CHECK ECM
Measure the voltage according to the value(s) in the table below.
The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage for that pair of terminals, displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.
*1: w/ Rear Window Defogger
*2: w/o Multi Information Display
*3: w/ Supplemental Restraint System
*4: w/ Engine Immobilizer System
*5: w/o Engine Immobilizer System
*6: for Manual Transmission
*7: for Automatic Transmission
*8: w/o Heater
Waveform 1:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| C23-1 (#40) - C24-7 (E01) | 10 V/DIV, 1 msec./DIV | Idling |
| C23-2 (#30) - C24-7 (E01) | 10 V/DIV, 1 msec./DIV | Idling |
| C23-3 (#20) - C24-7 (E01) | 10 V/DIV, 1 msec./DIV | Idling |
| C23-4 (#10) - C24-7 (E01) | 10 V/DIV, 1 msec./DIV | Idling |
The wavelength becomes shorter as engine rpm increases.
Waveform 2:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| C23-6 (OCV+) - C23-5 (OCV-) | 5 V/DIV, 1 msec./DIV | Idling |
Waveform 3:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| C23-24 (PRG) - C24-7 (E01) | 10 V/DIV, 20 msec./DIV | Revving up |
If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.
Waveform 4:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| C24-8 (N2+) - C24-28 (N2-) | 2 V/DIV, 20 msec./DIV | Idling |
The wavelength becomes shorter as engine rpm increases.
Waveform 5:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| C24-9 (N+) - C24-29 (N-) | 2 V/DIV, 20 msec./DIV | Idling |
The wavelength becomes shorter as engine rpm increases.
Waveform 6:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| C24-11 (OX) - C24-33 (E2) | 0.2 V/DIV, 200 msec./DIV | Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor |
Waveform 7:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| C24-13 (KNK) - C24-33 (E2) | 1 V/DIV, 2 msec./DIV | Engine speed maintained at 4000 rpm after warming up engine |
Waveform 8:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| E3-2 (HCAN) - E3-1 (LCAN) | 1 V/DIV, 100 μsec./DIV | Idling |
The waveform varies depending on the CAN communication signal.
Waveform 9:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| E3-4 (CANH) - E3-3 (CANL) | 1 V/DIV, 100 μsec./DIV | Idling |
The waveform varies depending on the CAN communication signal.
Waveform 10:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| E3-13 (FROF) - E24-32 (E1) | 2 V/DIV, 500 μsec./DIV | Idling with warm engine |
If the airbag is deployed, a contact voltage is inputted to the ECM.
Waveform 11:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| E3-22 (SPD) - C24-32 (E1) | 2 V/DIV, 20 msec./DIV | Driving at 20 km/h (12 mph) |
The wavelength becomes shorter as vehicle speed increases.
Waveform 12:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| E3-24 (ATNE) - C24-32 (E1) | 5 V/DIV, 10 msec./DIV | Engine idling speed (When measured waveform 2000 rpm) |
The wavelength becomes shorter as engine rpm increases.
Waveform 13:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| E3-33 (REV) - C24-32 (E1) | 5 V/DIV, 10 msec./DIV | Idling |
The wavelength becomes shorter as engine rpm increases.