Home › Vehicle Exterior › LIGHTING (EXT) › FOG LIGHT ASSEMBLY › from 2016.06
RM2090E _59 Vehicle Exterior _060711 LIGHTING (EXT) _0297798 FOG LIGHT ASSEMBLY N

LIGHTING (EXT)  FOG LIGHT ASSEMBLY  ADJUSTMENT  


CAUTION / NOTICE / HINT

PROCEDURE

Hide 1. PREPARE VEHICLE FOR FOG LIGHT AIM ADJUSTMENT

a.

Prepare the vehicle:

·

Ensure that there is no damage or deformation to the body around the fog lights.

·

Fill the fuel tank.

·

Make sure that the oil is filled to the specified level.

·

Make sure that the coolant is filled to the specified level.

·

Inflate the tires to the appropriate pressure.

·

Unload the trunk and vehicle, ensuring that the spare tire, tools and jack are in their original positions.

·

Sit a person of average weight (75 kg, 165 lb) in the driver's seat.



Hide 2. PREPARE FOR FOG LIGHT AIMING

a.
E252352E01
1.183,1.802 1.359,1.997 0.175,0.195 10 *a 1.077,1.019 1.253,1.214 0.175,0.195 10 *b

Prepare the vehicle (except China):

Text in Illustration
*a 25 or 3 m (82 or 9.84 ft.)
*b 90°

·

Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the fog lights can be observed and above which it cannot.

·

Place the vehicle at a 90° angle to the wall.

·

Create a 25 m (82 ft.) distance between the vehicle (fog light center) and the wall.

·

Make sure that the vehicle is on a level surface.

·

Position the front wheels straight ahead.

·

Bounce the vehicle up and down to settle the suspension.

NOTICE:

A distance of 25 m (82 ft.) between the vehicle (fog light center) and the wall is necessary for proper aim adjustment. If sufficient space is not available, secure a distance of exactly 3 m (9.84 ft.) to allow for checking and adjustment of fog light aim. (The size of the target zone will change with the distance, so follow the instructions in the illustration.)




b.
E252352E01
1.183,1.802 1.359,1.997 0.175,0.195 10 *a 1.077,1.019 1.253,1.214 0.175,0.195 10 *b

Prepare the vehicle (for China):

Text in Illustration
*a 10 or 3 m (32.8 or 9.84 ft.)
*b 90°

·

Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the fog lights can be observed and above which it cannot.

·

Place the vehicle at a 90° angle to the wall.

·

Create a 10 m (32.8 ft.) distance between the vehicle (fog light center) and the wall.

·

Make sure that the vehicle is on a level surface.

·

Position the front wheels straight ahead.

·

Bounce the vehicle up and down to settle the suspension.

NOTICE:

A distance of 10 m (32.8 ft.) between the vehicle (fog light center) and the wall is necessary for proper aim adjustment. If sufficient space is not available, secure a distance of exactly 3 m (9.84 ft.) to allow for checking and adjustment of fog light aim. (The size of the target zone will change with the distance, so follow the instructions in the illustration.)




c.

Prepare a piece of thick white paper (approximately 2 m (6.56 ft.) (height) x 4 m (13.1 ft.) (width)) to use as a screen.


d.

Draw a vertical line down the center of the screen (V line).


e.

Set the screen as shown in the illustration (except China).

E252351E02
0.74,0.188 0.958,0.396 0.219,0.208 12 false *A 4.323,0.188 4.542,0.396 0.219,0.208 12 false *B 1.656,1.031 1.958,1.25 0.302,0.219 10 false *a 1.302,1.25 1.604,1.469 0.302,0.219 10 false *e 4.844,1.25 5.146,1.469 0.302,0.219 10 false *e 1.146,3.49 1.448,3.708 0.302,0.219 10 false *e 4.698,3.49 5,3.708 0.302,0.219 10 false *e 1.646,1.896 1.948,2.115 0.302,0.219 10 false *b 2.979,1.479 3.281,1.698 0.302,0.219 10 false *d 6.083,1.458 6.385,1.677 0.302,0.219 10 false *d 4.979,1.865 5.281,2.083 0.302,0.219 10 false *b 1.656,4.135 1.958,4.354 0.302,0.219 10 false *f 4.99,4.125 5.292,4.344 0.302,0.219 10 false *g 4.958,1.042 5.26,1.26 0.302,0.219 10 false *a 0.635,3.667 0.781,3.865 0.146,0.198 10 false *c 4.188,3.688 4.333,3.885 0.146,0.198 10 false *c

