Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › ROOF DRIP SIDE FINISH MOULDING
RM2090E _59 Vehicle Exterior _060713 EXTERIOR PANELS / TRIM _0297826 ROOF DRIP SIDE FINISH MOULDING A

EXTERIOR PANELS / TRIM  ROOF DRIP SIDE FINISH MOULDING  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for both the RH and LH sides.

·

The following procedure is for the LH side.



PROCEDURE

Hide 75561 1.INSTALL NO. 1 ROOF DRIP SIDE FINISH MOULDING CLIP

NOTICE:
·

If reusing the clips, do not remove the double-sided tape remaining on the clips and where the clips will be installed on the body.

·

If installing new clips, remove the double-sided tape remaining where the clips will be installed on the body and clean the body with a non-residue solvent.



a.
B229383E02
2.976,0.677 3.148,0.846 0.172,0.169 10 *1 2.55,0.761 2.965,0.761 false 1.429,0.081 1.612,0.346 0.183,0.265 10 *a 2.224,0.944 1.903,0.167 1.903,0.167 1.641,0.167 false

Apply a 2 to 3 mm (0.0787 to 0.118 in.) bead of adhesive (3M DP-105 or equivalent) to new No. 1 roof drip side finish moulding clip.

Text in Illustration
*1 Adhesive
*a 2 to 3 mm (0.0787 to 0.118 in.) Bead of Adhesive

HINT:

Adhesive strength (tensile strength): 13.7 MPa (140 kgf/cm2, 1987 psi) or more (when the temperature is 23°C (73°F)).



b.

Press and install the No. 1 roof drip side finish moulding clip.


c.

Install the clips to the positions on the roof panel shown in the illustration. Determine the locations and firmly press and install the No. 1 roof drip side finish moulding clip after lightly applying adhesive (3M DP-105 or equivalent).

B313069E03
1.302,3 0.906,3.667 false 2.646,3.26 3.104,3.656 false 5.896,2.927 6.292,3.594 false 4.552,3.188 4.104,3.583 false 0.781,3.719 0.927,3.865 0.146,0.146 10 false *1 3.125,3.656 3.271,3.802 0.146,0.146 10 false *2 2.052,4.188 2.177,4.333 0.125,0.146 10 false a 6.323,3.635 6.469,3.781 0.146,0.146 10 false *1 3.927,3.594 4.073,3.74 0.146,0.146 10 false *2 5.042,4.125 5.167,4.271 0.125,0.146 10 false a 5.521,0.448 5.646,0.594 0.125,0.146 10 true b 1.667,0.479 1.792,0.625 0.125,0.146 10 false c 2.031,0.698 2.156,0.844 0.125,0.146 10 false A 2.135,1.76 2.26,1.906 0.125,0.146 10 false A 5.219,0.667 5.344,0.813 0.125,0.146 10 false B 5.281,1.625 5.406,1.771 0.125,0.146 10 false B 4.125,2.375 4.396,2.521 0.271,0.146 10 false B-B 1.396,2.521 1.667,2.667 0.271,0.146 10 false A-A

Standard Dimension:
Area Dimension
a 2.0 mm (0.0787 in.)
b 26.2 mm (1.0315 in.)
c 20.5 mm (0.8071 in.)


Text in Illustration
*1 Out Side Panel *2 Roof Panel


d.

Install the roof drip center side finish moulding when 40 minutes or more have elapsed after pressing and installing the No. 1 roof drip side finish moulding clips.

HINT:
·

Initial hardening time: 40 minutes

·

Complete hardening time: 24 hours




Hide 75555D 2.INSTALL CENTER ROOF DRIP SIDE FINISH MOULDING

a.
B313068

Engage the 2 clips and install the center roof drip side finish moulding, as shown in the illustration.