,0.156 10 false *3 0.333,1.75 0.563,1.927 0.229,0.177 10 false *a 0.479,2.323 0.76,2.479 0.281,0.156 10 false G16 0.896,2.854 1.344,3.01 0.448,0.156 10 false RTNIN 1.75,2.865 2.198,3.021 0.448,0.156 10 false BUSIN

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-4 (BUSIN) - Body ground Always 1 MΩ or higher
G16-3 (RTNIN) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Airbag ECU Assembly
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH)



OK

7.CHECK NO. 2 FLOOR WIRE (OPEN)

NG

REPLACE NO. 2 FLOOR WIRE

7.CHECK NO. 2 FLOOR WIRE (OPEN)
a.
U147003E02
1.802,0.708 1.458,1.052 true 1.958,0.719 2.292,1.063 true 1.708,2.333 1.708,1.854 1.708,1.854 1.531,1.854 false 1.531,3.656 1.208,4.031 true 1.677,3.656 2,4.031 true 1.594,4.021 1.594,4.302 false 1.177,2.323 1.302,2.479 0.125,0.156 10 false D 1.479,2.323 1.604,2.479 0.125,0.156 10 false C 1.833,2.323 1.958,2.479 0.125,0.156 10 false B 2.146,2.323 2.271,2.479 0.125,0.156 10 false A 0.781,2.323 0.948,2.469 0.167,0.146 10 false *1 0.667,0.177 0.865,0.354 0.198,0.177 10 false *a 0.375,3.219 0.552,3.375 0.177,0.156 10 false *b 0.906,4.063 1.344,4.219 0.438,0.156 10 false RTNIN 1.802,4.083 2.24,4.24 0.438,0.156 10 false BUSIN 0.552,3.573 0.833,3.729 0.281,0.156 10 false G14 1.052,0.594 1.333,0.75 0.281,0.156 10 false G16 2.083,1.104 2.677,1.26 0.594,0.156 10 false RTNOUT 1.052,1.083 1.656,1.24 0.604,0.156 10 false BUSOUT 1.333,1.771 1.49,1.927 0.156,0.156 10 false *3 2.448,2.323 2.625,2.49 0.177,0.167 10 false *2 1.51,4.323 1.667,4.479 0.156,0.156 10 false *4

Using a service wire, connect terminals 3 (RTNIN) and 4 (BUSIN) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-1 (BUSOUT) - G16-2 (RTNOUT) Always Below 1 Ω



c.

Disconnect the service wire from connector C.

Text in Illustration
*1 Rear Airbag Sensor RH
*2 Side No. 2 Airbag Sensor Assembly RH
*3 No. 2 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH)
*b Front view of wire harness connector
(to Rear Airbag Sensor RH)



OK

8.CHECK NO. 2 FLOOR WIRE (SHORT)

NG

REPLACE NO. 2 FLOOR WIRE

8.CHECK NO. 2 FLOOR WIRE (SHORT)
U146996E02
2.073,2.448 1.677,2.833 true 2.24,2.458 2.635,2.844 true 1.74,0.74 1.74,0.208 1.74,0.208 1.573,0.208 false 1.146,0.74 1.271,0.896 0.125,0.156 10 false D 1.458,0.74 1.583,0.896 0.125,0.156 10 false C 1.906,0.74 2.031,0.896 0.125,0.156 10 false B 2.219,0.74 2.344,0.896 0.125,0.156 10 false A 0.833,0.719 1.021,0.875 0.188,0.156 10 false *1 2.458,0.729 2.635,0.885 0.177,0.156 10 false *2 1.375,0.125 1.552,0.281 0.177,0.156 10 false *3 0.99,1.875 1.177,2.021 0.188,0.146 10 false *a 1.271,2.333 1.552,2.49 0.281,0.156 10 false G16 2.354,2.865 2.958,3.021 0.604,0.156 10 false RTNOUT 1.333,2.865 1.938,3.021 0.604,0.156 10 false BUSOUT

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-1 (BUSOUT) - G16-2 (RTNOUT) Always 1 MΩ or higher


Text in Illustration
*1 Rear Airbag Sensor RH
*2 Side No. 2 Airbag Sensor Assembly RH
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH)



OK

9.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)

NG

REPLACE NO. 2 FLOOR WIRE

9.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)
a.
U146996E02
2.073,2.448 1.677,2.833 true 2.24,2.458 2.635,2.844 true 1.74,0.74 1.74,0.208 1.74,0.208 1.573,0.208 false 1.146,0.74 1.271,0.896 0.125,0.156 10 false D 1.458,0.74 1.583,0.896 0.125,0.156 10 false C 1.906,0.74 2.031,0.896 0.125,0.156 10 false B 2.219,0.74 2.344,0.896 0.125,0.156 10 false A 0.833,0.719 1.021,0.875 0.188,0.156 10 false *1 2.458,0.729 2.635,0.885 0.177,0.156 10 false *2 1.375,0.125 1.552,0.281 0.177,0.156 10 false *3 0.99,1.875 1.177,2.021 0.188,0.146 10 false *a 1.271,2.333 1.552,2.49 0.281,0.156 10 false G16 2.354,2.865 2.958,3.021 0.604,0.156 10 false RTNOUT 1.333,2.865 1.938,3.021 0.604,0.156 10 false BUSOUT

Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G16-1 (BUSOUT) - Body ground Ignition switch ON Below 1 V
G16-2 (RTNOUT) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Text in Illustration
*1 Rear Airbag Sensor RH
*2 Side No. 2 Airbag Sensor Assembly RH
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH)



OK

10.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE NO. 2 FLOOR WIRE

10.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)
a.
U146996E02
2.073,2.448 1.677,2.833 true 2.24,2.458 2.635,2.844 true 1.74,0.74 1.74,0.208 1.74,0.208 1.573,0.208 false 1.146,0.74 1.271,0.896 0.125,0.156 10 false D 1.458,0.74 1.583,0.896 0.125,0.156 10 false C 1.906,0.74 2.031,0.896 0.125,0.156 10 false B 2.219,0.74 2.344,0.896 0.125,0.156 10 false A 0.833,0.719 1.021,0.875 0.188,0.156 10 false *1 2.458,0.729 2.635,0.885 0.177,0.156 10 false *2 1.375,0.125 1.552,0.281 0.177,0.156 10 false *3 0.99,1.875 1.177,2.021 0.188,0.146 10 false *a 1.271,2.333 1.552,2.49 0.281,0.156 10 false G16 2.354,2.865 2.958,3.021 0.604,0.156 10 false RTNOUT 1.333,2.865 1.938,3.021 0.604,0.156 10 false BUSOUT

