Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM2090E _59 Vehicle Exterior _060707 WINDOW / GLASS _0297766 POWER WINDOW CONTROL SYSTEM U

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  TERMINALS OF ECU  


POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


a.

Disconnect the E8*1 or F6*2 power window regulator master switch assembly connector.

*1: for LHD

*2: for RHD


U190275E02
2.073,0.646 2.396,0.917 0.323,0.271 10 false *A 1.76,0.646 2.052,0.875 0.292,0.229 10 false E8 2.083,1.031 2.406,1.302 0.323,0.271 10 false *B 1.76,1.031 2.052,1.26 0.292,0.229 10 false F6

Text in Illustration
*A for LHD *B for RHD


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
E8-12 (+B) - E8 - 5 (GND) SB - B Power supply Always 11 to 14 V
E8-5 (GND) - Body ground B - Body ground Ground Always Below 1 Ω

for RHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
F6-12 (+B) - F6-5 (GND) SB - B Power supply Always 11 to 14 V
F6-5 (GND) - Body ground B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the E8*1 or F6*2 power window regulator master switch assembly connector.

*1: for LHD

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
E8-6 (WU) - E8-5 (GND) W-B - B Power window motor UP output Ignition switch ON, power window regulator master switch OFF 11 to 14 V
Ignition switch ON, power window regulator master switch UP (Manual operation) Below 1 V
E8-6 (WU) - E8-5 (GND) W-B - B Power window motor AUTO UP output Ignition switch ON, driver side door power window fully open 11 to 14 V
Ignition switch ON, driver side door power window moving, power window regulator master switch assembly fully pulled UP (Automatic operation) Below 1 V
Ignition switch ON, driver side door power window fully closed 11 to 14 V
E8-7 (WD) - E8-5 (GND) LG - B Power window motor DOWN output Ignition switch ON, power window regulator master switch OFF 11 to 14 V
Ignition switch ON, power window regulator master switch DOWN (Manual operation) Below 1 V
E8-7 (WD) - E8-5 (GND) LG - B Power window motor AUTO DOWN output Ignition switch ON, driver side door power window fully open 11 to 14 V
Ignition switch ON, driver side door power window moving, power window regulator master switch assembly fully pushed DOWN (Automatic operation) Below 1 V
Ignition switch ON, driver side door power window fully closed 11 to 14 V
E8-8 (SN1) - E8-5 (GND) Y - B Hall IC in front power window regulator motor assembly LH input Ignition switch ON, power window regulator master switch assembly OFF → UP or DOWN Pulse generation (See waveform 1)
E8-1 (SN2) - E8-5 (GND) GR - B Hall IC in front power window regulator motor assembly LH input Ignition switch ON, power window regulator master switch assembly OFF → UP or DOWN Pulse generation (See waveform 1)

for RHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
F6-6 (WU) - F6-5 (GND) W-B - B Power window motor UP output Ignition switch ON, power window regulator master switch OFF 11 to 14 V
Ignition switch ON, power window regulator master switch UP (Manual operation) Below 1 V
F6-6 (WU) - F6-5 (GND) W-B - B Power window motor AUTO UP output Ignition switch ON, driver side door power window fully open 11 to 14 V
Ignition switch ON, driver side door power window moving, power window regulator master switch assembly fully pulled UP (Automatic operation) Below 1 V
Ignition switch ON, driver side door power window fully closed 11 to 14 V
F6-7 (WD) - F6-5 (GND) LG - B Power window motor DOWN output Ignition switch ON, power window regulator master switch OFF 11 to 14 V
Ignition switch ON, power window regulator master switch DOWN (Manual operation) Below 1 V
F6-7 (WD) - F6-5 (GND) LG - B Power window motor AUTO DOWN output Ignition switch ON, driver side door power window fully open 11 to 14 V
Ignition switch ON, driver side door power window moving, power window regulator master switch assembly fully pushed DOWN (Automatic operation) Below 1 V
Ignition switch ON, driver side door power window fully closed 11 to 14 V
F6-8 (SN1) - F6-5 (GND) Y - B Hall IC in front power window regulator motor assembly RH input Ignition switch ON, power window regulator master switch assembly OFF → UP or DOWN Pulse generation (See waveform 1)
F6-1 (SN2) - F6-5 (GND) GR - B Hall IC in front power window regulator motor assembly RH input Ignition switch ON, power window regulator master switch assembly OFF → UP or DOWN Pulse generation (See waveform 1)


