Home › Brake › BRAKE (FRONT) › FRONT BRAKE(for Opposed Type Caliper) › from 2017.03
RM2090E _54 Brake _060686 BRAKE (FRONT) _0313978 FRONT BRAKE(for Opposed Type Caliper) A

BRAKE (FRONT)  FRONT BRAKE(for Opposed Type Caliper)  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 2.DRAIN BRAKE FLUID

NOTICE:

Immediately wash off any brake fluid that comes into contact with any painted surfaces.


Hide 3.REMOVE FRONT DISC BRAKE PAD

a.
C376552C02
1.125,1.438 0.521,1.885 0.521,1.885 1.281,0.792 true 1.552,0.833 2.094,2.01 2.094,2.01 1.479,1.479 true 0.906,1.906 1.479,1.313 true 1.417,0.781 2.26,0.25 2.26,0.25 1.74,0.813 true 0.354,1.854 0.667,2.01 0.313,0.156 10 false *a 2.167,1.979 2.479,2.135 0.313,0.156 10 false *b 0.76,1.927 1.073,2.083 0.313,0.156 10 false *c 2.323,0.156 2.635,0.313 0.313,0.156 10 false *d
*a Pin Hold Clip
*b Front Disc Brake Cylinder Slide Pin
*c No. 1 Front Disc Brake Pad Support Plate
*d Front Disc Brake Pad


Remove the 2 pin hold clips.


b.

Using a 3 mm pin punch and a hammer, remove the 2 front disc brake cylinder slide pins and No. 1 front disc brake pad support plate.


c.

Remove the 2 front disc brake pads from the front disc brake cylinder assembly.


d.
C376463C02
1.146,0.51 1.833,0.51 false 1.667,0.333 2.354,0.333 false 2.333,0.135 3.021,0.135 false 1.646,1.615 2.333,1.615 false 1.073,1.854 1.76,1.854 false 0.385,2.083 1.073,2.083 false 0.948,0.438 1.26,0.594 0.313,0.156 10 false *a 1.469,0.24 1.781,0.396 0.313,0.156 10 false *b 2.156,0.031 2.469,0.188 0.313,0.156 10 false *c 2.365,1.51 2.677,1.667 0.313,0.156 10 false *a 1.802,1.76 2.115,1.917 0.313,0.156 10 false *b 1.135,1.979 1.448,2.135 0.313,0.156 10 false *c
*a Front Disc Brake Pad
*b No. 1 Anti-squeal Sim
*c No. 2 Anti-squeal Sim


Remove the 2 No. 1 anti-squeal sim and the 2 No. 2 anti-squeal sim from each pad.


Hide 4.DISCONNECT FRONT NO. 1 FLEXIBLE HOSE

a.
C376462

Remove the union bolt, 2 gaskets and disconnect the front No. 1 flexible hose from the front disc brake cylinder assembly.


Hide 5.REMOVE FRONT DISC BRAKE CYLINDER ASSEMBLY

a.
C364375

Remove the 2 bolts, front disc brake cylinder mounting and front disc brake cylinder assembly.


Hide 43512 6.REMOVE FRONT DISC

a.
C184280C06
1.698,1.292 2.542,0.354 2.542,0.354 1.74,1.365 true 2.594,0.26 2.906,0.417 0.313,0.156 10 false *a
*a Matchmark


Place matchmarks on the front disc and front axle hub.

HINT:

It is not necessary when replacing the disc.



b.

Remove the front disc.