Text in Illustration
*1 Aligning distance 25 m (82 ft.) *2 Aligning distance 3 m (9.84 ft.)
*a V RH Line *b V LH Line
*c H Line *d V Line
*e 90° *f 25 m (82 ft.)
*g 3 m (9.84 ft.) - -

HINT:
·

Stand the screen perpendicular to the ground.

·

Align the V line on the screen with the center of the vehicle.




f.

Set the screen as shown in the illustration (for China).

E252351E02
0.74,0.188 0.958,0.396 0.219,0.208 12 false *A 4.323,0.188 4.542,0.396 0.219,0.208 12 false *B 1.656,1.031 1.958,1.25 0.302,0.219 10 false *a 1.302,1.25 1.604,1.469 0.302,0.219 10 false *e 4.844,1.25 5.146,1.469 0.302,0.219 10 false *e 1.146,3.49 1.448,3.708 0.302,0.219 10 false *e 4.698,3.49 5,3.708 0.302,0.219 10 false *e 1.646,1.896 1.948,2.115 0.302,0.219 10 false *b 2.979,1.479 3.281,1.698 0.302,0.219 10 false *d 6.083,1.458 6.385,1.677 0.302,0.219 10 false *d 4.979,1.865 5.281,2.083 0.302,0.219 10 false *b 1.656,4.135 1.958,4.354 0.302,0.219 10 false *f 4.99,4.125 5.292,4.344 0.302,0.219 10 false *g 4.958,1.042 5.26,1.26 0.302,0.219 10 false *a 0.635,3.667 0.781,3.865 0.146,0.198 10 false *c 4.188,3.688 4.333,3.885 0.146,0.198 10 false *c

Text in Illustration
*1 Aligning distance 10 m (32.8 ft.) *2 Aligning distance 3 m (9.84 ft.)
*a V RH Line *b V LH Line
*c H Line *d V Line
*e 90° *f 10 m (32.8 ft.)
*g 3 m (9.84 ft.) - -

HINT:
·

Stand the screen perpendicular to the ground.

·

Align the V line on the screen with the center of the vehicle.




g.
I033423E77
0.979,0.344 1.167,0.5 0.188,0.156 10 false *a 1.615,0.344 1.792,0.5 0.177,0.156 10 false *b 0.365,1.708 0.542,1.865 0.177,0.156 10 false *e 2.74,0.885 2.927,1.052 0.188,0.167 10 false *d 2.25,0.333 2.438,0.49 0.188,0.156 10 false *c

Draw base lines (H, V LH, and V RH lines) on the screen as shown in the illustration.

HINT:

Mark the fog light center marks on the screen. If the center mark cannot be observed on the fog light, use the center of the fog light or the manufacturer's name marked on the fog light as the center mark.


i.

H Line (Fog light height):

Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the fog light center marks of the fog lights.


ii.

V LH Line, V RH Line (Center mark position of left-hand (LH) and right-hand (RH) fog lights):

Draw 2 vertical lines so that they intersect the H line at each center mark (aligned with the center of the fog light).

Text in Illustration
*a V LH Line
*b V Line
*c V RH Line
*d H Line
*e Ground



Hide 3.INSPECT FOG LIGHT AIMING

a.

Cover the fog light or disconnect the connector of the fog light on the opposite side to prevent light from the fog light that is not being inspected from affecting the fog light aiming inspection.

NOTICE:

Do not keep the fog light covered for more than 3 minutes. The fog light lens is made of synthetic resin, which may melt or be damaged due to excessive heat.



b.