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-1 (BUSOUT) - Body ground Always 1 MΩ or higher
G16-2 (RTNOUT) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Rear Airbag Sensor RH
*2 Side No. 2 Airbag Sensor Assembly RH
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH)



OK

11.CHECK SIDE AIRBAG SENSOR RH CIRCUIT (OPEN)

NG

REPLACE NO. 2 FLOOR WIRE

11.CHECK SIDE AIRBAG SENSOR RH CIRCUIT (OPEN)
a.
U147006E02
1.344,3.646 0.906,4.01 true 1.594,3.656 2.031,4.021 true 1.802,0.74 1.469,1.073 true 1.969,0.75 2.302,1.083 true 1.458,4.063 1.458,4.281 false 1.573,2.323 1.698,2.479 0.125,0.156 10 false D 1.729,2.323 1.854,2.479 0.125,0.156 10 false C 2.083,2.323 2.208,2.479 0.125,0.156 10 false B 2.385,2.323 2.51,2.479 0.125,0.156 10 false A 2.698,2.292 2.885,2.469 0.188,0.177 10 false *2 0.5,2.292 0.719,2.479 0.219,0.188 10 false *1 0.354,3.167 0.521,3.333 0.167,0.167 10 false *b 0.698,0.198 0.885,0.427 0.188,0.229 10 false *a 0.635,4.031 1.073,4.188 0.438,0.156 10 false RTNIN 1.854,4.031 2.302,4.188 0.448,0.156 10 false BUSIN 0.698,3.531 0.875,3.688 0.177,0.156 10 false F2 1.052,0.677 1.333,0.833 0.281,0.156 10 false G14 2.135,1.125 2.729,1.281 0.594,0.156 10 false RTNOUT 1.063,1.115 1.667,1.271 0.604,0.156 10 false BUSOUT 0.917,2.333 1.042,2.49 0.125,0.156 10 false F 1.229,2.323 1.354,2.479 0.125,0.156 10 false E 1.375,4.281 1.531,4.458 0.156,0.177 10 false *3

Connect the connectors that link the No. 2 floor wire and front door wire RH.


b.

Using a service wire, connect terminals 2 (BUSIN) and 1 (RTNIN) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G14-1 (BUSOUT) - G14-2 (RTNOUT) Always Below 1 Ω


Text in Illustration
*1 Side Airbag Sensor Assembly RH
*2 Rear Airbag Sensor RH
*3 Service Wire
*a Front view of wire harness connector
(to Rear Airbag Sensor RH)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)



OK

12.CHECK SIDE AIRBAG SENSOR RH CIRCUIT (SHORT)

NG

43.CHECK FRONT DOOR WIRE RH (OPEN)
12.CHECK SIDE AIRBAG SENSOR RH CIRCUIT (SHORT)
a.
U147008E02
1.49,2.365 1.104,2.74 true 1.667,2.365 2.063,2.74 true 1.573,0.688 1.698,0.844 0.125,0.156 10 false D 1.74,0.688 1.865,0.844 0.125,0.156 10 false C 2.083,0.688 2.208,0.844 0.125,0.156 10 false B 2.385,0.688 2.51,0.844 0.125,0.156 10 false A 2.688,0.677 2.875,0.844 0.188,0.167 10 false *2 0.521,0.677 0.708,0.844 0.188,0.167 10 false *1 0.5,1.74 0.656,1.896 0.156,0.156 10 false *a 0.708,2.25 0.99,2.406 0.281,0.156 10 false G14 1.844,2.781 2.438,2.938 0.594,0.156 10 false RTNOUT 0.688,2.781 1.281,2.938 0.594,0.156 10 false BUSOUT 0.938,0.688 1.063,0.844 0.125,0.156 10 false F 1.229,0.688 1.354,0.844 0.125,0.156 10 false E

Disconnect the service wire from connector E.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G14-1 (BUSOUT) - G14-2 (RTNOUT) Always 1 MΩ or higher


Text in Illustration
*1 Side Airbag Sensor Assembly RH
*2 Rear Airbag Sensor RH
*a Front view of wire harness connector
(to Rear Airbag Sensor RH)



OK

13.CHECK SIDE AIRBAG SENSOR RH CIRCUIT (SHORT TO B+)

NG

44.CHECK FRONT DOOR WIRE RH (SHORT)
13.CHECK SIDE AIRBAG SENSOR RH CIRCUIT (SHORT TO B+)
a.
U147008E02
1.49,2.365 1.104,2.74 true 1.667,2.365 2.063,2.74 true 1.573,0.688 1.698,0.844 0.125,0.156 10 false D 1.74,0.688 1.865,0.844 0.125,0.156 10 false C 2.083,0.688 2.208,0.844 0.125,0.156 10 false B 2.385,0.688 2.51,0.844 0.125,0.156 10 false A 2.688,0.677 2.875,0.844 0.188,0.167 10 false *2 0.521,0.677 0.708,0.844 0.188,0.167 10 false *1 0.5,1.74 0.656,1.896 0.156,0.156 10 false *a 0.708,2.25 0.99,2.406 0.281,0.156 10 false G14 1.844,2.781 2.438,2.938 0.594,0.156 10 false RTNOUT 0.688,2.781 1.281,2.938 0.594,0.156 10 false BUSOUT 0.938,0.688 1.063,0.844 0.125,0.156 10 false F 1.229,0.688 1.354,0.844 0.125,0.156 10 false E

Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G14-1 (BUSOUT) - Body ground Ignition switch ON Below 1 V
G14-2 (RTNOUT) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Text in Illustration
*1 Side Airbag Sensor Assembly RH
*2 Rear Airbag Sensor RH
*a Front view of wire harness connector
(to Rear Airbag Sensor RH)



OK

14.CHECK SIDE AIRBAG SENSOR RH CIRCUIT (SHORT TO GROUND)

