Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR
RM2090E _59 Vehicle Exterior _060709 MIRROR (EXT) _0297780 OUTER REAR VIEW MIRROR G

MIRROR (EXT)  OUTER REAR VIEW MIRROR  INSPECTION  


PROCEDURE

Hide 87901B 1.INSPECT OUTER REAR VIEW MIRROR SUB-ASSEMBLY RH

a.

Check the operation of the mirror surface.

i.
B312532E02
2.375,2.51 2.531,2.146 true 2.021,2.51 1.729,2.125 true 2.313,2.906 2.448,3.146 true 1.823,2.927 1.885,3.135 true 1.531,2.885 1.229,3.115 true 0.406,1.823 0.594,1.979 0.188,0.156 10 false *a 2.542,1.948 2.635,2.104 0.094,0.156 10 false + 2.479,3.135 2.563,3.292 0.083,0.156 10 false - 1.51,1.896 1.833,2.052 0.323,0.156 10 false MR+ 1.792,3.167 2.031,3.323 0.24,0.156 10 false MV 1.042,3.146 1.281,3.302 0.24,0.156 10 false MH

Disconnect the outer rear view mirror sub-assembly RH connector.


ii.

Apply battery voltage and check the operation of the mirror.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 3 (MR+)
Battery negative (-) → Terminal 8 (MV)
Turns upward
Battery positive (+) → Terminal 8 (MV)
Battery negative (-) → Terminal 3 (MR+)
Turns downward
Battery positive (+) → Terminal 7 (MH)
Battery negative (-) → Terminal 3 (MR+)
Turns left
Battery positive (+) → Terminal 3 (MR+)
Battery negative (-) → Terminal 7 (MH)
Turns right


Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Sub-assembly RH)

If the result is not as specified, replace the outer rear view mirror sub-assembly RH.



b.

Check the operation of the retractable mirror (w/ Mirror Retract Switch).

NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.

·

The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.



i.
B312531E02
1.344,3.583 1.604,3.125 true 2.281,3.573 2.531,3.125 true 1.344,4.01 1.604,4.271 true 2.313,4.01 2.563,4.271 true 2,0.063 2.198,0.219 0.198,0.156 10 false *a 2.365,0.969 2.563,1.125 0.198,0.156 10 false *b 2.219,1.781 2.417,1.938 0.198,0.156 10 false *c 1.813,2.042 2.01,2.198 0.198,0.156 10 false *d 1.406,2.25 1.604,2.406 0.198,0.156 10 false *e 0.719,2.771 0.917,2.927 0.198,0.156 10 false *f 1.646,2.979 1.969,3.135 0.323,0.156 10 false MFR 1.646,4.24 1.99,4.396 0.344,0.156 10 false MRR 2.573,2.979 2.688,3.135 0.115,0.156 10 false + 2.635,4.219 2.719,4.375 0.083,0.156 10 false -

Disconnect the outer rear view mirror sub-assembly RH connector.


ii.

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

OK:
Tester Connection Condition Specified Condition
Battery positive (+) → Terminal 2 (MFR)
Battery negative (-) → Terminal 6 (MRR)
Forward position (A) Moves from (A) to retracted position (E)
Battery positive (+) → Terminal 6 (MRR)
Battery negative (-) → Terminal 2 (MFR)
Forward position (A) Does not move
Battery positive (+) → Terminal 2 (MFR)
Battery negative (-) → Terminal 6 (MRR)
Position between forward position (A) and driving position (C) Moves from (B) to retracted position (E)
Battery positive (+) → Terminal 6 (MRR)
Battery negative (-) → Terminal 2 (MFR)
Position between forward position (A) and driving position (C) Moves from (B) to forward position (A)
Battery positive (+) → Terminal 2 (MFR)
Battery negative (-) → Terminal 6 (MRR)
Driving position (C) Moves from (C) to retracted position (E)
Battery positive (+) → Terminal 6 (MRR)
Battery negative (-) → Terminal 2 (MFR)
Driving position (C) Does not move
Battery positive (+) → Terminal 2 (MFR)
Battery negative (-) → Terminal 6 (MRR)
Position between driving position (C) and retracted position (E) Moves from (D) to retracted position (E)
Battery positive (+) → Terminal 6 (MRR)
Battery negative (-) → Terminal 2 (MFR)
Position between driving position (C) and retracted position (E) Moves from (D) to driving position (C)
Battery positive (+) → Terminal 2 (MFR)
Battery negative (-) → Terminal 6 (MRR)
Retracted position (E) Does not move
Battery positive (+) → Terminal 6 (MRR)
Battery negative (-) → Terminal 2 (MFR)
Retracted position (E) Moves from (E) to driving position (C)


Text in Illustration
*a (A) Forward Position
*b (B)
*c (C) Driving position
*d (D)
*e (E) Retracted Position
*f Component without harness connected
(Outer Rear View Mirror Sub-assembly RH)

If the result is not as specified, replace the outer rear view mirror sub-assembly RH.



c.

Check the operation of the mirror heater (w/ Mirror Heater).

i.

Disconnect the outer rear view mirror sub-assembly RH connector.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (+) - 10 (-) 25°C (75°F) 9.6 to 14.4 Ω


If the result is not as specified, replace the outer rear view mirror sub-assembly RH.


ii.

