Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM2090E _58 Vehicle Interior _060701 SUPPLEMENTAL RESTRAINT SYSTEMS _0297704 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1612  Front Airbag Sensor RH Lost Communication  B1613  Front Airbag Sensor RH Initialization  


DESCRIPTION

The front airbag sensor RH circuit consists of the airbag ECU assembly and front airbag sensor RH.

The front airbag sensor RH detects impacts to the vehicle and sends signals to the airbag ECU assembly to determine if the airbag should be deployed.

These DTCs are stored when a malfunction is detected in the front airbag sensor RH circuit.

DTC No. DTC Detection Condition Trouble Area
B1612
B1613
·

The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the front airbag sensor RH circuit.

·

Front airbag sensor RH malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor RH

·

Airbag ECU assembly



WIRING DIAGRAM

C244889E54
1.854,0.771 2.042,1.031 0.188,0.26 10 false 2 1.333,0.917 1.885,1.177 0.552,0.26 10 false BUSIN 1.854,1.927 2.063,2.177 0.208,0.25 10 false 1 1.333,2.094 1.865,2.354 0.531,0.26 10 false RTNIN 5.135,0.802 5.406,0.99 0.271,0.188 10 false 29 5.396,0.906 5.75,1.115 0.354,0.208 10 false +SR 5.125,1.958 5.479,2.177 0.354,0.219 10 false 27 3.417,0.906 3.792,1.146 0.375,0.24 10 false DA3 3.417,2.073 3.781,2.344 0.365,0.271 10 false DA3 5.396,2.073 5.813,2.313 0.417,0.24 10 false -SR 0.542,2.917 1.146,3.208 0.604,0.292 10 false A51 0.542,3.094 2.365,3.396 1.823,0.302 10 false Front Airbag Sensor RH 5.313,2.927 5.802,3.083 0.49,0.156 10 false D27 5.313,3.094 6.729,3.469 1.417,0.375 10 false Airbag ECU Assembly 3.521,0.708 3.708,0.969 0.188,0.26 10 false 2 3.5,1.865 3.708,2.115 0.208,0.25 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag ECU assembly and front airbag sensor RH. Also check that the connectors that link the engine room main wire and instrument panel wire are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag ECU assembly and front airbag sensor RH. Also disconnect the connectors that link the engine room main wire and instrument panel wire.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.




OK

2.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (OPEN)

NG

REPLACE WIRE HARNESS

2.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (OPEN)
a.
U146989E03
2.229,0.927 2.052,1.125 true 2.427,0.917 2.667,1.135 true 1.24,3.74 1.021,4.156 true 1.49,3.74 1.688,4.167 true 2.344,1.198 2.344,1.354 false 0.708,2.094 0.813,2.25 0.104,0.156 10 false F 1.021,2.094 1.146,2.25 0.125,0.156 10 false E 1.469,2.094 1.594,2.25 0.125,0.156 10 false D 1.625,2.094 1.75,2.25 0.125,0.156 10 false C 2.073,2.094 2.198,2.25 0.125,0.156 10 false B 2.385,2.094 2.51,2.25 0.125,0.156 10 false A 0.417,2.094 0.615,2.281 0.198,0.188 10 false *1 2.802,2.385 2.958,2.573 0.156,0.188 10 false *2 0.979,0.292 1.188,0.49 0.208,0.198 10 false *a 0.365,3.198 0.552,3.385 0.188,0.188 10 false *b 1.75,1.052 2.01,1.208 0.26,0.156 10 false -SR 2.698,1.052 3.021,1.208 0.323,0.156 10 false +SR 0.563,3.625 0.823,3.781 0.26,0.156 10 false A51 2.281,1.385 2.438,1.542 0.156,0.156 10 false *3 0.75,4.177 1.198,4.333 0.448,0.156 10 false RTNIN 1.458,4.177 1.906,4.333 0.448,0.156 10 false BUSIN 1.094,0.698 1.365,0.844 0.271,0.146 10 false D27

Connect the connectors that link the engine room main wire and instrument panel wire.


b.

Using a service wire, connect terminals 29 (+SR) and 27 (-SR) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A51-2 (BUSIN) - A51-1 (RTNIN) Always Below 1 Ω


Text in Illustration
*1 Front Airbag Sensor RH
*2 Airbag ECU Assembly
*3 Service Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Front Airbag Sensor RH)



OK

3.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT)

NG

7.CHECK INSTRUMENT PANEL WIRE (OPEN)
3.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT)
a.
U146987E02
1.198,2.365 0.885,2.792 true 1.448,2.365 1.646,2.802 true 0.667,0.615 0.771,0.771 0.104,0.156 10 false F 0.969,0.615 1.094,0.771 0.125,0.156 10 false E 1.417,0.615 1.542,0.771 0.125,0.156 10 false D 1.573,0.615 1.698,0.771 0.125,0.156 10 false C 2.021,0.615 2.146,0.771 0.125,0.156 10 false B 2.344,0.615 2.469,0.771 0.125,0.156 10 false A 0.354,0.604 0.542,0.781 0.188,0.177 10 false *1 2.76,0.875 2.927,1.052 0.167,0.177 10 false *2 0.198,1.708 0.406,1.875 0.208,0.167 10 false *a 0.448,2.219 0.708,2.375 0.26,0.156 10 false A51 0.635,2.823 1.083,2.979 0.448,0.156 10 false RTNIN 1.438,2.823 1.885,2.979 0.448,0.156 10 false BUSIN

Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A51-2 (BUSIN) - A51-1 (RTNIN) Always 1 MΩ or higher


Text in Illustration
*1 Front Airbag Sensor RH
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Front Airbag Sensor RH)



OK

4.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT TO B+)

NG

8.CHECK INSTRUMENT PANEL WIRE (SHORT)
4.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT TO B+)
a.
U146987E02
1.198,2.365 0.885,2.792 true 1.448,2.365 1.646,2.802 true 0.667,0.615 0.771,0.771 0.104,0.156 10 false F 0.969,0.615 1.094,0.771 0.125,0.156 10 false E 1.417,0.615 1.542,0.771 0.125,0.156 10 false D 1.573,0.615 1.698,0.771 0.125,0.156 10 false C 2.021,0.615 2.146,0.771 0.125,0.156 10 false B 2.344,0.615 2.469,0.771 0.125,0.156 10 false A 0.354,0.604 0.542,0.781 0.188,0.177 10 false *1 2.76,0.875 2.927,1.052 0.167,0.177 10 false *2 0.198,1.708 0.406,1.875 0.208,0.167 10 false *a 0.448,2.219 0.708,2.375 0.26,0.156 10 false A51 0.635,2.823 1.083,2.979 0.448,0.156 10 false RTNIN 1.438,2.823 1.885,2.979 0.448,0.156 10 false BUSIN

Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A51-2 (BUSIN) - Body ground Ignition switch ON Below 1 V
A51-1 (RTNIN) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Text in Illustration
*1 Front Airbag Sensor RH
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Front Airbag Sensor RH)



OK

5.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT TO GROUND)

NG

9.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
5.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT TO GROUND)
a.
U146987E02
1.198,2.365 0.885,2.792 true 1.448,2.365 1.646,2.802 true 0.667,0.615 0.771,0.771 0.104,0.156 10 false F 0.969,0.615 1.094,0.771 0.125,0.156 10 false E 1.417,0.615 1.542,0.771 0.125,0.156 10 false D 1.573,0.615 1.698,0.771 0.125,0.156 10 false C 2.021,0.615 2.146,0.771 0.125,0.156 10 false B 2.344,0.615 2.469,0.771 0.125,0.156 10 false A 0.354,0.604 0.542,0.781 0.188,0.177 10 false *1 2.76,0.875 2.927,1.052 0.167,0.177 10 false *2 0.198,1.708 0.406,1.875 0.208,0.167 10 false *a 0.448,2.219 0.708,2.375 0.26,0.156 10 false A51 0.635,2.823 1.083,2.979 0.448,0.156 10 false RTNIN 1.438,2.823 1.885,2.979 0.448,0.156 10 false BUSIN

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A51-2 (BUSIN) - Body ground Always 1 MΩ or higher
A51-1 (RTNIN) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Front Airbag Sensor RH
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Front Airbag Sensor RH)



OK

6.CHECK FRONT AIRBAG SENSOR RH

NG

10.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
6.CHECK FRONT AIRBAG SENSOR RH
a.
C238211E01
2.195,0.812 2.316,0.967 0.121,0.156 10 A 2.036,0.812 2.157,0.967 0.121,0.156 10 B 1.581,0.812 1.703,0.967 0.121,0.156 10 C 1.425,0.812 1.546,0.967 0.121,0.156 10 D 0.98,0.812 1.101,0.967 0.121,0.156 10 E 0.829,0.812 0.950,0.967 0.121,0.156 10 F 0.514,0.812 0.698,0.989 0.184,0.178 10 *1 2.585,1.092 2.752,1.238 0.167,0.146 10 *2

Connect the connector to the airbag ECU assembly.


b.

Interchange the front airbag sensor RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) battery terminal.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs B1612, B1613, B1617 and B1618 are not output. A
DTC B1617 or B1618 is output. B
DTC B1612 or B1613 is output. C


HINT:

Codes other than DTCs B1612, B1613, B1617 and B1618 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the front airbag sensor RH and LH to their original positions and connect the connectors.

