Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM › from 2019.03
RM2090E _56 Audio / Visual / Telematics _082076 PARK ASSIST / MONITORING _0396236 REAR VIEW MONITOR SYSTEM U

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM  TERMINALS OF ECU  


INNER REAR VIEW MIRROR ASSEMBLY


E389361E02
3.313,0.094 3.729,0.344 0.417,0.25 3.438,0.146 3.938,0.51 0.5,0.365 10 false K6

a.

Disconnect the K6 inner rear view mirror assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K6-1 - Body ground V - Body ground Power source (IG) Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
K6-2 - Body ground B - Body ground Ground Always Below 1 Ω
K6-3 - K6-2 L - B Reverse signal Ignition switch ON, shift lever other than R Below 1 V
Ignition switch ON, shift lever in R 11 to 14 V
K6-6 - K6-2 G - B Power supply to rear television camera assembly Ignition switch ON, shift lever in R 5.5 to 7.05 V
K6-7 - K6-2 R - B Rear television camera assembly ground Always Below 1 V


c.

Reconnect the K6 inner rear view mirror assembly connector.


d.

Measure the resistance and waveform according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K6-8 - K6-2 B - B Video signal Ignition switch ON, shift lever in R, camera lens not covered, displaying an image+ Pulse generation
(See waveform 1)
Ignition switch ON, shift lever in R, camera lens covered, blacking out screen Pulse generation
(See waveform 2)
K6-9 - Body ground Shielded - Body ground Shielded ground Always Below 1 Ω


e.
E265840C03
0.823,2.073 1,2.073 1,2.073 1.125,1.583 false 1.479,2.063 1.344,2.063 1.344,2.063 1.229,1.479 false 0.781,4.167 0.958,4.167 0.958,4.167 1.156,3.594 false 1.521,4.125 1.385,4.125 1.385,4.125 1.271,3.542 false 0.229,0.229 0.542,0.427 0.313,0.198 10 *a 0.396,1.052 0.76,1.313 0.365,0.26 10 GND 0.396,3.208 0.76,3.469 0.365,0.26 10 GND 0.26,2.271 0.625,2.531 0.365,0.26 10 *b 0.646,4.073 1.01,4.333 0.365,0.26 10 *c 0.656,1.979 1.021,2.24 0.365,0.26 10 *c 1.51,1.969 1.875,2.229 0.365,0.26 10 *d 1.542,4.052 1.906,4.313 0.365,0.26 10 *d
*a Waveform 1
*b Waveform 2
*c Synchronization Signal
*d Video Waveform


Reference (Oscilloscope waveform):

i.

Waveform 1

Item Content
Terminal No. (Symbol) K6-8 - K6-2
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Ignition switch ON, shift lever in R, camera lens not covered, displaying an image

HINT:

The video waveform changes according to the image sent by the rear television camera assembly.



ii.

Waveform 2

Item Content
Terminal No. (Symbol) K6-8 - K6-2
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Ignition switch ON, shift lever in R, camera lens covered, blacking out screen

HINT:

The video waveform changes according to the image sent by the rear television camera assembly.





REAR TELEVISION CAMERA ASSEMBLY


E389362E01
3.354,0.156 3.771,0.406 0.417,0.25 3.5,0.208 3.927,0.542 0.427,0.333 10 false J5

a.

Disconnect the J5 rear television camera assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J5-3 (CB+) - Body ground Y - Body ground Power source Ignition switch ON, shift lever in R 5.5 to 7.05 V


c.

Reconnect the J5 rear television camera assembly connector.


d.

Measure the resistance and waveform according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J5-1 (CV+) - J5-4 (CGND) O - BR Video signal Ignition switch ON, shift lever in R, camera lens not covered, displaying an image+ Pulse generation
(See waveform 1)
Ignition switch ON, shift lever in R, camera lens covered, blacking out screen Pulse generation
(See waveform 2)
J5-2 (CV-) - Body ground SB - Body ground Shielded ground Always Below 1 Ω

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the inner rear television camera assembly with the connector connected.



e.
E265840C03
0.823,2.073 1,2.073 1,2.073 1.125,1.583 false 1.479,2.063 1.344,2.063 1.344,2.063 1.229,1.479 false 0.781,4.167 0.958,4.167 0.958,4.167 1.156,3.594 false 1.521,4.125 1.385,4.125 1.385,4.125 1.271,3.542 false 0.229,0.229 0.542,0.427 0.313,0.198 10 *a 0.396,1.052 0.76,1.313 0.365,0.26 10 GND 0.396,3.208 0.76,3.469 0.365,0.26 10 GND 0.26,2.271 0.625,2.531 0.365,0.26 10 *b 0.646,4.073 1.01,4.333 0.365,0.26 10 *c 0.656,1.979 1.021,2.24 0.365,0.26 10 *c 1.51,1.969 1.875,2.229 0.365,0.26 10 *d 1.542,4.052 1.906,4.313 0.365,0.26 10 *d
*a Waveform 1
*b Waveform 2
*c Synchronization Signal
*d Video Waveform


Reference (Oscilloscope waveform):

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the inner rear view mirror assembly with the connector connected.


i.

Waveform 1

Item Content
Terminal No. (Symbol) J5-1 (CV+) - J5-4 (CGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Ignition switch ON, shift lever in R, camera lens not covered, displaying an image

HINT:

The video waveform changes according to the image sent by the rear television camera assembly.



ii.

Waveform 2

Item Content
Terminal No. (Symbol) J5-1 (CV+) - J5-4 (CGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Ignition switch ON, shift lever in R, camera lens covered, blacking out screen

HINT:

The video waveform changes according to the image sent by the rear television camera assembly.