Home › Brake › PARKING BRAKE › PARKING BRAKE ASSEMBLY › from 2017.03
RM2090E _54 Brake _060688 PARKING BRAKE _0297640 PARKING BRAKE ASSEMBLY A

PARKING BRAKE  PARKING BRAKE ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

The procedure listed below is for the LH side.

·

Use the same procedure for the RH and LH sides.



PROCEDURE

Hide 1.APPLY DISC BRAKE GREASE

a.
C218935

Apply a light coat of disc brake grease to the areas of the backing plate which make contact with the shoe as shown in the illustration.

Text in Illustration
V100144

Disc Brake Grease


Hide 46550B 2.INSTALL PARKING BRAKE SHOE PIN

a.

Install the parking brake shoe pin.


Hide 47612 3.INSTALL PARKING BRAKE SHOE LEVER LH

a.

Apply a light coat of disc brake grease to the areas of the parking brake shoe lever LH which make contact with the parking brake shoe pin.


b.

Install the parking brake shoe lever LH to the parking brake shoe.


Hide 46550D 4.INSTALL PARKING BRAKE SHOE WAVE WASHER

a.

Install the parking brake shoe wave washer.


Hide 46550C 5.INSTALL PARKING BRAKE SHOE TYPE C WASHER

a.

Install a new parking brake shoe type C washer.


b.
C064144

Using a pair of pliers, squeeze together the ends of the parking brake shoe type C washer.


Hide 46430 6.INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY

a.

Using needle-nose pliers, connect the No. 3 parking brake cable assembly to the parking brake shoe lever LH.


Hide 46550G 7.INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING

a.
C236249

Install the parking brake shoe return tension spring to the parking brake shoe.


Hide 04495A 8.INSTALL PARKING BRAKE SHOE KIT

a.
C236248

Install the parking brake shoe to the parking brake shoe return tension spring.


Hide 47406A 9.INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET

a.
C263281

Apply disc brake grease to the parking brake shoe adjusting screw set as shown in the illustration.


b.

Install the parking brake shoe adjusting screw set to the parking brake shoes.

NOTICE:

Take care to install the correct parking brake shoe adjusting screw set because the direction of the parking brake shoe adjusting screw set is different between the left and right sides.


Text in Illustration
V100144

Disc Brake Grease
V100135

For front side (LH Side)
For rear side (RH Side)


c.
C263270

Expand the parking brake shoes outward by hand and fit them to the parking brake plate.


Hide 47447C 10.INSTALL PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for Rear Side)

a.

Install the parking brake shoe hold down spring pin (for rear side) to the parking brake plate.


Hide 47447D 11.INSTALL PARKING BRAKE SHOE HOLD DOWN COMPRESSION SPRING (for Rear Side)

a.
C260015E01
1.924,1.871 1.576,1.871 1.576,1.871 1.33,1.611 false 1.955,1.777 2.243,1.937 0.288,0.159 10 SST

Using SST, install the parking brake shoe hold down compression spring (for rear side) as shown in the illustration.

SST
09718-00011  


Hide 47614 12.INSTALL PARKING BRAKE SHOE STRUT LH

a.

Pull the parking brake shoe towards the front of the vehicle by hand as shown in the illustration.


b.

Install the parking brake shoe strut LH.


c.
C263282E02
1.958,0.896 2.26,0.583 2.26,0.583 2.51,0.583 true 2.542,0.521 2.708,0.677 0.167,0.156 10 false *1

Install the parking brake shoe.

Text in Illustration
*1 Parking Brake Shoe Strut LH


Hide 47447C 13.INSTALL PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for Front Side)

a.

Install the parking brake shoe hold down spring pin (for Front side) to the parking brake plate.


Hide 47447D 14.INSTALL PARKING BRAKE SHOE HOLD DOWN COMPRESSION SPRING (for Front Side)

a.
C260013E02
1.948,1.479 2.292,1.479 false 2.323,1.406 2.615,1.563 0.292,0.156 10 false SST

Using SST, install the parking brake shoe hold down compression spring (for Front Side) as shown in the illustration.

SST
09718-00011  


Hide 47613D 15.INSTALL PARKING BRAKE SHOE STRUT COMPRESSION SPRING

a.

Install the parking brake shoe strut compression spring to the shoe strut.


Hide 46550E 16.INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Rear Side)

a.

Install the parking brake shoe return tension spring (for rear side).


Hide 46550E 17.INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Front Side)

a.

Install the parking brake shoe return tension spring (for front side).


Hide 18. CHECK PARKING BRAKE INSTALLATION

a.

Make sure that all the parts are installed properly. If necessary, remove and reinstall the parts.

C260019E02
1.75,0.115 2.01,0.365 0.26,0.25 10 false *a 5.26,0.115 5.521,0.365 0.26,0.25 10 false *b

Text in Illustration
*a LH Side *b RH Side
V100135

Front of the Vehicle - -


Hide 42431 19.INSTALL REAR DISC

a.
C186060E03
1.698,1.313 2.625,0.385 true 1.719,1.438 2.625,0.385 true 2.625,0.229 2.802,0.396 0.177,0.167 10 false *a

Align the matchmarks of the rear disc and rear axle hub, and install the rear disc.

Text in Illustration
*a Matchmark

HINT:

When replacing the disc with a new one, select the installation position where the rear disc has minimal runout.



Hide 20.ADJUST PARKING BRAKE SHOW CLEARANCE AND PARKING BRAKE LEVER TRAVEL

a.

Temporarily install the hub nuts to the hub bolts.


b.

Remove the parking brake shoe adjusting hole plug.


c.

Turn the shoe adjuster and expand the shoes until the disc locks.

C256640E01
5.21,0.333 5.385,0.503 0.174,0.170 10 *a 4.673,0.768 4.848,0.937 0.174,0.170 10 *b

Text in illustration
*a Expand *b Contract


d.

Turn and contract the shoe adjuster until the disc can rotate smoothly.

Standard:

Returns 10 notches.



e.

Check that the parking brake does not drag.


f.

Remove the hub nuts from the hub bolts.


Hide 21.INSTALL REAR DISC BRAKE CALIPER ASSEMBLY LH

a.

for Floating Type Caliper

i.

Install the rear disc brake caliper assembly LH with new 2 bolts.

Torque:
Bolt Type A : 66 N*m (673 kgf*cm, 49 ft.*lbf)
Bolt Type B : 110 N*m (1122 kgf*cm, 81 ft.*lbf)

HINT:
C398291C01
0.177,0.146 0.49,0.344 0.313,0.198 10 false *A 0.177,1.25 0.49,1.448 0.313,0.198 10 false *B 0.75,0.458 1.063,0.656 0.313,0.198 10 false *a 0.74,1.573 1.052,1.771 0.313,0.198 10 false *a

Bolt type A and bolt type B can be distinguished by the sizes of the mounting bolts.

Bolt Type Width Across Flats
A 14 mm (0.551 in.)
B 17 mm (0.669 in.)

Text in Illustration
*A Bolt Type A
*B Bolt Type B
*a Width Across Flats




b.

for Opposed Type Caliper

i.

Install the rear disc brake caliper assembly LH with the 2 bolts.

Torque:
73 N*m (744 kgf*cm, 54 ft.*lbf)



Hide 22.INSPECT PARKING BRAKE LEVER TRAVEL

Hide 23.ADJUST PARKING BRAKE LEVER TRAVEL

Hide 24.INSTALL REAR WHEEL

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)