NG

45.CHECK FRONT DOOR WIRE RH (SHORT TO B+)
14.CHECK SIDE AIRBAG SENSOR RH CIRCUIT (SHORT TO GROUND)
a.
U147008E02
1.49,2.365 1.104,2.74 true 1.667,2.365 2.063,2.74 true 1.573,0.688 1.698,0.844 0.125,0.156 10 false D 1.74,0.688 1.865,0.844 0.125,0.156 10 false C 2.083,0.688 2.208,0.844 0.125,0.156 10 false B 2.385,0.688 2.51,0.844 0.125,0.156 10 false A 2.688,0.677 2.875,0.844 0.188,0.167 10 false *2 0.521,0.677 0.708,0.844 0.188,0.167 10 false *1 0.5,1.74 0.656,1.896 0.156,0.156 10 false *a 0.708,2.25 0.99,2.406 0.281,0.156 10 false G14 1.844,2.781 2.438,2.938 0.594,0.156 10 false RTNOUT 0.688,2.781 1.281,2.938 0.594,0.156 10 false BUSOUT 0.938,0.688 1.063,0.844 0.125,0.156 10 false F 1.229,0.688 1.354,0.844 0.125,0.156 10 false E

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G14-1 (BUSOUT) - Body ground Always 1 MΩ or higher
G14-2 (RTNOUT) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Side Airbag Sensor Assembly RH
*2 Rear Airbag Sensor RH
*a Front view of wire harness connector
(to Rear Airbag Sensor RH)



OK

15.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH

NG

46.CHECK FRONT DOOR WIRE RH (SHORT TO GROUND)
15.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH
a.
C238218E01
0.793,1.142 0.979,1.302 0.186,0.159 10 *1 2.307,0.855 2.493,1.014 0.186,0.159 10 *2 1.718,1.142 1.861,1.293 0.143,0.151 10 B 1.873,1.142 2.016,1.293 0.143,0.151 10 A 1.257,1.142 1.400,1.293 0.143,0.151 10 C 1.1,1.142 1.243,1.293 0.143,0.151 10 D

Connect the connectors to the rear airbag sensor RH, side airbag sensor assembly RH and airbag ECU assembly.


b.

Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) battery terminal.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1642 is output. A
DTC B1647 is output. B
DTCs B1642 and B1647 are not output. C


HINT:

Codes other than DTCs B1642 and B1647 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.

Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Airbag ECU Assembly



A

16.CHECK REAR AIRBAG SENSOR RH

B

C

16.CHECK REAR AIRBAG SENSOR RH
a.
C238223E01
0.969,0.972 1.119,1.124 0.150,0.152 10 *1 2.271,0.972 2.420,1.124 0.150,0.152 10 *2 2.036,0.972 2.163,1.137 0.128,0.166 10 A 1.883,0.972 2.011,1.137 0.128,0.166 10 B 1.425,0.972 1.552,1.137 0.128,0.166 10 C 1.268,0.972 1.396,1.137 0.128,0.166 10 D

Interchange the rear airbag sensor RH with LH and connect the connectors to them.


b.

Connect the cable to the negative (-) battery terminal.



d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1642 is output. A
DTC B1647 is output. B
DTCs B1642 and B1647 are not output. C


HINT:

Codes other than DTCs B1642 and B1647 may be output at this time, but they are not related to this check.



g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



i.

Return the rear airbag sensor RH and LH to their original positions and connect the connectors.

Text in Illustration
*1 Rear Airbag Sensor LH
*2 Side No. 2 Airbag Sensor Assembly RH



A

17.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

B

C

17.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C238395E02
0.698,0.99 0.875,1.167 0.177,0.177 10 false *1 2.552,1 2.729,1.177 0.177,0.177 10 false *2 2.25,1 2.375,1.198 0.125,0.198 10 false A 2.104,1 2.229,1.198 0.125,0.198 10 false B 1.75,1 1.875,1.198 0.125,0.198 10 false C 1.583,1 1.708,1.198 0.125,0.198 10 false D 1.25,1 1.375,1.198 0.125,0.198 10 false E 1.094,1 1.219,1.198 0.125,0.198 10 false F

Interchange the side airbag sensor assembly RH with LH and connect the connectors.


b.

Connect the cable to the negative (-) battery terminal.



d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1642 is output. A
DTC B1647 is output. B
DTCs B1642 and B1647 are not output. C


HINT:

Codes other than DTCs B1642 and B1647 may be output at this time, but they are not related to this check.



g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



i.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.

Text in Illustration
*1 Side Airbag Sensor Assembly LH
*2 Rear Airbag Sensor RH



A

B

C

18.CHECK HISTORY DTC
a.

Check for history DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
History DTCs B1622 and B1632 are not output. A
History DTC B1622 is output. B
History DTC B1632 is output. C


HINT:

Codes other than history DTCs B1622 and B1632 may be output at this time, but they are not related to this check.




A

19.CHECK CURRENT DTC

B

41.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH

C

42.CHECK REAR AIRBAG SENSOR RH
19.CHECK CURRENT DTC
a.

Check for current DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
Current DTC B1623 is output. A
Current DTC B1633 is output. B


HINT:

Codes other than current DTCs B1623 and B1633 may be output at this time, but they are not related to this check.




A

20.CHECK CONNECTORS

B

26.CHECK CONNECTORS
20.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag ECU assembly and side No. 2 airbag sensor assembly RH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag ECU assembly and side No. 2 airbag sensor assembly RH.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.




OK

21.CHECK NO. 2 FLOOR WIRE (OPEN)

NG

REPLACE NO. 2 FLOOR WIRE

21.CHECK NO. 2 FLOOR WIRE (OPEN)
a.
U146992E03
1.76,3.771 2.135,4.208 true 1.656,3.771 1.281,4.208 true 1.604,2.469 1.604,1.979 1.604,1.979 1.448,1.979 false 1.865,0.844 1.5,1.115 true 2.094,0.625 2.448,1.115 true 2,1.052 2,1.229 false 1.01,2.469 1.135,2.625 0.125,0.156 10 false D 1.323,2.469 1.448,2.625 0.125,0.156 10 false C 1.781,2.469 1.906,2.625 0.125,0.156 10 false B 2.094,2.469 2.219,2.625 0.125,0.156 10 false A 0.708,2.448 0.865,2.625 0.156,0.177 10 false *1 2.573,2.125 2.729,2.281 0.156,0.156 10 false *2 0.802,0.188 0.979,0.344 0.177,0.156 10 false *a 0.385,3.198 0.583,3.375 0.198,0.177 10 false *b 1.281,1.125 1.635,1.281 0.354,0.156 10 false BBR- 2.25,1.125 2.646,1.281 0.396,0.156 10 false BBR+ 1.198,0.552 1.573,0.823 0.375,0.271 10 false G20 0.625,3.656 0.958,3.875 0.333,0.219 10 false G16 1.875,4.219 2.323,4.375 0.448,0.156 10 false BUSIN 0.958,4.219 1.406,4.375 0.448,0.156 10 false RTNIN 1.25,1.896 1.427,2.063 0.177,0.167 10 false *3 1.906,1.24 2.063,1.396 0.156,0.156 10 false *4

Using a service wire, connect terminals 8 (BBR+) and 11 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-4 (BUSIN) - G16-3 (RTNIN) Always Below 1 Ω



c.

