Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM2090E _58 Vehicle Interior _060704 HEATING / AIR CONDITIONING _0297734 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) D

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  DIAGNOSIS SYSTEM  


DESCRIPTION


a.

Air conditioning system data and the Diagnostic Trouble Codes (DTCs) can be read through the Data Link Connector 3 (DLC3) of the vehicle. When the system seems to be malfunctioning, use the GTS to check for malfunctions and perform troubleshooting.




LIST OF OPERATION METHODS


a.

By operating each of the air conditioning control switches as shown in the diagram below, it is possible to enter diagnostic check mode.

E239341E02
0.469,0.323 3.083,1.177 2.615,0.854 10 false Turn the ignition switch to ON while pressing the A/C control assembly "AUTO" switch and "Recirculation/Fresh" switch simultaneously. Hold both switches until the indicator check screen appears. 1.063,2.646 2.448,3 1.385,0.354 10 false Indicator Check (continuous operation) 0.906,4.104 2.583,4.479 1.677,0.375 10 false Sensor Check (DTC check) (continuous operation) 0.896,5.719 2.583,6.083 1.688,0.365 10 false Sensor Check (DTC check) (step operation) 4.688,4.063 6.073,4.417 1.385,0.354 10 false Actuator Check (continuous operation) 4.802,5.688 5.833,6.052 1.031,0.365 10 false Actuator Check (step operation) 2.031,7.479 4.938,7.656 2.906,0.177 10 false Check mode is canceled and A/C control starts 3.792,1.198 6.438,1.552 2.646,0.354 10 false The "AUTO" and "Recirculation/Fresh" switches are not pressed at the same time. 0.76,8.156 2.448,8.344 1.688,0.188 10 false : Indicates switch operation



INDICATOR CHECK


a.

Turn the ignition switch off.


b.
E247459

Turn the ignition switch to ON while pressing the air conditioning control assembly "AUTO" switch and "Recirculation/Fresh" switch simultaneously. Hold both switches until the indicator check screen appears.


c.

The indicator check is automatically performed when panel diagnosis is activated. Check that the indicators light up and go off 4 times at 1 second intervals continuously.

E247461E02
0.177,0.531 0.354,0.729 0.177,0.198 10 false *a 0.333,1.385 0.51,1.552 0.177,0.167 10 false *b 0.323,2.042 0.5,2.208 0.177,0.167 10 false *c 1.073,0.896 1.25,1.083 0.177,0.188 10 false *d 1.396,0.885 1.583,1.052 0.188,0.167 10 false *d

Text in Illustration
*a Indicator Blinking Pattern
*b ON
*c OFF
*d 1 sec.

HINT:
·

The sensor check automatically starts when the indicator check is completed.

·

Press the "OFF" switch to cancel check mode.





SENSOR CHECK (DTC CHECK)


a.

Start the engine and warm it up.


b.

Perform the indicator check.

HINT:

After the indicator check is completed, the system enters DTC check mode automatically.



c.
E247465E02
2.042,0.948 3.021,1.667 true 3.052,1.594 3.219,1.781 0.167,0.188 10 false *a

Read the DTC displayed on the accessory meter display.

NOTICE:
·

In sensor check mode, which is automatically entered after indicator check mode, troubleshooting may be partially performed. Be sure to perform the sensor check again.

·

If the check is performed in a dark place, DTC 25 may be displayed even though the system is normal.



HINT:

Refer to DTC Chart for details of the codes (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>DIAGNOSTIC TROUBLE CODE CHART).

·

When there are no problems, DTC 20 is output.

·

As an example, the illustration shows that DTC 21 is output.



Text in Illustration
*a Diagnostic Trouble Code (DTC)


d.

If the DTCs are difficult to read because they change automatically , press the "A/C" switch to display the DTCs one at a time so that they can be read easily. The DTCs change step by step each time the "A/C" switch is pressed.

HINT:

Press the "OFF" switch to finish panel diagnosis.