Home › Vehicle Exterior › LIGHTING (EXT) › RELAY › 2012.03–2016.06
RM2090E _59 Vehicle Exterior _060711 LIGHTING (EXT) _0297815 RELAY G

LIGHTING (EXT)  RELAY  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT H-LP RELAY

a.
A188757E17
1.76,0.708 2.104,0.708 true 2.76,0.719 3.083,0.719 true 2.656,1.115 3.083,1.115 true 2.656,1.594 3.083,1.594 true 0.323,0.76 0.438,0.917 0.115,0.156 10 false 5 0.323,1.281 0.438,1.438 0.115,0.156 10 false 1 1.646,0.615 1.76,0.771 0.115,0.156 10 false 1 1.302,0.76 1.417,0.917 0.115,0.156 10 false 3 1.302,1.281 1.417,1.438 0.115,0.156 10 false 2 3.125,0.615 3.24,0.771 0.115,0.156 10 false 2 3.125,0.99 3.24,1.146 0.115,0.156 10 false 5 3.125,1.49 3.24,1.646 0.115,0.156 10 false 3 0.219,0.156 0.479,0.375 0.26,0.219 10 false *a

Remove the H-LP relay from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Voltage is not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Voltage is applied between terminals 1 and 2 Below 1 Ω


Text in Illustration
*a Component without harness connected
(H-LP Relay)

If the result is not as specified, replace the H-LP relay.


Hide 2.INSPECT DIM RELAY

a.
A188757E17
1.76,0.708 2.104,0.708 true 2.76,0.719 3.083,0.719 true 2.656,1.115 3.083,1.115 true 2.656,1.594 3.083,1.594 true 0.323,0.76 0.438,0.917 0.115,0.156 10 false 5 0.323,1.281 0.438,1.438 0.115,0.156 10 false 1 1.646,0.615 1.76,0.771 0.115,0.156 10 false 1 1.302,0.76 1.417,0.917 0.115,0.156 10 false 3 1.302,1.281 1.417,1.438 0.115,0.156 10 false 2 3.125,0.615 3.24,0.771 0.115,0.156 10 false 2 3.125,0.99 3.24,1.146 0.115,0.156 10 false 5 3.125,1.49 3.24,1.646 0.115,0.156 10 false 3 0.219,0.156 0.479,0.375 0.26,0.219 10 false *a

Remove the DIM relay from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Voltage is not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Voltage is applied between terminals 1 and 2 Below 1 Ω


Text in Illustration
*a Component without harness connected
(DIM Relay)

If the result is not as specified, replace the DIM relay.


Hide 3.INSPECT RR FOG RELAY

a.
A188757E17
1.76,0.708 2.104,0.708 true 2.76,0.719 3.083,0.719 true 2.656,1.115 3.083,1.115 true 2.656,1.594 3.083,1.594 true 0.323,0.76 0.438,0.917 0.115,0.156 10 false 5 0.323,1.281 0.438,1.438 0.115,0.156 10 false 1 1.646,0.615 1.76,0.771 0.115,0.156 10 false 1 1.302,0.76 1.417,0.917 0.115,0.156 10 false 3 1.302,1.281 1.417,1.438 0.115,0.156 10 false 2 3.125,0.615 3.24,0.771 0.115,0.156 10 false 2 3.125,0.99 3.24,1.146 0.115,0.156 10 false 5 3.125,1.49 3.24,1.646 0.115,0.156 10 false 3 0.219,0.156 0.479,0.375 0.26,0.219 10 false *a

Remove the RR FOG relay from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Voltage is not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Voltage is applied between terminals 1 and 2 Below 1 Ω


Text in Illustration
*a Component without harness connected
(RR FOG Relay)

If the result is not as specified, replace the RR FOG relay.


Hide 4.INSPECT DRL RELAY

a.
E223161E01
0.072,0 0.320,0.248 0.248,0.248 10 *a

Remove the DRL relay from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 4 Battery voltage not applied Below 1 Ω
3 - 4 Battery voltage applied to terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage not applied 10 kΩ or higher
3 - 5 Battery voltage applied to terminals 1 and 2 Below 1 Ω


Text in Illustration
*a Component without harness connected
(DRL Relay)

If the result is not as specified, replace the DRL relay.