Home › Vehicle Exterior › LIGHTING (EXT) › TURN SIGNAL FLASHER ASSEMBLY
RM2090E _59 Vehicle Exterior _060711 LIGHTING (EXT) _0297814 TURN SIGNAL FLASHER ASSEMBLY G

LIGHTING (EXT)  TURN SIGNAL FLASHER ASSEMBLY  INSPECTION  


PROCEDURE

Hide 81980 1.INSPECT TURN SIGNAL FLASHER ASSEMBLY

a.
U146862E03
0.854,1.781 1.167,1.365 true 0.844,0.563 1.177,0.958 true 2.125,1.802 1.958,1.365 true 0.094,0.031 0.281,0.188 0.188,0.156 10 false *a 1.542,0.24 1.833,0.396 0.292,0.156 10 false D61 2.042,1.844 2.385,2.021 0.344,0.177 10 false GND 0.708,1.823 0.917,2 0.208,0.177 10 false +B 0.688,0.417 0.896,0.594 0.208,0.177 10 false IG

Disconnect the D61 turn signal flasher assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D61-4 (+B) - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
D61-1 (IG) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Turn Signal Flasher Assembly)

If the result is not as specified, repair or replace the wire harness or connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
D61-7 (GND) - Body ground Always Below 1 Ω


If the result is not as specified, repair or replace the wire harness or connector.


d.
U147237E02
0.677,2.74 1.156,2.229 true 1.365,2.76 1.677,2.24 true 2.313,2.74 2.031,2.24 true 0.813,1.177 1.125,1.729 true 2.042,1.729 2.417,1.177 true 0.167,0.115 0.354,0.271 0.188,0.156 10 false *a 1.531,0.698 1.823,0.854 0.292,0.156 10 false D61 0.667,0.958 0.896,1.135 0.229,0.177 10 false LL 2.375,0.948 2.604,1.125 0.229,0.177 10 false LR 2.292,2.781 2.583,2.958 0.292,0.177 10 false EL 1.25,2.792 1.542,2.969 0.292,0.177 10 false ER 0.479,2.771 0.844,2.948 0.365,0.177 10 false EHW

Reconnect the D61 turn signal flasher assembly connector.


e.

Measure the voltage according to the valve(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D61-6 (ER) - Body ground Turn signal switch in RH position OFF to ON 9 V or higher to below 1 V
D61-5 (EL) - Body ground Turn signal switch in LH position OFF to ON 9 V or higher to below 1 V
D61-8 (EHW) - Body ground Hazard warning switch OFF to ON 9 V or higher to below 1 V
D61-2 (LR) - Body ground Turn signal switch in RH position OFF to ON Below 1 V to 9 V (60 to 120 times per minute)
D61-3 (LL) - Body ground Turn signal switch in LH position OFF to ON Below 1 V to 9 V (60 to 120 times per minute)
D61-2 (LR) - Body ground Hazard warning switch OFF to ON Below 1 V to 9 V (60 to 120 times per minute)
D61-3 (LL) - Body ground Hazard warning switch OFF to ON Below 1 V to 9 V (60 to 120 times per minute)


Text in Illustration
*a Component with harness connected
(Turn Signal Flasher Assembly)

If the result is not as specified, the turn signal flasher assembly may have a malfunction.