Disconnect the service wire from connector B.

Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Airbag ECU Assembly
*3 No. 2 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH)



OK

22.CHECK NO. 2 FLOOR WIRE (SHORT)

NG

REPLACE NO. 2 FLOOR WIRE

22.CHECK NO. 2 FLOOR WIRE (SHORT)
a.
U146994E01
0.955,0.93 1.076,1.083 0.121,0.153 10 D 1.271,0.93 1.392,1.083 0.121,0.153 10 C 1.72,0.93 1.841,1.083 0.121,0.153 10 B 2.041,0.93 2.162,1.083 0.121,0.153 10 A 0.641,0.93 0.793,1.111 0.151,0.181 10 *1 2.437,0.64 2.641,0.792 0.204,0.152 10 *2 1.131,0.259 1.310,0.412 0.179,0.152 10 *3 0.334,1.749 0.568,1.925 0.234,0.175 10 *a 0.464,2.306 0.744,2.464 0.280,0.158 10 G16 0.941,2.844 1.394,3.002 0.453,0.158 10 RTNIN 1.716,2.844 2.159,3.002 0.443,0.158 10 BUSIN 1.507,2.453 1.263,2.825 false 1.685,2.453 1.929,2.825 false 1.555,0.943 1.555,0.346 1.555,0.346 1.327,0.346 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-4 (BUSIN) - G16-3 (RTNIN) Always 1 MΩ or higher


Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Airbag ECU Assembly
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH)



OK

23.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)

NG

REPLACE NO. 2 FLOOR WIRE

23.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)
a.
U146994E02
1.5,2.448 1.25,2.823 true 1.667,2.458 1.906,2.833 true 1.552,0.969 1.552,0.365 1.552,0.365 1.323,0.365 false 0.958,0.948 1.083,1.104 0.125,0.156 10 false D 1.271,0.948 1.396,1.104 0.125,0.156 10 false C 1.719,0.948 1.844,1.104 0.125,0.156 10 false B 2.031,0.948 2.156,1.104 0.125,0.156 10 false A 0.646,0.927 0.792,1.104 0.146,0.177 10 false *1 2.438,0.635 2.646,0.792 0.208,0.156 10 false *2 1.135,0.26 1.313,0.417 0.177,0.156 10 false *3 0.333,1.75 0.563,1.927 0.229,0.177 10 false *a 0.469,2.313 0.75,2.469 0.281,0.156 10 false G16 0.917,2.854 1.365,3.01 0.448,0.156 10 false RTNIN 1.792,2.844 2.24,3 0.448,0.156 10 false BUSIN

Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G16-4 (BUSIN) - Body ground Ignition switch ON Below 1 V
G16-3 (RTNIN) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Airbag ECU Assembly
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH)



OK

24.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE NO. 2 FLOOR WIRE

24.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)
a.
U146994E02
1.5,2.448 1.25,2.823 true 1.667,2.458 1.906,2.833 true 1.552,0.969 1.552,0.365 1.552,0.365 1.323,0.365 false 0.958,0.948 1.083,1.104 0.125,0.156 10 false D 1.271,0.948 1.396,1.104 0.125,0.156 10 false C 1.719,0.948 1.844,1.104 0.125,0.156 10 false B 2.031,0.948 2.156,1.104 0.125,0.156 10 false A 0.646,0.927 0.792,1.104 0.146,0.177 10 false *1 2.438,0.635 2.646,0.792 0.208,0.156 10 false *2 1.135,0.26 1.313,0.417 0.177,0.156 10 false *3 0.333,1.75 0.563,1.927 0.229,0.177 10 false *a 0.469,2.313 0.75,2.469 0.281,0.156 10 false G16 0.917,2.854 1.365,3.01 0.448,0.156 10 false RTNIN 1.792,2.844 2.24,3 0.448,0.156 10 false BUSIN

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-4 (BUSIN) - Body ground Always 1 MΩ or higher
G16-3 (RTNIN) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Airbag ECU Assembly
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH)



OK

25.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH

NG

REPLACE NO. 2 FLOOR WIRE

25.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH
a.
C238218E02
0.792,1.167 0.979,1.323 0.188,0.156 10 false *1 2.302,0.885 2.49,1.042 0.188,0.156 10 false *2 1.719,1.167 1.865,1.313 0.146,0.146 10 false B 1.875,1.167 2.021,1.313 0.146,0.146 10 false A 1.271,1.167 1.417,1.313 0.146,0.146 10 false C 1.115,1.167 1.26,1.313 0.146,0.146 10 false D

Connect the connector to the airbag ECU assembly.


b.

Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) battery terminal.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1623 is output. A
DTC B1628 is output. B
DTCs B1623 and B1628 are not output. C


HINT:

Codes other than DTCs B1623 and B1628 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.

Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Airbag ECU Assembly



A

B

C

26.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the side No. 2 airbag sensor assembly RH and rear airbag sensor RH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the side No. 2 airbag sensor assembly RH and rear airbag sensor RH.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.




