Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR
RM2090E _59 Vehicle Exterior _060707 WINDOW / GLASS _0297761 POWER WINDOW REGULATOR MOTOR G

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR  INSPECTION  


CAUTION / NOTICE / HINT

HINT:

Use the same procedure for the LHD and RHD vehicles.


PROCEDURE

Hide 85710E 1.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

a.
B292925E02
2.354,1.344 2.802,0.625 true 2.26,1.323 0.75,1.74 true 1.958,3.385 2.427,2.854 true 1.5,3.375 1.188,2.854 true 2.813,0.417 2.969,0.583 0.156,0.167 10 false *1 0.385,2.865 0.542,3.031 0.156,0.167 10 false *c 1.094,2.01 1.25,2.177 0.156,0.167 10 false *b 0.688,1.198 0.844,1.365 0.156,0.167 10 false *a 2.49,2.75 2.76,2.917 0.271,0.167 10 false WU 0.906,2.729 1.177,2.896 0.271,0.167 10 false WD

Check the operation of the power window regulator motor assembly RH.

NOTICE:

Do not apply positive (+) battery voltage to any terminals other than terminal 1 or 3 to avoid damaging the pulse sensor inside the motor.


i.

Apply battery voltage to the power window regulator motor assembly RH and check the operation of the power window regulator motor assembly RH.



b.

Check that the motor gear rotates smoothly as follows:

Standard:
Measurement Condition Specified Condition
1.

Battery positive (+) → Terminal 3 (WD)

2.

Battery negative (-) → Terminals 1 (WU)


Motor gear rotates clockwise
1.

Battery positive (+) → Terminal 1 (WU)

2.

Battery negative (-) → Terminals 3 (WD)


Motor gear rotates counterclockwise


Text in Illustration
*1 Motor Gear
*a Clockwise
*b Counterclockwise
*c Component without harness connected
(Power Window Regulator Motor Assembly RH)

If the result is not as specified, replace the power window regulator motor assembly RH.


CAUTION:

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.



Hide 85720D 2.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

a.
B312537E02
1.146,1.323 2.635,1.708 true 1.042,1.354 0.333,0.646 true 1.969,3.438 2.385,2.938 true 1.5,3.385 1.156,2.885 true 0.219,0.469 0.375,0.625 0.156,0.156 10 false *1 2.635,1.292 2.792,1.448 0.156,0.156 10 false *a 2.417,1.969 2.573,2.125 0.156,0.156 10 false *b 0.146,2.885 0.302,3.042 0.156,0.156 10 false *c 2.458,2.813 2.719,2.969 0.26,0.156 10 false WU 0.969,2.719 1.229,2.875 0.26,0.156 10 false WD

Check the operation of the power window regulator motor assembly LH.

NOTICE:

Do not apply positive (+) battery voltage to any terminals other than terminal 1 or 3 to avoid damaging the pulse sensor inside the motor.


i.

Apply battery voltage to the power window regulator motor assembly LH and check the operation of the power window regulator motor assembly LH.



b.

Check that the motor gear rotates smoothly as follows:

Standard:
Measurement Condition Specified Condition
1.

Battery positive (+) → Terminal 3 (WD)

2.

Battery negative (-) → Terminals 1 (WU)


Motor gear rotates counterclockwise
1.

Battery positive (+) → Terminal 1 (WU)

2.

Battery negative (-) → Terminals 3 (WD)


Motor gear rotates clockwise


Text in Illustration
*1 Motor Gear
*a Counterclockwise
*b Clockwise
*c Component without harness connected
(Power Window Regulator Motor Assembly LH)

If the result is not as specified, replace the power window regulator motor assembly LH.


CAUTION:

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.