Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER › from 2016.06
RM2090E _59 Vehicle Exterior _060713 EXTERIOR PANELS / TRIM _0297829 FRONT BUMPER A

EXTERIOR PANELS / TRIM  FRONT BUMPER  DISASSEMBLY  


PROCEDURE

Hide 53395E 1.REMOVE HOOD TO FRONT END PANEL SEAL

a.
B322369

Remove the 13 clips and hood to front end panel seal from the front bumper upper retainer.


Hide 2.REMOVE LICENSE PLATE BRACKET

a.

Type A

i.
B405807

Remove the 2 bolts and license plate bracket.



b.

Type B

i.
B405808

Remove the 2 bolts and license plate bracket.



Hide 52116D 3.REMOVE NO. 2 FRONT BUMPER SIDE SUPPORT LH

a.
B312510

Remove the screw.


b.
B312511

Disengage the 2 claws and remove the No. 2 front bumper side support LH.


Hide 52115D 4.REMOVE NO. 2 FRONT BUMPER SIDE SUPPORT RH

HINT:

Use the same procedure as for the LH side.


Hide 52124B 5.REMOVE FRONT BUMPER REINFORCEMENT PLATE LH

a.
B312512

Remove the 2 clips and the front bumper reinforcement plate LH.


Hide 52123B 6.REMOVE FRONT BUMPER REINFORCEMENT PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 52129B 7.REMOVE FRONT LOWER BUMPER COVER

a.
B312513

Remove the 3 bolts.


b.

Remove the 4 clips and the front lower bumper cover.


Hide 53293 8.REMOVE FRONT BUMPER STAY BRACKET

a.
B312514

Remove the 3 bolts and the front bumper stay bracket.


Hide 52611 9.REMOVE FRONT BUMPER ENERGY ABSORBER

a.
B312515

Remove the front bumper energy absorber.


Hide 53291B 10.REMOVE RADIATOR COVER PLATE

a.
B312516

Remove the 6 clips and the radiator cover plate.


Hide 86510 11.REMOVE HIGH PITCHED HORN ASSEMBLY (except China)

Hide 86510 12.REMOVE LOW PITCHED HORN ASSEMBLY (for China)

Hide 52021 13.REMOVE FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY

a.
B312517

Remove the 8 bolts and the front bumper reinforcement sub-assembly.


Hide 75311 14.REMOVE RADIATOR GRILLE (OR FRONT PANEL) EMBLEM

Hide 53112E 15.REMOVE NO. 1 LOWER RADIATOR GRILLE

a.
B457861

Disengage the 26 claws and remove the No. 1 lower radiator grille.


Hide 52128C 16.REMOVE FRONT BUMPER HOLE COVER LH

a.
B457862

Remove the 3 screws and the front bumper hole cover LH.


Hide 52127D 17.REMOVE FRONT BUMPER HOLE COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 81220 18.REMOVE FOG LIGHT ASSEMBLY LH (w/ Fog Light)

Hide 81210A 19.REMOVE FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT:

Use the same procedure as for the LH side.


Hide 81482C 20.REMOVE FOG LIGHT COVER LH

a.
B457863

Disengage the 10 claws and remove the fog light cover LH.


Hide 81481E 21.REMOVE FOG LIGHT COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 52127C 22.REMOVE FRONT BUMPER HOLE COVER

a.
B457864

Disengage the 4 claws and remove the front bumper hole cover (upper side).


b.
B457865

Disengage the 7 claws and remove the front bumper hole cover (lower side).


Hide 23.REMOVE FRONT BUMPER SIDE RETAINER LH

a.

Put a 4 mm (0.1575 in.) drill bit into a drill.


b.
B329647E01
2.924,0.855 3.107,1.025 0.182,0.171 10 *a 0.927,1.486 1.109,1.657 0.182,0.171 10 *1 1.136,1.549 1.786,1.242 false

Wind tape around the drill bit approximately 5 mm (0.1969 in.) from the tip of the drill, as shown in the illustration.

HINT:

Tape the 4 mm (0.1575 in.) drill bit to prevent the drill bit from going too deep.


Text in Illustration
*1 Drill
*a Matchmark


c.

Lightly press the drill against the 2 rivets and drill off the flanges of the 2 rivets.

NOTICE:

Take care with the drilled rivet as it may become hot.


HINT:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivet with the drill because this may cause damage to the installation holes of the rivet or the drill bit.




Hide 24.REMOVE FRONT BUMPER SIDE RETAINER RH

HINT:

Use the same procedure as for the LH side.