Home › Vehicle Exterior › MIRROR (EXT) › OUTER MIRROR SWITCH
RM2090E _59 Vehicle Exterior _060709 MIRROR (EXT) _0297782 OUTER MIRROR SWITCH G

MIRROR (EXT)  OUTER MIRROR SWITCH  INSPECTION  


PROCEDURE

Hide 84870A 1.INSPECT OUTER MIRROR SWITCH ASSEMBLY (for RHD)

a.
B310943E02
2.604,0.479 2.125,1.125 true 0.833,0.51 1.094,1.094 true 1.896,2.177 1.896,1.656 true 0.927,3.188 0.365,2.667 true 2.833,2.656 2.406,3.188 true 2.375,2.677 2.229,3.167 true 1.969,3.156 1.802,2.656 true 1.323,3.146 1.271,2.667 true 1.115,3.167 0.781,2.667 true 1.313,3.677 0.469,4.198 true 1.667,3.688 1.021,4.188 true 1.844,3.677 1.479,4.188 true 2.021,3.688 1.927,4.198 true 2.24,3.688 2.458,4.198 true 2.427,3.667 2.875,4.177 true 0.094,0.104 0.25,0.26 0.156,0.156 10 false *a 1.802,2.198 1.958,2.354 0.156,0.156 10 false *2 0.698,0.292 0.854,0.448 0.156,0.156 10 false *3 2.583,0.292 2.74,0.448 0.156,0.156 10 false *1 0.229,2.458 0.354,2.615 0.125,0.156 10 false E 2.844,2.469 2.969,2.625 0.125,0.156 10 false B 0.552,2.458 0.885,2.615 0.333,0.156 10 false MFR 1.125,2.458 1.458,2.615 0.333,0.156 10 false MFL 1.646,2.458 1.979,2.615 0.333,0.156 10 false MRR 2.229,2.458 2.563,2.615 0.333,0.156 10 false MRL 0.281,4.219 0.583,4.375 0.302,0.156 10 false ML+ 2.844,4.229 3.073,4.385 0.229,0.156 10 false HL 0.802,4.229 1.135,4.385 0.333,0.156 10 false MR+ 1.344,4.229 1.563,4.385 0.219,0.156 10 false VR 1.833,4.24 2.031,4.396 0.198,0.156 10 false VL 2.354,4.229 2.583,4.385 0.229,0.156 10 false HR

Check the switch functions.

i.

Turn the mirror select switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*1 Mirror Select Switch
*2 Mirror Surface Adjust Switch
*3 Mirror Retract Switch
*a Component without harness connected
(Outer Mirror Switch Assembly)

Standard Resistance (for left side):
Tester Connection Switch Condition Specified Condition
1 (B) - 14 (ML+)
10 (VL) - 7 (E)
UP Below 1 Ω
1 (B) - 10 (VL)
14 (ML+) - 7 (E)
DOWN Below 1 Ω
1 (B) - 8 (HL)
14 (ML+) - 7 (E)
LEFT Below 1 Ω
1 (B) - 14 (ML+)
8 (HL) - 7 (E)
RIGHT Below 1 Ω



iii.

Turn the mirror select switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):
Tester Connection Switch Condition Specified Condition
1 (B) - 12 (MR+)
11 (VR)- 7 (E)
UP Below 1 Ω
1 (B) - 11 (VR)
12 (MR+) - 7 (E)
DOWN Below 1 Ω
1 (B) - 9 (HR)
12 (MR+) - 7 (E)
LEFT Below 1 Ω
1 (B) - 12 (MR+)
9 (HR) - 7 (E)
RIGHT Below 1 Ω


If the result is not as specified, replace the outer mirror switch assembly.



b.

Check the mirror retract switch. (w/ Mirror Retract Switch)

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (B) - 6 (MFR)
3 (MRR) - 7 (E)
Mirror retract switch retract position Below 1 Ω
1 (B) - 3 (MRR)
6 (MFR) - 7 (E)
Mirror retract switch return position


If the result is not as specified, replace the outer mirror switch assembly.