OK

27.CHECK NO. 2 FLOOR WIRE (OPEN)

NG

REPLACE WIRE HARNESS

27.CHECK NO. 2 FLOOR WIRE (OPEN)
a.
U147004E02
1.823,0.698 1.479,1.042 false 1.979,0.698 2.313,1.042 false 1.698,2.333 1.698,1.854 1.698,1.854 1.521,1.854 false 1.531,3.656 1.208,4.031 true 1.677,3.656 2,4.031 true 1.594,4.031 1.594,4.313 false 1.177,2.333 1.302,2.49 0.125,0.156 10 false D 1.479,2.333 1.604,2.49 0.125,0.156 10 false C 1.833,2.333 1.958,2.49 0.125,0.156 10 false B 2.146,2.333 2.271,2.49 0.125,0.156 10 false A 0.771,2.323 0.938,2.469 0.167,0.146 10 false *1 0.667,0.177 0.865,0.354 0.198,0.177 10 false *a 0.354,3.208 0.531,3.365 0.177,0.156 10 false *b 0.875,4.073 1.323,4.229 0.448,0.156 10 false RTNIN 1.823,4.073 2.271,4.229 0.448,0.156 10 false BUSIN 0.552,3.594 0.833,3.75 0.281,0.156 10 false G14 1.042,0.604 1.323,0.76 0.281,0.156 10 false G16 1.969,1.073 2.563,1.229 0.594,0.156 10 false RTNOUT 1.104,1.073 1.698,1.229 0.594,0.156 10 false BUSOUT 1.333,1.771 1.49,1.927 0.156,0.156 10 false *3 2.448,2.323 2.625,2.49 0.177,0.167 10 false *2 1.51,4.323 1.667,4.479 0.156,0.156 10 false *4

Using a service wire, connect terminals 4 (BUSIN) and 3 (RTNIN) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-1 (BUSOUT) - G16-2 (RTNOUT) Always Below 1 Ω



c.

Disconnect the service wire from connector C.

Text in Illustration
*1 Rear Airbag Sensor RH
*2 Side No. 2 Airbag Sensor Assembly RH
*3 No. 2 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH)
*b Front view of wire harness connector
(to Rear Airbag Sensor RH)



OK

28.CHECK NO. 2 FLOOR WIRE (SHORT)

NG

REPLACE NO. 2 FLOOR WIRE

28.CHECK NO. 2 FLOOR WIRE (SHORT)
U146995E02
2.073,2.458 1.719,2.844 true 2.24,2.458 2.656,2.844 true 1.729,0.74 1.729,0.208 1.729,0.208 1.563,0.208 false 1.146,0.74 1.271,0.896 0.125,0.156 10 false D 1.458,0.74 1.583,0.896 0.125,0.156 10 false C 1.906,0.74 2.031,0.896 0.125,0.156 10 false B 2.219,0.74 2.344,0.896 0.125,0.156 10 false A 0.813,0.729 1,0.885 0.188,0.156 10 false *1 2.458,0.74 2.635,0.896 0.177,0.156 10 false *2 1.375,0.125 1.552,0.281 0.177,0.156 10 false *3 1.01,1.896 1.198,2.042 0.188,0.146 10 false *a 1.271,2.323 1.552,2.479 0.281,0.156 10 false G16 2.396,2.865 3,3.021 0.604,0.156 10 false RTNOUT 1.438,2.865 2.031,3.021 0.594,0.156 10 false BUSOUT

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-1 (BUSOUT) - G16-2 (RTNOUT) Always 1 MΩ or higher


Text in Illustration
*1 Rear Airbag Sensor RH
*2 Side No. 2 Airbag Sensor Assembly RH
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH)



OK

29.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)

NG

REPLACE NO. 2 FLOOR WIRE

29.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)
a.
U146995E02
2.073,2.458 1.719,2.844 true 2.24,2.458 2.656,2.844 true 1.729,0.74 1.729,0.208 1.729,0.208 1.563,0.208 false 1.146,0.74 1.271,0.896 0.125,0.156 10 false D 1.458,0.74 1.583,0.896 0.125,0.156 10 false C 1.906,0.74 2.031,0.896 0.125,0.156 10 false B 2.219,0.74 2.344,0.896 0.125,0.156 10 false A 0.813,0.729 1,0.885 0.188,0.156 10 false *1 2.458,0.74 2.635,0.896 0.177,0.156 10 false *2 1.375,0.125 1.552,0.281 0.177,0.156 10 false *3 1.01,1.896 1.198,2.042 0.188,0.146 10 false *a 1.271,2.323 1.552,2.479 0.281,0.156 10 false G16 2.396,2.865 3,3.021 0.604,0.156 10 false RTNOUT 1.438,2.865 2.031,3.021 0.594,0.156 10 false BUSOUT

Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G16-1 (BUSOUT) - Body ground Ignition switch ON Below 1 V
G16-2 (RTNOUT) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Text in Illustration
*1 Rear Airbag Sensor RH
*2 Side No. 2 Airbag Sensor Assembly RH
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH)



OK

30.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE NO. 2 FLOOR WIRE

30.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)
a.
U146995E02
2.073,2.458 1.719,2.844 true 2.24,2.458 2.656,2.844 true 1.729,0.74 1.729,0.208 1.729,0.208 1.563,0.208 false 1.146,0.74 1.271,0.896 0.125,0.156 10 false D 1.458,0.74 1.583,0.896 0.125,0.156 10 false C 1.906,0.74 2.031,0.896 0.125,0.156 10 false B 2.219,0.74 2.344,0.896 0.125,0.156 10 false A 0.813,0.729 1,0.885 0.188,0.156 10 false *1 2.458,0.74 2.635,0.896 0.177,0.156 10 false *2 1.375,0.125 1.552,0.281 0.177,0.156 10 false *3 1.01,1.896 1.198,2.042 0.188,0.146 10 false *a 1.271,2.323 1.552,2.479 0.281,0.156 10 false G16 2.396,2.865 3,3.021 0.604,0.156 10 false RTNOUT 1.438,2.865 2.031,3.021 0.594,0.156 10 false BUSOUT

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-1 (BUSOUT) - Body ground Always 1 MΩ or higher
G16-2 (RTNOUT) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Rear Airbag Sensor RH
*2 Side No. 2 Airbag Sensor Assembly RH
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH)



OK

31.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH

NG

REPLACE NO. 2 FLOOR WIRE

31.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH
a.
C238218E02
0.792,1.167 0.979,1.323 0.188,0.156 10 false *1 2.302,0.885 2.49,1.042 0.188,0.156 10 false *2 1.719,1.167 1.865,1.313 0.146,0.146 10 false B 1.875,1.167 2.021,1.313 0.146,0.146 10 false A 1.271,1.167 1.417,1.313 0.146,0.146 10 false C 1.115,1.167 1.26,1.313 0.146,0.146 10 false D

Connect the connector to the rear airbag sensor RH.


b.

Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) battery terminal.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1633 is output. A
DTC B1638 is output. B
DTCs B1633 and B1638 are not output. C


HINT:

Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.

Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Airbag ECU Assembly



A

32.CHECK REAR AIRBAG SENSOR RH

B

C

32.CHECK REAR AIRBAG SENSOR RH
a.
C238223E03
0.969,1 1.115,1.156 0.146,0.156 10 false *1 2.271,1 2.417,1.156 0.146,0.156 10 false *2 2.031,1 2.156,1.167 0.125,0.167 10 false A 1.885,1 2.01,1.167 0.125,0.167 10 false B 1.427,1 1.552,1.167 0.125,0.167 10 false C 1.271,1 1.396,1.167 0.125,0.167 10 false D

Interchange the rear airbag sensor RH with LH and connect the connectors.


b.

Connect the cable to the negative (-) battery terminal.



d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1633 is output. A
DTC B1638 is output. B
DTCs B1633 and B1638 are not output. C


HINT:

Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.



g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



i.

Return the rear airbag sensor RH and LH to their original positions and connect the connectors.

Text in Illustration
*1 Rear Airbag Sensor LH
*2 Side No. 2 Airbag Sensor Assembly RH



A

B

C

33.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the rear airbag sensor RH and side airbag sensor assembly RH. Also check that the connectors that link the No. 2 floor wire and front door wire RH are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the rear airbag sensor RH and side airbag sensor assembly RH. Also disconnect the connectors that link the No. 2 floor wire and front door wire RH.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.




OK

34.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH CIRCUIT (OPEN)

NG

REPLACE WIRE HARNESS

34.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH CIRCUIT (OPEN)
a.
U147006E02
1.344,3.646 0.906,4.01 true 1.594,3.656 2.031,4.021 true 1.802,0.74 1.469,1.073 true 1.969,0.75 2.302,1.083 true 1.458,4.063 1.458,4.281 false 1.573,2.323 1.698,2.479 0.125,0.156 10 false D 1.729,2.323 1.854,2.479 0.125,0.156 10 false C 2.083,2.323 2.208,2.479 0.125,0.156 10 false B 2.385,2.323 2.51,2.479 0.125,0.156 10 false A 2.698,2.292 2.885,2.469 0.188,0.177 10 false *2 0.5,2.292 0.719,2.479 0.219,0.188 10 false *1 0.354,3.167 0.521,3.333 0.167,0.167 10 false *b 0.698,0.198 0.885,0.427 0.188,0.229 10 false *a 0.635,4.031 1.073,4.188 0.438,0.156 10 false RTNIN 1.854,4.031 2.302,4.188 0.448,0.156 10 false BUSIN 0.698,3.531 0.875,3.688 0.177,0.156 10 false F2 1.052,0.677 1.333,0.833 0.281,0.156 10 false G14 2.135,1.125 2.729,1.281 0.594,0.156 10 false RTNOUT 1.063,1.115 1.667,1.271 0.604,0.156 10 false BUSOUT 0.917,2.333 1.042,2.49 0.125,0.156 10 false F 1.229,2.323 1.354,2.479 0.125,0.156 10 false E 1.375,4.281 1.531,4.458 0.156,0.177 10 false *3

Connect the connectors that link the No. 2 floor wire and front door wire RH.


b.

Using a service wire, connect terminals 2 (BUSIN) and 1 (RTNIN) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G14-1 (BUSOUT) - G14-2 (RTNOUT) Always Below 1 Ω


Text in Illustration
*1 Side Airbag Sensor Assembly RH
*2 Rear Airbag Sensor RH
*3 Service Wire
*a Front view of wire harness connector
(to Rear Airbag Sensor RH)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)



OK

35.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH CIRCUIT (SHORT)

NG

43.CHECK FRONT DOOR WIRE RH (OPEN)
35.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH CIRCUIT (SHORT)
a.
U147008E02
1.49,2.365 1.104,2.74 true 1.667,2.365 2.063,2.74 true 1.573,0.688 1.698,0.844 0.125,0.156 10 false D 1.74,0.688 1.865,0.844 0.125,0.156 10 false C 2.083,0.688 2.208,0.844 0.125,0.156 10 false B 2.385,0.688 2.51,0.844 0.125,0.156 10 false A 2.688,0.677 2.875,0.844 0.188,0.167 10 false *2 0.521,0.677 0.708,0.844 0.188,0.167 10 false *1 0.5,1.74 0.656,1.896 0.156,0.156 10 false *a 0.708,2.25 0.99,2.406 0.281,0.156 10 false G14 1.844,2.781 2.438,2.938 0.594,0.156 10 false RTNOUT 0.688,2.781 1.281,2.938 0.594,0.156 10 false BUSOUT 0.938,0.688 1.063,0.844 0.125,0.156 10 false F 1.229,0.688 1.354,0.844 0.125,0.156 10 false E

Disconnect the service wire from connector E.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G14-1 (BUSOUT) - G14-2 (RTNOUT) Always 1 MΩ or higher


Text in Illustration
*1 Side Airbag Sensor Assembly RH
*2 Rear Airbag Sensor RH
*a Front view of wire harness connector
(to Rear Airbag Sensor RH)



OK

36.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH CIRCUIT (SHORT TO B+)

NG

44.CHECK FRONT DOOR WIRE RH (SHORT)
36.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH CIRCUIT (SHORT TO B+)
a.
U147008E02
1.49,2.365 1.104,2.74 true 1.667,2.365 2.063,2.74 true 1.573,0.688 1.698,0.844 0.125,0.156 10 false D 1.74,0.688 1.865,0.844 0.125,0.156 10 false C 2.083,0.688 2.208,0.844 0.125,0.156 10 false B 2.385,0.688 2.51,0.844 0.125,0.156 10 false A 2.688,0.677 2.875,0.844 0.188,0.167 10 false *2 0.521,0.677 0.708,0.844 0.188,0.167 10 false *1 0.5,1.74 0.656,1.896 0.156,0.156 10 false *a 0.708,2.25 0.99,2.406 0.281,0.156 10 false G14 1.844,2.781 2.438,2.938 0.594,0.156 10 false RTNOUT 0.688,2.781 1.281,2.938 0.594,0.156 10 false BUSOUT 0.938,0.688 1.063,0.844 0.125,0.156 10 false F 1.229,0.688 1.354,0.844 0.125,0.156 10 false E

Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G14-1 (BUSOUT) - Body ground Ignition switch ON Below 1 V
G14-2 (RTNOUT) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Text in Illustration
*1 Side Airbag Sensor Assembly RH
*2 Rear Airbag Sensor RH
*a Front view of wire harness connector
(to Rear Airbag Sensor RH)



OK

37.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH CIRCUIT (SHORT TO GROUND)