Connect the cable from the positive (+) terminal to terminal 4 (+) and the negative battery (-) terminal to terminal 10 (-), then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, replace the outer rear view mirror sub-assembly RH.



Hide 87906B 2.INSPECT OUTER REAR VIEW MIRROR SUB-ASSEMBLY LH

a.

Check the operation of the mirror surface.

i.
B312534E02
2.313,2.906 2.469,3.135 true 2.333,2.49 2.479,2.167 true 2.021,2.51 1.823,2.146 true 1.823,2.917 1.823,3.135 true 1.542,2.896 1.313,3.125 true 0.635,1.75 0.823,1.906 0.188,0.156 10 false *a 2.51,3.115 2.594,3.25 0.083,0.135 10 false - 2.469,1.969 2.573,2.115 0.104,0.146 10 false + 1.646,1.917 1.948,2.073 0.302,0.156 10 false ML+ 1.167,3.135 1.406,3.292 0.24,0.156 10 false MH 1.719,3.156 1.958,3.313 0.24,0.156 10 false MV

Disconnect the outer rear view mirror sub-assembly LH connector.


ii.

Apply battery voltage and check the operation of the mirror.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 3 (ML+)
Battery negative (-) → Terminal 8 (MV)
Turns upward
Battery positive (+) → Terminal 8 (MV)
Battery negative (-) → Terminal 3 (ML+)
Turns downward
Battery positive (+) → Terminal 7 (MH)
Battery negative (-) → Terminal 3 (ML+)
Turns left
Battery positive (+) → Terminal 3 (ML+)
Battery negative (-) → Terminal 7 (MH)
Turns right


Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Sub-assembly LH)

If the result is not as specified, replace the outer rear view mirror sub-assembly LH.



b.

Check the operation of the retractable mirror (w/ Mirror Retract Switch).

NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.

·

The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.



i.
B312533E02
1.333,3.583 1.583,3.125 true 1.344,4.01 1.563,4.302 true 2.313,3.573 2.563,3.115 true 2.323,4 2.542,4.292 true 1.26,0 1.448,0.156 0.188,0.156 10 false *a 0.76,2.708 0.948,2.865 0.188,0.156 10 false *f 1.875,2.26 2.063,2.417 0.188,0.156 10 false *e 1.438,2.042 1.625,2.198 0.188,0.156 10 false *d 1.042,1.771 1.229,1.927 0.188,0.156 10 false *c 0.896,0.865 1.083,1.021 0.188,0.156 10 false *b 1.625,2.969 1.927,3.125 0.302,0.156 10 false MFL 1.625,4.25 1.948,4.406 0.323,0.156 10 false MRL 2.604,3 2.719,3.156 0.115,0.156 10 false + 2.604,4.229 2.698,4.385 0.094,0.156 10 false -

Disconnect the outer rear view mirror sub-assembly LH connector.


ii.

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

OK:
Tester Connection Condition Specified Condition
Battery positive (+) → Terminal 2 (MFL)
Battery negative (-) → Terminal 6 (MRL)
Forward position (A) Moves from (A) to retracted position (E)
Battery positive (+) → Terminal 6 (MRL)
Battery negative (-) → Terminal 2 (MFL)
Forward position (A) Does not move
Battery positive (+) → Terminal 2 (MFL)
Battery negative (-) → Terminal 6 (MRL)
Position between forward position (A) and driving position (C) Moves from (B) to retracted position (E)
Battery positive (+) → Terminal 6 (MRL)
Battery negative (-) → Terminal 2 (MFL)
Position between forward position (A) and driving position (C) Moves from (B) to forward position (A)
Battery positive (+) → Terminal 2 (MFL)
Battery negative (-) → Terminal 6 (MRL)
Driving position (C) Moves from (C) to retracted position (E)
Battery positive (+) → Terminal 6 (MRL)
Battery negative (-) → Terminal 2 (MFL)
Driving position (C) Does not move
Battery positive (+) → Terminal 2 (MFL)
Battery negative (-) → Terminal 6 (MRL)
Position between driving position (C) and retracted position (E) Moves from (D) to retracted position (E)
Battery positive (+) → Terminal 6 (MRL)
Battery negative (-) → Terminal 2 (MFL)
Position between driving position (C) and retracted position (E) Moves from (D) to driving position (C)
Battery positive (+) → Terminal 2 (MFL)
Battery negative (-) → Terminal 6 (MRL)
Retracted position (E) Does not move
Battery positive (+) → Terminal 66 (MRL)
Battery negative (-) → Terminal 2 (MFL)
Retracted position (E) Moves from (E) to driving position (C)


Text in Illustration
*a (A) Forward Position
*b (B)
*c (C) Driving position
*d (D)
*e (E) Retracted Position
*f Component without harness connected
(Outer Rear View Mirror Sub-assembly LH)

If the result is not as specified, replace the outer rear view mirror sub-assembly LH.



c.

Check the operation of the mirror heater (w/ Mirror Heater).

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (+) - 10 (-) 25°C (75°F) 9.6 to 14.4 Ω


If the result is not as specified, replace the outer rear view mirror sub-assembly LH.


ii.

Connect the cable from the positive (+) terminal to terminal 4 (+) and the negative battery (-) terminal to terminal 10 (-), then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, replace the outer rear view mirror sub-assembly LH.