Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM2090E _58 Vehicle Interior _060704 HEATING / AIR CONDITIONING _0297734 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1432/22  Open in Ambient Temperature Sensor Circuit  B1433/-22  Short in Ambient Temperature Sensor Circuit  


DESCRIPTION

The thermistor assembly is installed in the front part of the condenser to detect the ambient temperature and control the air conditioner. The thermistor assembly is connected to the combination meter assembly and detects fluctuations in the ambient temperature. This data is used for controlling the room temperature. The thermistor assembly sends a signal to the air conditioning control assembly via the combination meter assembly. The resistance of the thermistor assembly changes in accordance with the ambient temperature. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The combination meter assembly applies a voltage (5 V) to the thermistor assembly and reads voltage changes as changes in the resistance of the thermistor assembly. The combination meter assembly sends the read signal to the air conditioning control assembly via CAN communication.

DTC No. DTC Detection Condition Trouble Area
B1432/22 Open in ambient temperature sensor circuit
·

Ambient temperature sensor (thermistor assembly)

·

Harness or connector between ambient temperature sensor (thermistor assembly) and air conditioning control assembly

·

Air conditioning control assembly


B1433/-22 Short in ambient temperature Sensor circuit
·

Ambient temperature sensor (thermistor assembly)

·

Harness or connector between ambient temperature sensor (thermistor assembly) and air conditioning control assembly

·

Air conditioning control assembly



WIRING DIAGRAM

E248911E02
5.292,1.792 5.563,1.969 0.271,0.177 10 false D20 0.156,1.438 0.427,1.594 0.271,0.156 10 false A48 0.146,1.615 2.448,1.958 2.302,0.344 10 false AMBIENT TEMPERATURE SENSOR (THERMISTOR ASSEMBLY) 3.083,1.948 4.396,2.281 1.313,0.333 10 false COMBINATION METER ASSEMBLY 3.094,1.781 3.323,1.948 0.229,0.167 10 false D7 2.792,0.885 2.958,1.042 0.167,0.156 10 false 24 2.792,1.115 2.969,1.271 0.177,0.156 10 false 25 1.844,0.896 1.938,1.042 0.094,0.146 10 false 1 1.854,1.115 1.948,1.26 0.094,0.146 10 false 2 5.302,1.958 6.792,2.302 1.49,0.344 10 false AIR CONDITIONING CONTROL ASSEMBLY 0.708,2.427 2.438,2.615 1.729,0.188 10 false : CAN Communication Line 3.021,0.969 3.333,1.125 0.313,0.156 10 false TAM 3.021,1.198 3.292,1.375 0.271,0.177 10 false SG- 5.344,0.948 5.74,1.104 0.396,0.156 10 false CANL 5.344,1.198 5.771,1.354 0.427,0.156 10 false CANH 5.115,0.813 5.302,0.979 0.188,0.167 10 false 12 5.115,1.073 5.281,1.219 0.167,0.146 10 false 13 4.448,1.073 4.583,1.229 0.135,0.156 10 false 6 4.448,0.813 4.573,0.979 0.125,0.167 10 false 7 3.99,0.938 4.375,1.104 0.385,0.167 10 false CANL 3.99,1.188 4.396,1.354 0.406,0.167 10 false CANH

CAUTION / NOTICE / HINT

NOTICE:
·

The heater and air conditioning system uses the CAN communication system. First, carry out the check of CAN communication system in accordance with the "HOW TO PROCEED WITH TROUBLESHOOTING", and confirm that there are no problems with the communications system before proceeding with troubleshooting.

·

Errors with the combination meter assembly may affect this DTC. Prior to carrying out an inspection, inspect "Meter and gauge system" DTCs, and confirm that the combination meter assembly is normal.



PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


e.

Check the value(s) by referring to the table below.


Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Ambient Temp Sensor
(Ambi Temp Sens)
Ambient temperature sensor (thermistor assembly) /
Min: -40.00°C (-40.00°F)
Max: 80.00°C (176.00°F)
Actual ambient temperature displayed -

OK:

The display is as specified in the normal condition column.


Result:
Result Proceed to
OK (When troubleshooting according to the DTC) A
OK (When troubleshooting according to Problem Symptoms Table) B
NG C



A

2.CHECK FOR DTC

B

C

3.INSPECT AMBIENT TEMPERATURE SENSOR (THERMISTOR ASSEMBLY)
3.INSPECT AMBIENT TEMPERATURE SENSOR (THERMISTOR ASSEMBLY)
a.

Remove the ambient temperature sensor (thermistor assembly) (See page Vehicle Interior>HEATING / AIR CONDITIONING>AMBIENT TEMPERATURE SENSOR>REMOVAL).


b.

Inspect the ambient temperature sensor (thermistor assembly) (See page Vehicle Interior>HEATING / AIR CONDITIONING>AMBIENT TEMPERATURE SENSOR>INSPECTION).



OK

4.CHECK HARNESS AND CONNECTOR (AMBIENT TEMPERATURE SENSOR (THERMISTOR ASSEMBLY) - COMBINATION METER ASSEMBLY)

NG

REPLACE AMBIENT TEMPERATURE SENSOR (THERMISTOR ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (AMBIENT TEMPERATURE SENSOR (THERMISTOR ASSEMBLY) - COMBINATION METER ASSEMBLY)
a.

Disconnect the D7 conditioning meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A48-1 - D7-24(TAM) Always Below 1 Ω
A48-2 - D7-25(SG-) Always Below 1 Ω
A48-1 - Body ground Always 10 kΩ or higher
A48-2 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR