Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM2090E _58 Vehicle Interior _060704 HEATING / AIR CONDITIONING _0297734 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) U

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  TERMINALS OF ECU  


AIR CONDITIONING CONTROL ASSEMBLY


U190434E02
1.708,0.281 1.979,0.438 0.271,0.156 10 false D19 5.031,0.281 5.302,0.438 0.271,0.156 10 false D20

HINT:

Check from the rear of the connector while it is connected to the air conditioning control assembly.


Terminal No.
(Symbol)
Wiring Color Description Condition Specified Condition
D19-1 (ACC) - D19-16 (GND) R-B - B-Y Power source (ACC) Ignition switch : OFF Below 1 V
Ignition switch : ACC 10 to 16 V
D19-2 (PSW) - D20-6 (SG) Y-B - LG A/C pressure switch signal Engine running
A/C system operating
Refrigerant pressure: Normal
10 to 16 V
Engine running
A/C system operating
Refrigerant pressure: Abnormal
Below 1 V
D20-6 (SG) - Body ground B-Y - Body ground Ground for sensor and servo motor Always Below 1 Ω
D19-8 (HR) - D19-16 (GND) V-Y - B-Y Heater relay control signal Blower switch : OFF
Refrigerant, pressure: Normal
Below 1 V
Blower switch : ON
Refrigerant, pressure: Normal
10 to 16 V
D19-9 (+B) - D19-16 (GND) L-R - B-Y Power source (Back up) Always 10 to 16 V
D19-10 (IG) - D19-16 (GND) G - B-Y Power source (IG) Ignition switch : OFF Below 1 V
Ignition switch : IG 10 to 16 V
D19-11 (ILL+) - D19-16 (GND) V - B-Y Tail indication light signal Headlight switch : OFF Below 1 V
Headlight switch : TAIL 10 to 16 V
D19-12 (CANL) - D19-16 (GND) L-Y - B-Y CAN communication circuit Ignition switch : ON Pulse generation
D19-13 (CANH) - D19-16 (GND) L-W - B-Y CAN communication circuit Ignition switch : ON Pulse generation
D19-14 (BLW) - D19-16 (GND) G-W - B-Y Blower motor speed control signal Ignition switch : ON
Blower switch : ON
Pulse generation
(See waveform 1)
D20-2 (CLTS) - Body ground Y - Body ground A/C solar sensor signal Ignition switch : ON
Solar sensor is subjected to electric light.
0.8 to 4.3 V
D20-13 (S5) - D19-16 (GND) W - B-Y Power supply for sensor and servo motor Ignition switch : ON 4.75 to 5.25 V


COMBINATION METER


U190443E02
3.5,0.323 3.708,0.479 0.208,0.156 10 false D7

Terminal No.
(Symbol)
Wiring Color Description Condition Specified Condition
D7-24(TAM) - D7-25(SG-) L - W Ambient temperature sensor signal Ignition switch : ON
Ambient temperature at 25°C(77°F)
1.4 to 1.6 V
D7-6(CANL) - Body ground BR - Body ground CAN communication circuit Ignition switch : ON Pulse generation
D7-7(CANH) - Body ground BR-W - Body ground CAN communication circuit Ignition switch : ON Pulse generation


INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY, MAIN BODY ECU (NETWORK GATEWAY ECU)


U190438E02
3,0.667 3.229,0.823 0.229,0.156 10 false MB 2.698,2.719 2.927,2.875 0.229,0.156 10 false MB 2.927,3.75 3.135,3.906 0.208,0.156 10 false D5 3.49,3.75 3.698,3.906 0.208,0.156 10 false D6 2.833,4.542 3.042,4.698 0.208,0.156 10 false D5 5.135,4.542 5.344,4.698 0.208,0.156 10 false D6

a.

Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.


b.

Measure the values on the wire harness side with the connector disconnected.

CONNECTOR MB
Terminal No.
(Symbol)
Wiring Color Description Condition Specified Condition
MB8(IG) - Body ground - Power source (IG) Ignition switch : ON 11 to 14 V
MB9(ACC) - Body ground - Power source (ACC) Ignition switch : ACC 11 to 14 V
MB11(GND) - Body ground - Ground for main power supply Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Install the main body ECU (network gateway ECU) to the instrument panel junction block assembly.


d.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


MAIN BODY ECU (NETWORK GATEWAY ECU) D5
Terminal No.
(Symbol)
Wiring Color Description Condition Specified Condition
D5-13(CANL) - D5-14(CANH) LG - P CAN communication circuit Ignition switch : ON Pulse generation
D6-13(CLTE) - Body ground G - Body ground Ground for solar sensor Always Below 1 Ω
D6-15(CLTB) - Body ground R - Body ground Power supply for solar sensor Ignition switch : ON 4.75 to 5.25 V



ECM


U147278E03
5.469,0.323 5.74,0.469 0.271,0.146 10 false A33

Terminal No.
(Symbol)
Wiring Color Description Condition Specified Condition
A33-8(ACP) - Body ground G - Body ground Air conditioner pressure switch signal Engine running
A/C system operating
Refrigerant pressure: Abnormal
Below 1 V
Engine running
A/C system operating
Refrigerant pressure: Normal
10 to 16 V
A33-18(CANL) - A33-19(CANH) B-P - O CAN communication circuit Ignition switch : ON Pulse generation