Text in Illustration
*1 Front Airbag Sensor LH
*2 Airbag ECU Assembly



A

B

C

7.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.
U147044E02
1.948,0.813 1.76,1.021 true 2.135,0.802 2.333,1.031 true 2.052,1.083 2.052,1.281 false 1.25,2.427 1.25,2.688 false 1.833,2.292 1.833,1.896 1.833,1.896 1.677,1.896 false 1.49,1 1.75,1.156 0.26,0.156 10 false -SR 2.365,1.031 2.688,1.188 0.323,0.156 10 false +SR 0.802,0.552 1.073,0.708 0.271,0.156 10 false D27 0.656,0.167 0.865,0.323 0.208,0.156 10 false *a 1.99,1.292 2.146,1.448 0.156,0.156 10 false *5 0.792,2.271 0.896,2.427 0.104,0.156 10 false F 1.021,2.271 1.146,2.427 0.125,0.156 10 false E 1.365,2.26 1.49,2.417 0.125,0.156 10 false D 1.604,2.25 1.729,2.406 0.125,0.156 10 false C 1.958,2.26 2.083,2.417 0.125,0.156 10 false B 2.208,2.26 2.333,2.417 0.125,0.156 10 false A 1.51,1.833 1.677,1.99 0.167,0.156 10 false *4 1.198,2.698 1.385,2.854 0.188,0.156 10 false *3 0.375,2.25 0.583,2.406 0.208,0.156 10 false *1 2.677,2.49 2.885,2.646 0.208,0.156 10 false *2 0.365,3.656 0.656,3.813 0.292,0.156 10 false DA3 0.229,3.208 0.438,3.365 0.208,0.156 10 false *b

Disconnect the instrument panel wire connector from the engine room main wire.

HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DA3-2 - DA3-1 Always Below 1 Ω



c.

Disconnect the service wire from connector B.

Text in Illustration
*1 Front Airbag Sensor RH
*2 Airbag ECU Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*5 Service Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Engine Room Main Wire)



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

8.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.
U147045E02
1.25,0.792 1.25,1.052 false 1.854,0.646 1.854,0.25 1.854,0.25 1.698,0.25 false 0.781,0.635 0.885,0.792 0.104,0.156 10 false F 1.01,0.635 1.135,0.792 0.125,0.156 10 false E 1.365,0.635 1.49,0.792 0.125,0.156 10 false D 1.615,0.625 1.74,0.781 0.125,0.156 10 false C 1.969,0.625 2.094,0.781 0.125,0.156 10 false B 2.208,0.615 2.333,0.771 0.125,0.156 10 false A 0.375,0.542 0.552,0.719 0.177,0.177 10 false *1 2.719,0.854 2.885,1.031 0.167,0.177 10 false *2 1.51,0.177 1.667,0.333 0.156,0.156 10 false *4 1.167,1.073 1.365,1.229 0.198,0.156 10 false *3 0.219,1.719 0.417,1.906 0.198,0.188 10 false *a 0.438,2.198 0.729,2.354 0.292,0.156 10 false DA3

Disconnect the instrument panel wire connector from the engine room main wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DA3-2 - DA3-1 Always 1 MΩ or higher


Text in Illustration
*1 Front Airbag Sensor RH
*2 Airbag ECU Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Engine Room Main Wire)



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

9.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
U147045E02
1.25,0.792 1.25,1.052 false 1.854,0.646 1.854,0.25 1.854,0.25 1.698,0.25 false 0.781,0.635 0.885,0.792 0.104,0.156 10 false F 1.01,0.635 1.135,0.792 0.125,0.156 10 false E 1.365,0.635 1.49,0.792 0.125,0.156 10 false D 1.615,0.625 1.74,0.781 0.125,0.156 10 false C 1.969,0.625 2.094,0.781 0.125,0.156 10 false B 2.208,0.615 2.333,0.771 0.125,0.156 10 false A 0.375,0.542 0.552,0.719 0.177,0.177 10 false *1 2.719,0.854 2.885,1.031 0.167,0.177 10 false *2 1.51,0.177 1.667,0.333 0.156,0.156 10 false *4 1.167,1.073 1.365,1.229 0.198,0.156 10 false *3 0.219,1.719 0.417,1.906 0.198,0.188 10 false *a 0.438,2.198 0.729,2.354 0.292,0.156 10 false DA3

Disconnect the instrument panel wire connector from the engine room main wire.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
DA3-2 - Body ground Ignition switch ON Below 1 V
DA3-1 - Body ground Ignition switch ON Below 1 V


Text in Illustration
*1 Front Airbag Sensor RH
*2 Airbag ECU Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Engine Room Main Wire)



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

10.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
U147045E02
1.25,0.792 1.25,1.052 false 1.854,0.646 1.854,0.25 1.854,0.25 1.698,0.25 false 0.781,0.635 0.885,0.792 0.104,0.156 10 false F 1.01,0.635 1.135,0.792 0.125,0.156 10 false E 1.365,0.635 1.49,0.792 0.125,0.156 10 false D 1.615,0.625 1.74,0.781 0.125,0.156 10 false C 1.969,0.625 2.094,0.781 0.125,0.156 10 false B 2.208,0.615 2.333,0.771 0.125,0.156 10 false A 0.375,0.542 0.552,0.719 0.177,0.177 10 false *1 2.719,0.854 2.885,1.031 0.167,0.177 10 false *2 1.51,0.177 1.667,0.333 0.156,0.156 10 false *4 1.167,1.073 1.365,1.229 0.198,0.156 10 false *3 0.219,1.719 0.417,1.906 0.198,0.188 10 false *a 0.438,2.198 0.729,2.354 0.292,0.156 10 false DA3

Disconnect the instrument panel wire connector from the engine room main wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DA3-2 - Body ground Always 1 MΩ or higher
DA3-1 - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Front Airbag Sensor RH
*2 Airbag ECU Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Engine Room Main Wire)



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE