Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR
RM2090E _59 Vehicle Exterior _060710 WIPER / WASHER _0297785 FRONT WIPER MOTOR A

WIPER / WASHER  FRONT WIPER MOTOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LHD and RHD vehicles.

·

The procedure listed below is for the LHD vehicles.



PROCEDURE

Hide 85110 1.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

a.

Using a T30 "TORX" socket wrench, install the windshield wiper motor assembly with the 2 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 85012A 2.INSTALL FRONT WIPER CRANK SUB-ASSEMBLY

a.

Connect the windshield wiper motor assembly connector.


b.

Turn the ignition switch to ON.


c.

Operate the wiper and stop the windshield wiper motor assembly at the automatic stop position.


d.

Turn the ignition switch off.


e.

Disconnect the windshield wiper motor assembly connector.


f.

Temporarily install the front wiper crank sub-assembly on the windshield wiper motor assembly with the nut.


g.

Temporarily install the No. 1 rod on the crank arm pivot of the front wiper crank sub-assembly.


h.
B314868E01
0.886,1.692 0.598,2.781 false 2.939,1.671 2.65,2.76 false 2.939,1.671 2.65,2.76 false 1.994,0.391 1.705,1.48 false 2.556,2.819 2.733,2.971 0.177,0.152 10 *1 1.886,0.161 2.063,0.313 0.177,0.152 10 *2 0.475,2.822 0.652,2.974 0.177,0.152 10 *3

Align the nut and crank arm pivot of the front wiper crank sub-assembly with the No. 1 rod, as shown in the illustration.

Text in Illustration
*1 No. 1 Rod
*2 Crank Arm Pivot
*3 Nut


i.

Tighten the front wiper crank sub-assembly with the nut.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


j.
B314869

Apply multemp SA grease to the crank arm pivot of the front wiper crank sub-assembly.


k.
B314870

Connect the No. 1 rod to the crank arm pivot of the front wiper crank sub-assembly.


Hide 85010 3.INSTALL FRONT WIPER MOTOR AND LINK ASSEMBLY

a.
B314864E01
1.791,0.375 1.940,0.520 0.149,0.145 10 *1 2.19,0.611 1.97,0.49 false

Engage the grommet, as shown in the illustration.

Text in Illustration
*1 Grommet

NOTICE:

Be careful not to damage the windshield when installing the front wiper motor and link assembly.



b.

Install the front wiper motor and link assembly with the 2 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


c.

Connect the connector.


Hide 55434E 4.INSTALL CAP

a.

Engage the claw and install the cap.

HINT:

Use the same procedure for the RH side and LH side.



Hide 55781 5.INSTALL COWL VENTILATOR LOUVER

a.

Engage the 15 guides to install the cowl ventilator louver, as shown in the illustration.


b.

Install the 4 cowl top ventilator louver clips.

B314872E01
2.172,5.39 2.332,5.546 0.160,0.156 10 *1 1.221,3.95 2.273,5.333 2.273,5.333 4.142,4.81 false

Text in Illustration
*1 Cowl Top Ventilator Louver Clips - -


c.

Install the 3 clips.


Hide 53866J 6.INSTALL FRONT FENDER TO COWL SIDE SEAL RH

a.

Engage the 4claws to install the clip and front fender to cowl side seal RH.


Hide 53867H 7.INSTALL FRONT FENDER TO COWL SIDE SEAL LH

HINT:

Use the same procedure as for the RH side.


Hide 8.INSTALL WINDSHIELD WIPER ARM AND BLADE ASSEMBLY LH

a.

Operate the wiper and stop the windshield wiper motor at the automatic stop position.


b.
E112237E05
0.307,0.717 0.483,0.899 0.176,0.182 10 *1 0.43,2.768 0.617,2.922 0.187,0.154 10 *2 2.606,3.798 2.785,3.952 0.180,0.154 10 *3 0.493,0.816 1.325,1.438 false 0.641,2.859 1.13,3.285 false 2.582,3.877 1.92,3.489 false

When reusing the windshield wiper arm and blade assembly LH:

i.

Clean the wiper arm serrations.

Text in Illustration
*1 Wiper Arm Serration
*2 Wire Brush
*3 Wiper Pivot Serration



c.

When reusing the windshield wiper link assembly:

i.

Clean the wiper pivot serrations with a wire brush.



d.
B314874E01
1.087,2.303 1.237,2.448 0.150,0.145 10 *1 1.673,2.561 1.28,2.394 false

Install the windshield wiper arm and blade assembly LH with the nut to the position shown in the illustration.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)

Text in Illustration
*1 Ceramic Dot

HINT:

Hold the wiper arm by hand while tightening the nut.



e.

Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.


Hide 9.INSTALL WINDSHIELD WIPER ARM AND BLADE ASSEMBLY RH

a.

Operate the wiper and stop the windshield wiper motor at the automatic stop position.


b.
E112237E06
0.307,0.717 0.483,0.899 0.176,0.182 10 *1 0.43,2.768 0.617,2.922 0.187,0.154 10 *2 2.606,3.798 2.785,3.952 0.180,0.154 10 *3 0.493,0.816 1.325,1.438 false 0.641,2.859 1.13,3.285 false 2.582,3.877 1.92,3.489 false

When reusing the windshield wiper arm and blade assembly RH:

i.

Clean the wiper arm serrations.

Text in Illustration
*1 Wiper Arm Serration
*2 Wire Brush
*3 Wiper Pivot Serration



c.

When reusing the windshield wiper link assembly:

i.

Clean the wiper pivot serrations with a wire brush.



d.
B314873E01
1.569,2.429 1.720,2.573 0.151,0.144 10 *1 1.627,2.599 1.482,2.789 false

Install the windshield wiper arm and blade assembly RH with the nut to the position shown in the illustration.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)

Text in Illustration
*1 Ceramic Dot

HINT:

Hold the wiper arm by hand while tightening the nut.



Hide 85192 10.INSTALL WINDSHIELD WIPER ARM COVER

a.
B314875

Engage the claw to install the windshield wiper arm cover.

HINT:

Use the same procedure for both the RH and LH sides.