e.
B399299E01
2.917,1.625 3.24,1.781 0.323,0.156 10 false GND 2.917,0.865 3.375,1.063 0.458,0.198 10 false GND 0.219,0.865 0.583,1.031 0.365,0.167 10 false CH1 0.208,1.604 0.594,1.75 0.385,0.146 10 false CH2

waveform 1

Measurement Condition
Item Content
Tester Connection CH1: E8-8 (SN1) - E8-5 (GND)*1
CH2: E8-1 (SN2) - E8-5 (GND)*1
CH1: F6-8 (SN1) - F6-5 (GND)*2
CH2 :F6-1 (SN2) - F6-5 (GND)*2
Tool Setting 5 V/DIV., 2 ms./DIV.
Condition Ignition switch ON, power window regulator master switch assembly OFF → UP or DOWN

*1: for LHD

*2: for RHD




CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY


a.

Disconnect the F6*1 or E8*2 power window regulator switch assembly connector.

*1: for LHD

*2: for RHD


U190276E02
2.115,1.021 2.406,1.25 0.292,0.229 10 false E8 2.115,0.698 2.406,0.927 0.292,0.229 10 false F6 2.448,0.698 2.74,0.927 0.292,0.229 10 false *A 2.448,1.031 2.74,1.26 0.292,0.229 10 false *B

Text in Illustration
*A for LHD *B for RHD


b.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
F6-12 (+B) - F6-5 (GND) SB - B Power supply Always 11 to 14 V
F6-5 (GND) - Body ground B - Body ground Ground Always Bellow 1 V

for RHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
E8-12 (+B) - E8-5 (GND) SB - B Power supply Always 11 to 14 V
E8-5 (GND) - Body ground B - Body ground Ground Always Bellow 1 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the F6*1 or E8*2 power window regulator switch assembly connector.

*1: for LHD

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
F6-6 (WU) - F6-5 (GND) W-B - B Power window motor UP output Ignition switch ON, power window regulator switch off 11 to 14 V
Ignition switch ON, power window regulator switch UP (Manual operation) Bellow 1 V
F6-6 (WU) - F6-5 (GND) W-B - B Power window motor AUTO UP output Ignition switch ON, front passenger side door power window fully open 11 to 14 V
Ignition switch ON, front passenger side door power window moving, power window regulator switch assembly fully pulled UP (Automatic operation) Bellow 1 V
Ignition switch ON, front passenger side door power window fully closed 11 to 14 V
F6-7 (WD) - F6-5 (GND) LG - B Power window motor DOWN output Ignition switch ON, power window regulator switch off 11 to 14 V
Ignition switch ON, power window regulator switch DOWN (Manual operation) Bellow 1 V
F6-7 (WD) - F6-5 (GND) LG - B Power window motor AUTO DOWN output Ignition switch ON, front passenger side door power window fully open 11 to 14 V
Ignition switch ON, front passenger side door power window moving, power window regulator switch assembly fully pulled DOWN (Automatic operation) Bellow 1 V
Ignition switch ON, front passenger side door power window fully closed 11 to 14 V
F6-8 (SN1) - F6-5 (GND) Y - B Hall IC in front power window regulator motor assembly RH input Ignition switch ON, power window regulator switch assembly OFF → UP or DOWN Pulse generation (See waveform 1)
F6-1 (SN2) - F6-5 (GND) GR - B Hall IC in front power window regulator motor assembly RH input Ignition switch ON, power window regulator switch assembly OFF → UP or DOWN Pulse generation (See waveform 1)

for RHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
E8-6 (WU) - E8-5 (GND) W-B - B Power window motor UP output Ignition switch ON, power window regulator switch off 11 to 14 V
Ignition switch ON, power window regulator switch UP (Manual operation) Bellow 1 V
E8-6 (WU) - E8-5 (GND) W-B - B Power window motor AUTO UP output Ignition switch ON, front passenger side door power window fully open 11 to 14 V
Ignition switch ON, front passenger side door power window moving, power window regulator switch assembly fully pulled UP (Automatic operation) Bellow 1 V
Ignition switch ON, front passenger side door power window fully closed 11 to 14 V
E8-7 (WD) - E8-5 (GND) LG - B Power window motor DOWN output Ignition switch ON, power window regulator switch off 11 to 14 V
Ignition switch ON, power window regulator switch DOWN (Manual operation) Bellow 1 V
E8-7 (WD) - E8-5 (GND) LG - B Power window motor AUTO DOWN output Ignition switch ON, front passenger side door power window fully open 11 to 14 V
Ignition switch ON, front passenger side door power window moving, power window regulator switch assembly fully pulled DOWN (Automatic operation) Bellow 1 V
Ignition switch ON, front passenger side door power window fully closed 11 to 14 V
E8-8 (SN1) - E8-5 (GND) Y - B Hall IC in front power window regulator motor assembly LH input Ignition switch ON, power window regulator switch assembly OFF → UP or DOWN Pulse generation (See waveform 1)
E8-1 (SN2) - E8-5 (GND) GR - B Hall IC in front power window regulator motor assembly LH input Ignition switch ON, power window regulator switch assembly OFF → UP or DOWN Pulse generation (See waveform 1)


e.
B399299E01
2.917,1.625 3.24,1.781 0.323,0.156 10 false GND 2.917,0.865 3.375,1.063 0.458,0.198 10 false GND 0.219,0.865 0.583,1.031 0.365,0.167 10 false CH1 0.208,1.604 0.594,1.75 0.385,0.146 10 false CH2

waveform 1

Item Content
Tester Connection CH1: F6-8 (SN1) - F6-5 (GND)*1
CH2: F6-1 (SN2) - F6-5 (GND)*1
CH1: E8-8 (SN1) - E8-5 (GND)*2
CH2: E8-1 (SN2) - E8-5 (GND)*2
Tool Setting 5 V/DIV., 2 ms./DIV.
Condition Ignition switch ON, power window regulator switch assembly OFF → UP or DOWN

*1: for LHD

*2: for RHD




CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY


a.

Disconnect the E5*1 or F1*2 power window regulator motor assembly (for driver side) connector.

*1: for LHD

*2: for RHD


U190277E02
2.625,0.677 2.917,0.927 0.292,0.25 10 false *A 2.302,0.688 2.625,0.896 0.323,0.208 10 false E5 2.635,1.031 2.927,1.281 0.292,0.25 10 false *B 2.302,1.021 2.625,1.229 0.323,0.208 10 false F1

Text in Illustration
*A for LHD *B for RHD


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
E5-5 (VCC) - E5-4 (SGD) W - R Power supply Always 11 to 14 V
E5-4 (SGD) - Body ground R - Body ground Ground Always Below 1 Ω

for RHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
F1-5 (VCC) - F1-4 (SGD) W - R Power supply Always 11 to 14 V
F1-4 (SGD) - Body ground R - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the E5*1 or F1*2 power window regulator motor assembly (for driver side) connector.

*1: for LHD

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
E5-1 (WU) - E5-4 (SGD) W-B - R Power window motor UP input Ignition switch ON, power window regulator master switch off 11 to 14 V
Ignition switch ON, power window regulator master switch UP (Manual operation) Below 1 V
E5-1 (WU) - E5-4 (SGD) W-B - R Power window motor AUTO UP input Ignition switch ON, driver side door power window fully open 11 to 14 V
Ignition switch ON, driver side door power window moving, power window regulator master switch assembly fully pulled UP (Automatic operation) Below 1 V
Ignition switch ON, driver side door power window fully closed 11 to 14 V
E5-3 (WD) - E5-4 (SGD) LG - R Power window motor DOWN input Ignition switch ON, power window regulator master switch OFF 11 to 14 V
Ignition switch ON, power window regulator master switch DOWN (Manual operation) Below 1 V
E5-3 (WD) - E5-4 (SGD) LG - R Power window motor AUTO UP input Ignition switch ON, driver side door power window fully open 11 to 14 V
Ignition switch ON, driver side door power window moving, power window regulator master switch assembly fully pulled DOWN (Automatic operation) Below 1 V
Ignition switch ON, driver side door power window fully closed 11 to 14 V

for RHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
F1-1 (WU) - F1-4 (SGD) W-B - R Power window motor UP input Ignition switch ON, power window regulator master switch off 11 to 14 V
Ignition switch ON, power window regulator master switch UP (Manual operation) Below 1 V
F1-1 (WU) - F1-4 (SGD) W-B - R Power window motor AUTO UP input Ignition switch ON, driver side door power window fully open 11 to 14 V
Ignition switch ON, driver side door power window moving, power window regulator master switch assembly fully pulled UP (Automatic operation) Below 1 V
Ignition switch ON, driver side door power window fully closed 11 to 14 V
F1-3 (WD) - F1-4 (SGD) LG - R Power window motor DOWN input Ignition switch ON, power window regulator master switch OFF 11 to 14 V
Ignition switch ON, power window regulator master switch DOWN (Manual operation) Below 1 V
F1-3 (WD) - F1-4 (SGD) LG - R Power window motor AUTO UP input Ignition switch ON, driver side door power window fully open 11 to 14 V
Ignition switch ON, driver side door power window moving, power window regulator master switch assembly fully pulled DOWN (Automatic operation) Below 1 V
Ignition switch ON, driver side power window fully closed 11 to 14 V

If the result is not as specified, the power window regulator motor assembly (for driver side) may have a malfunction.



CHECK MAIN BODY ECU (NETWORK GATEWAY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


U146880E02
0.313,0.292 0.531,0.5 0.219,0.208 10 false *1 1.677,6.667 1.906,6.875 0.229,0.208 10 false *2 0.49,1.229 0.896,1.469 0.406,0.24 10 false 3D 0.49,1.875 0.896,2.115 0.406,0.24 10 false 3C 0.49,2.396 0.896,2.635 0.406,0.24 10 false 3E 3.729,1.052 4.135,1.292 0.406,0.24 10 false MB 3.479,3.198 3.885,3.438 0.406,0.24 10 false MB 6.333,1.229 6.74,1.469 0.406,0.24 10 false 3B 6.333,1.865 6.74,2.104 0.406,0.24 10 false 3A 1.469,4.073 1.875,4.313 0.406,0.24 10 false 3D 4.177,4.073 4.583,4.313 0.406,0.24 10 false 3C 4.906,5.281 5.313,5.521 0.406,0.24 10 false 3A 3.052,6.552 3.458,6.792 0.406,0.24 10 false A73 3.677,6.552 4.01,6.792 0.333,0.24 10 false D5 4.26,6.552 4.594,6.792 0.333,0.24 10 false D6 1.802,5.281 2.208,5.521 0.406,0.24 10 false 3B 6.25,4.073 6.656,4.313 0.406,0.24 10 false 3E 1.177,7.521 1.583,7.76 0.406,0.24 10 false A73 3.563,7.521 3.896,7.76 0.333,0.24 10 false D5 5.875,7.521 6.208,7.76 0.333,0.24 10 false D6

Text in illustration
*1 Instrument Panel Junction Block Assembly *2 Main Body ECU (Network Gateway ECU)

a.

Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
MB-1 (BECU) - Body ground None - Body ground Battery power supply Always 11 to 14 V
MB-8 (IG) - Body ground None - Body ground Ignition switch power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
MB-9 (ACC) - Body ground None - Body ground ACC power supply Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
MB-11 (GND) - Body ground None - Body ground Ground Always Below 1 Ω
MB-32 (+B) - Body ground None - Body ground Battery power supply Always 11 to 14 V

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Disconnect the D5 main body ECU (network gateway ECU) connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. Wiring Color Terminal Description Condition Specified Condition
D5-22 (ACC)* - Body ground W - Body ground ACC power supply Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V

*: w/ Entry and Start System



e.

Reinstall the main body ECU (network gateway ECU).


f.

Measure the voltage of the wire harness side connectors.

for LHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
3B-13 (FPCY) - Body ground GR - Body ground Front door courtesy light switch RH input Front door RH open Below 1 V
Front door RH closed 11 to 14 V
3A-28 (FDCY) - Body ground V - Body ground Front door courtesy light switch LH input Front door LH open Below 1 V
Front door LH closed 11 to 14 V
D5-4 - Body ground LG - Body ground LIN communication signal Ignition switch ON Pulse generation

for RHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
3B-13 (FPCY) - Body ground GR - Body ground Front door courtesy light switch LH input Front door LH open Below 1 V
Front door LH closed 11 to 14 V
3A-28 (FDCY) - Body ground V - Body ground Front door courtesy light switch RH input Front door RH open Below 1 V
Front door RH closed 11 to 14 V
D5-4 - Body ground LG - Body ground LIN communication signal Ignition switch ON Pulse generation

If the result is not as specified, the main body ECU (network gateway ECU) or instrument panel junction block assembly may have a malfunction.