Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM › from 2019.03
RM2090E _56 Audio / Visual / Telematics _082076 PARK ASSIST / MONITORING _0396236 REAR VIEW MONITOR SYSTEM J

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM  Inner Rear View Mirror Power Source Circuit  


DESCRIPTION

This circuit detects the state of the ignition switch, and sends it to the inner rear view mirror assembly.

WIRING DIAGRAM

E389365E03
1.292,1.281 4.615,1.583 3.323,0.302 10 false Instrument Panel Junction Block Assembly 1.292,1.104 1.719,1.396 0.427,0.292 10 false 3A 5.01,2.26 7.125,2.635 2.115,0.375 10 false Inner Rear View Mirror Assembly 5.021,2.094 5.448,2.385 0.427,0.292 10 false K6 5.552,0.406 5.979,0.698 0.427,0.292 10 false 1 5.563,1.438 5.99,1.729 0.427,0.292 10 false 2 3.719,0.708 4.49,1.042 0.771,0.333 10 false UNIT IG1 1.813,0.552 3.333,0.979 1.521,0.427 10 false form IG1 NO. 2 Relay 4.844,0.417 5.271,0.708 0.427,0.292 10 false 5

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (INNER REAR VIEW MIRROR ASSEMBLY POWER SOURCE AND GROUND)
a.
E389368C02
1.49,0.177 1.906,0.427 0.417,0.25 1.604,0.229 2.042,0.542 0.438,0.313 10 false K6 0.198,0.125 0.635,0.438 0.438,0.313 10 false *a
*a Front view of wire harness connector
(to Inner Rear View Mirror Assembly)


Disconnect the K6 inner rear view mirror assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K6-1 - Body ground Ignition switch ON Below 1 V
Ignition switch off 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
K6-2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK AND REPLACE HARNESS AND CONNECTOR (INNER REAR VIEW MIRROR ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
2.CHECK AND REPLACE HARNESS AND CONNECTOR (INNER REAR VIEW MIRROR ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the K6 inner rear view mirror assembly connector.


b.

Disconnect the 3A instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K6-1 - 3A-5 Always Below 1 Ω
K6-1 or 3A-5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR