Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING PRESSURE SENSOR
RM2090E _58 Vehicle Interior _060704 HEATING / AIR CONDITIONING _0297749 AIR CONDITIONING PRESSURE SENSOR G

HEATING / AIR CONDITIONING  AIR CONDITIONING PRESSURE SENSOR  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 88790E 1.INSPECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY

a.

Check the wire harness.

i.

Disconnect the air conditioner tube and accessory assembly connector.


ii.
E246513E01
0.121,0.083 0.291,0.248 0.170,0.166 10 *a

Using an ohmmeter, measure the resistance of the wire harness side connector.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - Body ground Always Below 1 Ω
2 - 4 Ignition switch ON Below 1 Ω


Text in Illustration
*a Component without harness connected
(air conditioner tube and accessory assembly)



b.

Check the air conditioning pressure sensor.

i.

Install a manifold gauge set.


ii.
E254250E03
2.708,1.219 2.708,1.729 2.708,1.729 2.552,1.729 true 0.625,0.896 0.719,0.604 0.719,0.604 0.781,0.604 true 0.615,1.24 0.542,1.552 0.542,1.552 0.469,1.552 true 0.708,1.115 0.865,1.531 0.865,1.531 0.948,1.531 true 0.531,1.063 0.344,0.635 0.344,0.635 0.25,0.635 true 2.365,1.646 2.552,1.833 0.188,0.188 10 false *1 0.833,0.521 0.979,0.677 0.146,0.156 10 false 1 0.125,0.552 0.24,0.719 0.115,0.167 10 false 3 0.323,1.479 0.469,1.635 0.146,0.156 10 false 4 1,1.458 1.146,1.615 0.146,0.156 10 false 2

Apply pressure on the sensor as indicated in the table below, and check the resistance between the terminals.

Text in Illustration
*1 Sensor Part

Standard Resistance:

for HFC-134a (R134a):

Tester Connection Condition Specified Condition
1 - 4 0 kPa (No Pressure applied) 10 kΩ or higher
1 - 4 1520 kPa (15.5 kgf/cm2, 221 psi) Below 1 Ω
2 - 3 0 kPa (No Pressure applied) 10 kΩ or higher
2 - 3 22.5 kPa (0.23 kgf/cm2, 33.0 psi) or more and below 3140 kPa (32 kgf/cm2, 455 psi) Below 1 Ω
2 - 3 3140 kPa (32 kgf/cm2, 455 psi) or more 10 kΩ or higher


Standard Resistance:

for HFO-1234yf (R1234yf):

Tester Connection Condition Specified Condition
1 - 4 0 kPa (No Pressure applied) 10 kΩ or higher
1 - 4 1520 kPa (15.5 kgf/cm2, 221 psi) Below 1 Ω
2 - 3 0 kPa (No Pressure applied) 10 kΩ or higher
2 - 3 248 kPa (2.53 kgf/cm2, 36.5 psi) or more and below 2980 kPa (30.4 kgf/cm2, 438 psi) Below 1 Ω
2 - 3 2980 kPa (30.4 kgf/cm2, 438 psi) or more 10 kΩ or higher