NG

45.CHECK FRONT DOOR WIRE RH (SHORT TO B+)
37.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH CIRCUIT (SHORT TO GROUND)
a.
U147008E02
1.49,2.365 1.104,2.74 true 1.667,2.365 2.063,2.74 true 1.573,0.688 1.698,0.844 0.125,0.156 10 false D 1.74,0.688 1.865,0.844 0.125,0.156 10 false C 2.083,0.688 2.208,0.844 0.125,0.156 10 false B 2.385,0.688 2.51,0.844 0.125,0.156 10 false A 2.688,0.677 2.875,0.844 0.188,0.167 10 false *2 0.521,0.677 0.708,0.844 0.188,0.167 10 false *1 0.5,1.74 0.656,1.896 0.156,0.156 10 false *a 0.708,2.25 0.99,2.406 0.281,0.156 10 false G14 1.844,2.781 2.438,2.938 0.594,0.156 10 false RTNOUT 0.688,2.781 1.281,2.938 0.594,0.156 10 false BUSOUT 0.938,0.688 1.063,0.844 0.125,0.156 10 false F 1.229,0.688 1.354,0.844 0.125,0.156 10 false E

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G14-1 (BUSOUT) - Body ground Always 1 MΩ or higher
G14-2 (RTNOUT) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Side Airbag Sensor Assembly RH
*2 Rear Airbag Sensor RH
*a Front view of wire harness connector
(to Rear Airbag Sensor RH)



OK

38.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

NG

46.CHECK FRONT DOOR WIRE RH (SHORT TO GROUND)
38.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C238395E02
0.698,0.99 0.875,1.167 0.177,0.177 10 false *1 2.552,1 2.729,1.177 0.177,0.177 10 false *2 2.25,1 2.375,1.198 0.125,0.198 10 false A 2.104,1 2.229,1.198 0.125,0.198 10 false B 1.75,1 1.875,1.198 0.125,0.198 10 false C 1.583,1 1.708,1.198 0.125,0.198 10 false D 1.25,1 1.375,1.198 0.125,0.198 10 false E 1.094,1 1.219,1.198 0.125,0.198 10 false F

Connect the connectors to the rear airbag sensor RH.


b.

Interchange the side airbag sensor assembly RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) battery terminal.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1692 or B1693 is output. A
DTC B1697 or B1698 is output. B
DTCs B1692, B1693, B1697 and B1698 are not output. C


HINT:

Codes other than DTCs B1692, B1693, B1697 and B1698 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.

Text in Illustration
*1 Side Airbag Sensor Assembly LH
*2 Rear Airbag Sensor RH



A

39.CHECK REAR AIRBAG SENSOR RH

B

C

39.CHECK REAR AIRBAG SENSOR RH
a.
C238223E03
0.969,1 1.115,1.156 0.146,0.156 10 false *1 2.271,1 2.417,1.156 0.146,0.156 10 false *2 2.031,1 2.156,1.167 0.125,0.167 10 false A 1.885,1 2.01,1.167 0.125,0.167 10 false B 1.427,1 1.552,1.167 0.125,0.167 10 false C 1.271,1 1.396,1.167 0.125,0.167 10 false D

Interchange the rear airbag sensor RH with LH and connect the connectors.


b.

Connect the cable to the negative (-) battery terminal.



d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1692 or B1693 is output. A
DTC B1697 or B1698 is output. B
DTCs B1692, B1693, B1697 and B1698 are not output. C


HINT:

Codes other than DTCs B1692, B1693, B1697 and B1698 may be output at this time, but they are not related to this check.



g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



i.

Return the rear airbag sensor RH and LH to their original positions and connect the connectors.

Text in Illustration
*1 Rear Airbag Sensor LH
*2 Side No. 2 Airbag Sensor Assembly RH



A

B

C

40.CHECK CURRENT DTC
a.

Check for current DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
Current DTC B1622 is output. A
Current DTC B1632 is output. B


HINT:

Codes other than current DTCs B1622 and B1632 may be output at this time, but they are not related to this check.



b.

Turn the ignition switch off.



A

41.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH

B

42.CHECK REAR AIRBAG SENSOR RH
41.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH
a.
C238218E02
0.792,1.167 0.979,1.323 0.188,0.156 10 false *1 2.302,0.885 2.49,1.042 0.188,0.156 10 false *2 1.719,1.167 1.865,1.313 0.146,0.146 10 false B 1.875,1.167 2.021,1.313 0.146,0.146 10 false A 1.271,1.167 1.417,1.313 0.146,0.146 10 false C 1.115,1.167 1.26,1.313 0.146,0.146 10 false D

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



b.

Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) battery terminal.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1622 is output. A
DTC B1627 is output. B
DTCs B1622 and B1627 are not output. C


HINT:

Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.

Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Airbag ECU Assembly



A

B

C

42.CHECK REAR AIRBAG SENSOR RH
a.
C238223E03
0.969,1 1.115,1.156 0.146,0.156 10 false *1 2.271,1 2.417,1.156 0.146,0.156 10 false *2 2.031,1 2.156,1.167 0.125,0.167 10 false A 1.885,1 2.01,1.167 0.125,0.167 10 false B 1.427,1 1.552,1.167 0.125,0.167 10 false C 1.271,1 1.396,1.167 0.125,0.167 10 false D

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



b.

Interchange the rear airbag sensor RH with LH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1632 is output. A
DTC B1637 is output. B
DTCs B1632 and B1637 are not output. C


HINT:

Codes other than DTCs B1632 and B1637 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the rear airbag sensor RH and LH to their original positions and connect the connectors.

Text in Illustration
*1 Rear Airbag Sensor LH
*2 Side No. 2 Airbag Sensor Assembly RH



A

B

C

43.CHECK FRONT DOOR WIRE RH (OPEN)
a.
U147010E02
1.583,3.677 1.948,4.188 true 1.323,3.667 0.958,4.156 true 1.438,2.469 1.438,2.844 1.438,2.844 1.635,2.844 false 2.042,2.333 2.042,1.854 2.042,1.854 2.198,1.854 false 1.448,4.073 1.448,4.292 false 1.563,2.333 1.688,2.49 0.125,0.156 10 false D 1.813,2.333 1.938,2.49 0.125,0.156 10 false C 2.167,2.323 2.292,2.479 0.125,0.156 10 false B 2.458,2.333 2.583,2.49 0.125,0.156 10 false A 2.771,2.333 2.938,2.5 0.167,0.167 10 false *2 0.531,2.313 0.74,2.479 0.208,0.167 10 false *1 0.375,3.188 0.594,3.417 0.219,0.229 10 false *b 0.698,0.219 0.906,0.365 0.208,0.146 10 false *a 1.719,4.208 2.323,4.365 0.604,0.156 10 false BUSOUT 0.646,4.198 1.083,4.354 0.438,0.156 10 false RTNIN 0.646,3.573 0.823,3.729 0.177,0.156 10 false F2 0.896,0.667 1.188,0.823 0.292,0.156 10 false FG1 2.25,1.771 2.427,1.917 0.177,0.146 10 false *4 0.948,2.333 1.073,2.49 0.125,0.156 10 false F 1.219,2.333 1.344,2.49 0.125,0.156 10 false E 1.677,2.75 1.854,2.948 0.177,0.198 10 false *3 1.375,4.323 1.531,4.469 0.156,0.146 10 false *5

Disconnect the front door wire RH connector from the No. 2 floor wire.

HINT:

The service wire has already been inserted into connector E.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FG1-1 - FG1-2 Always Below 1 Ω



c.

Disconnect the service wire from connector E.

Text in Illustration
*1 Side Airbag Sensor Assembly RH
*2 Rear Airbag Sensor RH
*3 Front Door Wire RH
*4 No. 2 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to No. 2 Floor Wire)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)



OK

REPLACE NO. 2 FLOOR WIRE

NG

REPLACE FRONT DOOR WIRE RH

44.CHECK FRONT DOOR WIRE RH (SHORT)
a.
U147012E02
1.406,0.76 1.406,0.354 1.406,0.354 1.563,0.354 false 2.01,0.896 2.01,1.24 2.01,1.24 2.094,1.24 false 1.521,0.75 1.646,0.906 0.125,0.156 10 false D 1.781,0.74 1.906,0.896 0.125,0.156 10 false C 2.146,0.74 2.271,0.896 0.125,0.156 10 false B 2.417,0.74 2.542,0.896 0.125,0.156 10 false A 2.719,0.729 2.885,0.896 0.167,0.167 10 false *2 0.479,0.656 0.688,0.802 0.208,0.146 10 false *1 0.375,1.604 0.573,1.771 0.198,0.167 10 false *a 0.708,2.177 1.042,2.333 0.333,0.156 10 false FG1 2.156,1.167 2.323,1.313 0.167,0.146 10 false *4 0.906,0.76 1.031,0.917 0.125,0.156 10 false F 1.177,0.75 1.302,0.906 0.125,0.156 10 false E 1.594,0.281 1.781,0.448 0.188,0.167 10 false *3

Disconnect the front door wire RH connector from the No. 2 floor wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FG1-1 - FG1-2 Always 1 MΩ or higher


Text in Illustration
*1 Side Airbag Sensor Assembly RH
*2 Rear Airbag Sensor RH
*3 Front Door Wire RH
*4 No. 2 Floor Wire
*a Front view of wire harness connector
(to No. 2 Floor Wire)



OK

REPLACE NO. 2 FLOOR WIRE

NG

REPLACE FRONT DOOR WIRE RH

45.CHECK FRONT DOOR WIRE RH (SHORT TO B+)
a.
U147012E02
1.406,0.76 1.406,0.354 1.406,0.354 1.563,0.354 false 2.01,0.896 2.01,1.24 2.01,1.24 2.094,1.24 false 1.521,0.75 1.646,0.906 0.125,0.156 10 false D 1.781,0.74 1.906,0.896 0.125,0.156 10 false C 2.146,0.74 2.271,0.896 0.125,0.156 10 false B 2.417,0.74 2.542,0.896 0.125,0.156 10 false A 2.719,0.729 2.885,0.896 0.167,0.167 10 false *2 0.479,0.656 0.688,0.802 0.208,0.146 10 false *1 0.375,1.604 0.573,1.771 0.198,0.167 10 false *a 0.708,2.177 1.042,2.333 0.333,0.156 10 false FG1 2.156,1.167 2.323,1.313 0.167,0.146 10 false *4 0.906,0.76 1.031,0.917 0.125,0.156 10 false F 1.177,0.75 1.302,0.906 0.125,0.156 10 false E 1.594,0.281 1.781,0.448 0.188,0.167 10 false *3

Disconnect the front door wire RH connector from the No. 2 floor wire.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
FG1-1 - Body ground Ignition switch ON Below 1 V
FG1-2 - Body ground Ignition switch ON Below 1 V


Text in Illustration
*1 Side Airbag Sensor Assembly RH
*2 Rear Airbag Sensor RH
*3 Front Door Wire RH
*4 No. 2 Floor Wire
*a Front view of wire harness connector
(to No. 2 Floor Wire)



OK

REPLACE NO. 2 FLOOR WIRE

NG

REPLACE FRONT DOOR WIRE RH

46.CHECK FRONT DOOR WIRE RH (SHORT TO GROUND)
a.
U147012E02
1.406,0.76 1.406,0.354 1.406,0.354 1.563,0.354 false 2.01,0.896 2.01,1.24 2.01,1.24 2.094,1.24 false 1.521,0.75 1.646,0.906 0.125,0.156 10 false D 1.781,0.74 1.906,0.896 0.125,0.156 10 false C 2.146,0.74 2.271,0.896 0.125,0.156 10 false B 2.417,0.74 2.542,0.896 0.125,0.156 10 false A 2.719,0.729 2.885,0.896 0.167,0.167 10 false *2 0.479,0.656 0.688,0.802 0.208,0.146 10 false *1 0.375,1.604 0.573,1.771 0.198,0.167 10 false *a 0.708,2.177 1.042,2.333 0.333,0.156 10 false FG1 2.156,1.167 2.323,1.313 0.167,0.146 10 false *4 0.906,0.76 1.031,0.917 0.125,0.156 10 false F 1.177,0.75 1.302,0.906 0.125,0.156 10 false E 1.594,0.281 1.781,0.448 0.188,0.167 10 false *3

Disconnect the front door wire RH connector from the No. 2 floor wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FG1-1 - Body ground Always 1 MΩ or higher
FG1-2 - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Side Airbag Sensor Assembly RH
*2 Rear Airbag Sensor RH
*3 Front Door Wire RH
*4 No. 2 Floor Wire
*a Front view of wire harness connector
(to No. 2 Floor Wire)



OK

REPLACE NO. 2 FLOOR WIRE

NG

REPLACE FRONT DOOR WIRE RH