Start the engine.


c.

Turn on the fog lights and check if the upper edge of the hot zone for each fog light matches the upper edge as shown in the illustration (except China).

E361969E01
2.333,2.292 2.146,2.292 2.146,2.292 1.938,1.885 true 5.708,2.292 5.521,2.292 5.521,2.292 5.313,1.885 true 0.479,0.208 0.854,0.448 0.375,0.24 12 false *A 4.01,0.167 4.385,0.406 0.375,0.24 12 false *B 1.74,0.865 2.115,1.104 0.375,0.24 10 false *a 1.74,1.177 2.115,1.417 0.375,0.24 10 false *b 5.063,1.219 5.438,1.458 0.375,0.24 10 false *b 5.052,0.885 5.427,1.125 0.375,0.24 10 false *a 0.51,1.469 0.885,1.708 0.375,0.24 10 false *c 3.844,1.469 4.219,1.708 0.375,0.24 10 false *c 3.01,1.719 3.635,1.927 0.625,0.208 10 false 375 mm 6.375,1.719 7,1.927 0.625,0.208 10 false 45 mm 2.385,2.208 2.76,2.448 0.375,0.24 10 false *d 5.75,2.198 6.125,2.438 0.375,0.24 10 false *d

Text in Illustration
*A Aligning distance 25 m (82 ft.) *B Aligning distance 3 m (9.84 ft.)
*a V RH Line *b V LH Line
*c H Line *d Hot Zone

HINT:
·

If the alignment distance is 25 m (82 ft.):

The upper edge of the hot zone for the fog light should be 375 mm (1.23 ft.) below the H line.

·

If the alignment distance is 3 m (9.84 ft.):

The upper edge of the hot zone for the fog light should be 45 mm (1.77 in.) below the H line.




d.

Turn on the fog lights and check if the upper edge of the hot zone for each fog light matches the upper edge as shown in the illustration (for China).

E361969E02
2.302,2.344 2.104,2.344 2.104,2.344 1.948,1.875 true 5.656,2.365 5.458,2.365 5.458,2.365 5.302,1.896 true 0.406,0.208 0.719,0.406 0.313,0.198 12 false *A 4.042,0.198 4.354,0.396 0.313,0.198 12 false *B 1.729,0.823 2.042,1.021 0.313,0.198 10 false *a 5.073,0.823 5.385,1.021 0.313,0.198 10 false *a 1.729,1.167 2.042,1.365 0.313,0.198 10 false *b 5.083,1.156 5.396,1.354 0.313,0.198 10 false *b 0.531,1.469 0.844,1.667 0.313,0.198 10 false *c 3.865,1.469 4.177,1.667 0.313,0.198 10 false *c 2.344,2.271 2.656,2.469 0.313,0.198 10 false *d 5.688,2.271 6,2.469 0.313,0.198 10 false *d 6.365,1.729 6.823,1.896 0.458,0.167 10 false 45 mm 2.979,1.719 3.604,1.948 0.625,0.229 10 false 150 mm

Text in Illustration
*A Aligning distance 10 m (32.8 ft.) *B Aligning distance 3 m (9.84 ft.)
*a V RH Line *b V LH Line
*c H Line *d Hot Zone

HINT:
·

If the alignment distance is 10 m (32.8 ft.):

The upper edge of the hot zone for the fog light should be 150 mm (5.90 in.) below the H line.

·

If the alignment distance is 3 m (9.84 ft.):

The upper edge of the hot zone for the fog light should be 45 mm (1.77 in.) below the H line.




Hide 4.ADJUST FOG LIGHT AIMING

a.
E356549E02
1.229,3.063 1.542,3.063 true 1.063,2.979 1.25,3.177 0.188,0.198 10 false *1

Adjust the aim vertically:

Adjust the aim of each fog light to the specified range by turning each aiming screw with a screwdriver.

Text in Illustration
*1 Aiming Screw

NOTICE:

The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.


HINT:

If it is not possible to correctly adjust fog light aim, check fog light installation.