Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR
RM2090E _59 Vehicle Exterior _060708 DOOR / HATCH _0297771 FRONT DOOR N

DOOR / HATCH  FRONT DOOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

B228782E01
2.455,0.051 2.648,0.198 0.193,0.147 10 *2 0.817,0.051 1.010,0.198 0.193,0.147 10 *1

HINT:
·

Use the same procedure for both the RH and LH sides.

·

The following procedure is for the LH side.

·

Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed on it. Substitute the centering bolts with standard bolts when making adjustments.

·

Specified torque for standard bolts is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



Text in Illustration
*1 Centering Bolt
*2 Standard Bolt

PROCEDURE

Hide 1.INSPECT FRONT DOOR

a.

Check that the clearance measurements of areas *a through *j are within each standard range.

B309230E01
0.371,0.386 1.688,0.592 1.317,0.206 10 *1 0.365,4.203 1.682,4.409 1.317,0.206 10 *2 1.916,1.167 2.073,1.318 0.157,0.151 10 *a 5.781,1.398 5.964,1.593 0.184,0.195 10 *e 3.604,1.29 3.788,1.485 0.184,0.195 10 *d 3.771,0.468 3.954,0.663 0.184,0.195 10 *c 2.611,1.423 2.794,1.618 0.184,0.195 10 *b 6.385,4.647 6.569,4.842 0.184,0.195 10 *g 5.939,5.206 6.122,5.360 0.184,0.155 10 *f 4.533,4.938 4.694,5.088 0.161,0.150 10 *h 1.883,4.782 2.009,4.975 0.126,0.193 10 *j 2.2,5.159 2.361,5.309 0.161,0.150 10 *i

Standard Clearance
Area Measurement Area Measurement
*a 0.5 mm (0.0197 in.) *b 7.0 mm (0.2756 in.)
*c 5.0 mm (0.1969 in.) *d 6.7 mm (0.2638 in.)
*e 13.5 to 16.5 mm (0.5315 to 0.6496 in.) *f 2.5 to 5.5 mm (0.0984 to 0.2165 in.)
*g 0.0 to 1.5 mm (0.0 to 0.0591 in.) *h 4.8 to 7.8 mm (0.1890 to 0.3071 in.)
*i 3.1 to 5.6 mm (0.122 to 0.220 in.) *j -1.0 to 1.5 mm (-0.0394 to 0.0591 in.)

Text in Illustration
*1 Front Glass *2 Front Door


Hide 2.ADJUST FRONT DOOR GLASS

a.
B422182E03
2.76,0.667 3.094,0.417 true 2.271,1.094 2.51,1.271 0.24,0.177 10 false b 2.135,0.354 2.375,0.531 0.24,0.177 10 false a 3,0.24 3.302,0.385 0.302,0.146 10 false SST 0.896,0.292 1.135,0.469 0.24,0.177 10 false *a

Insert SST as shown in the illustration.

SST
09812-18010  


b.

Using SST, check that the clearance measurements of areas "a" and "b" are within each standard range.

SST
09812-18010  

Standard Clearance:
Area Measurement
a 5.0 mm (0.1969 in.)
b 6.7 mm (0.2638 in.)


Text in Illustration
*a 400 mm (15.7 in.)


c.
B312234

Adjust the front door glass so that the fitting dimensions come within the reference values.


d.

Loosen the nuts on the front door sash stopper and front door rear sash stopper, and adjust the glass position.


e.

After the adjustment, tighten the nuts on the front door sash stopper and front door rear sash stopper.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


f.
B312235

Loosen the 2 nuts on the front door rear lower frame sub-assembly, and adjust the glass position.


g.

After the adjustment, tighten the 2 nuts on the front door rear lower frame sub-assembly.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


h.
B422183

Loosen the bolt on the door glass inner stabilizer.


i.
B422184

Loosen the 2 nuts on the front door rear lower frame sub-assembly.


j.

Using a screwdriver, rotate the bolts and then adjust the position of the front door glass in lateral direction.


k.

After the adjustment, tighten the 2 nuts on the front door rear lower frame sub-assembly.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


l.
B422185E02
3.156,0.281 3.354,0.458 0.198,0.177 10 false *a

Tighten the bolt on the door glass inner stabilizer.

i.

Lower the front door glass approximately 20.0 mm (0.7874 in.).

Text in Illustration
*a 20.0 mm (0.7874 in.)


ii.

Push the front door glass toward the outside of the vehicle.


iii.

While pushing the front door glass and the door glass inner stabilizer toward the outside of the vehicle, tighten the bolt on the door glass inner stabilizer.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)



m.
B370942E04
1.854,1.229 2.281,0.667 true 1.302,1.406 1.448,1.583 0.146,0.177 10 false a 1.917,2.042 2.073,2.198 0.156,0.156 10 false b 2.365,0.552 2.677,0.708 0.313,0.156 10 false SST

Using SST, check that the clearance measurements of areas "a" and "b" are within each standard range.

SST
09812-18020  

Standard Clearance:
Area Measurement
a 2.5 to 5.5 mm (0.0984 to 0.2165 in.)
b 5.2 to 8.2 mm (0.2047 to 0.3228 in.)



n.
B312236

Adjust the front door sush so that the fitting dimensions come within the reference values.


o.

Loosen the nut on the front door sush and adjust the front door sash position.


p.

After the adjustment, tighten the nut on the front door sush.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide 3.ADJUST FRONT DOOR

a.
B359232

Loosen the hinge bolts on the vehicle body and adjust the door position.


b.

Loosen the hinge bolts on the door and adjust the door position.


c.

After the adjustment, tighten the hinge bolts on the door.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


d.
B309232

Adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.


e.

After the adjustment, tighten the striker mounting screws.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)