Hide 84870A 2.INSPECT OUTER MIRROR SWITCH ASSEMBLY (for LHD)

a.
U190266E02
1.292,1.156 1.292,0.448 1.292,0.448 0.792,0.448 true 1.479,1.677 1.479,2.177 1.479,2.177 1.646,2.177 true 0.917,3.177 0.448,2.656 true 1.094,3.167 0.875,2.667 true 1.344,3.156 1.438,2.677 true 2.01,3.156 2.01,2.667 true 2.24,3.167 2.542,2.677 true 2.417,3.177 2.969,2.688 true 2.427,3.667 2.99,4.177 true 2.25,3.677 2.521,4.188 true 2.021,3.677 2.031,4.177 true 1.854,3.688 1.563,4.188 true 1.656,3.688 1.031,4.188 true 1.323,3.688 0.5,4.198 true 0.083,0.073 0.25,0.229 0.167,0.156 10 false *a 1.698,2.094 1.865,2.25 0.167,0.156 10 false *2 2.698,0.313 2.865,0.469 0.167,0.156 10 false *3 0.604,0.365 0.771,0.521 0.167,0.156 10 false *1 0.354,2.458 0.469,2.615 0.115,0.156 10 false E 2.99,2.469 3.104,2.625 0.115,0.156 10 false B 0.688,2.458 1.01,2.615 0.323,0.156 10 false MFR 1.313,2.458 1.635,2.615 0.323,0.156 10 false MFL 1.854,2.458 2.188,2.615 0.333,0.156 10 false MRR 2.427,2.458 2.76,2.615 0.333,0.156 10 false MRL 0.302,4.208 0.615,4.365 0.313,0.156 10 false ML+ 2.958,4.198 3.167,4.354 0.208,0.156 10 false HL 0.865,4.208 1.188,4.365 0.323,0.156 10 false MR+ 1.438,4.219 1.677,4.375 0.24,0.156 10 false VR 1.958,4.219 2.146,4.375 0.188,0.156 10 false VL 2.458,4.219 2.688,4.375 0.229,0.156 10 false HR

Check the switch functions.

i.

Turn the mirror select switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*1 Mirror Select Switch
*2 Mirror Surface Adjust Switch
*3 Mirror Retract Switch
*a Component without harness connected
(Outer Mirror Switch Assembly)

Standard Resistance (for left side):
Tester Connection Switch Condition Specified Condition
1 (B) - 14 (ML+)
10 (VL) - 7 (E)
UP Below 1 Ω
1 (B) - 10 (VL)
14 (ML+) - 7 (E)
DOWN Below 1 Ω
1 (B) - 8 (HL)
14 (ML+) - 7 (E)
LEFT Below 1 Ω
1 (B) - 14 (ML+)
8 (HL) - 7 (E)
RIGHT Below 1 Ω



iii.

Turn the mirror select switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):
Tester Connection Switch Condition Specified Condition
1 (B) - 12 (MR+)
11 (VR)- 7 (E)
UP Below 1 Ω
1 (B) - 11 (VR)
12 (MR+) - 7 (E)
DOWN Below 1 Ω
1 (B) - 9 (HR)
12 (MR+) - 7 (E)
LEFT Below 1 Ω
1 (B) - 12 (MR+)
9 (HR) - 7 (E)
RIGHT Below 1 Ω


If the result is not as specified, replace the outer mirror switch assembly.



b.

Check the mirror retract switch. (w/ Mirror Retract Switch)

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (B) - 6 (MFR)
3 (MRR) - 7 (E)
Mirror retract switch retract position Below 1 Ω
1 (B) - 3 (MRR)
6 (MFR) - 7 (E)
Mirror retract switch return position


If the result is not as specified, replace the outer mirror switch assembly.