Home › Engine / Hybrid System › K3-VE ENGINE CONTROL › SFI SYSTEM › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002967 K3-VE ENGINE CONTROL _0014971 SFI SYSTEM C

K3-VE ENGINE CONTROL  SFI SYSTEM  P0350  Ignition System Circuit  P0351  Ignition Coil "A" Primary / Secondary Circuit  P0352  Ignition Coil "B" Primary / Secondary Circuit  P0353  Ignition Coil "C" Primary / Secondary Circuit  P0354  Ignition Coil "D" Primary / Secondary Circuit  


DESCRIPTION

HINT:
·

These DTCs indicate malfunctions relating to the primary circuit.

·

If DTC P0350 is stored, check the No. 1 to No. 4 ignition coil circuit.

·

If DTC P0351 is stored, check the No. 1 ignition coil circuit.

·

If DTC P0352 is stored, check the No. 2 ignition coil circuit.

·

If DTC P0353 is stored, check the No. 3 ignition coil circuit.

·

If DTC P0354 is stored, check the No. 4 ignition coil circuit.



A direct ignition system is used on this vehicle. The direct ignition system is a 1 cylinder ignition system which ignites one cylinder with one ignition coil. In the 1 cylinder ignition system, one spark plug is connected to the end of the secondary winding. High voltage is generated in the secondary winding and is applied directly to the spark plug. The spark of the spark plug passes from the center electrode to the ground electrode.

The ECM determines the ignition timing and transmits the ignition signals for each cylinder. Using the ignition signal, the ECM turns ON and OFF the power transistor inside the igniter, which switches ON and OFF a current to the primary coil. When the current to the primary coil is cut off, high voltage is generated in the secondary coil and this voltage is applied to the spark plugs to create sparks inside the cylinders.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0350 Ignition System Circuit Open in IG1 to 4 circuit from ignition coil assembly to ECM
(1 trip detection logic)
·

Open or short in IG circuit (1 to 4)

·

No. 1 to No. 4 ignition coil assembles

·

ECM


Comes on DTC stored
P0351 Ignition Coil "A" Primary / Secondary Circuit Open in IG1 circuit from ignition coil assembly to ECM
(1 trip detection logic)
·

Open or short in IG1 circuit

·

No. 1 ignition coil assembly

·

ECM


- DTC stored
P0352 Ignition Coil "B" Primary / Secondary Circuit Open in IG2 circuit from ignition coil assembly to ECM
(1 trip detection logic)
·

Open or short in IG2 circuit

·

No. 2 ignition coil assembly

·

ECM


- DTC stored
P0353 Ignition Coil "C" Primary / Secondary Circuit Open in IG3 circuit from ignition coil assembly to ECM
(1 trip detection logic)
·

Open or short in IG3 circuit

·

No. 3 ignition coil assembly

·

ECM


- DTC stored
P0354 Ignition Coil "D" Primary / Secondary Circuit Open in IG4 circuit from ignition coil assembly to ECM
(1 trip detection logic)
·

Open or short in IG4 circuit

·

No. 4 ignition coil assembly

·

ECM


- DTC stored

WIRING DIAGRAM

A262620E04
3.99,3.583 4.271,3.865 0.281,0.281 10 3 3.99,4.865 4.323,5.167 0.333,0.302 10 3 3.99,6.125 4.302,6.469 0.313,0.344 10 3 1.438,0.865 1.917,1.177 0.479,0.313 10 E28 1.438,1.01 3.146,1.448 1.708,0.438 10 IGNITION SWOTCH 1.573,0.469 2.094,0.792 0.521,0.323 10 AM2 2.354,0.469 2.875,0.844 0.521,0.375 10 IG2 1.406,0.469 1.844,0.823 0.438,0.354 10 5 2.677,0.469 3.104,0.823 0.427,0.354 10 6 3.729,0.719 4.344,1.094 0.615,0.375 10 E/G 2.677,2.5 3.042,2.781 0.365,0.281 10 4 3.99,2.344 4.302,2.667 0.313,0.323 10 3 2.25,2.885 2.792,3.26 0.542,0.375 10 C1 2.25,3.042 4.458,3.417 2.208,0.375 10 NO. 1 IGNITION COIL ASSEMBLY 2.677,3.458 2.979,3.75 0.302,0.292 10 1 2.677,2.198 3.083,2.646 0.406,0.448 10 1 2.677,3.74 3.021,4.083 0.344,0.344 10 4 2.25,4.146 2.802,4.469 0.552,0.323 10 C2 2.25,4.292 4.615,4.656 2.365,0.365 10 NO. 2 IGNITION COIL ASSEMBLY 2.677,4.719 2.781,4.875 0.104,0.156 10 1 2.677,5.021 3.021,5.385 0.344,0.365 10 4 2.25,5.417 2.792,5.729 0.542,0.313 10 C3 2.25,5.573 4.979,6.083 2.729,0.51 10 NO. 3 IGNITION COIL ASSEMBLY 2.677,5.979 3.146,6.448 0.469,0.469 10 1 2.677,6.281 2.99,6.594 0.313,0.313 10 4 2.25,6.677 2.885,7.083 0.635,0.406 10 C4 2.25,6.833 4.708,7.51 2.458,0.677 10 NO. 4 IGNITION COIL ASSEMBLY 0.417,3.177 0.948,3.5 0.531,0.323 10 AM2 0.417,5.396 1.354,5.729 0.938,0.333 10 FL MAIN 0.656,7.802 1.625,8.208 0.969,0.406 10 BATTERY 5.99,7.823 6.594,8.135 0.604,0.313 10 ECM 4.99,2.448 5.49,2.74 0.5,0.292 10 C23 5.333,2.333 5.792,2.677 0.458,0.344 10 IG1 5.333,3.594 5.792,3.906 0.458,0.313 10 IG2 5.323,4.854 5.813,5.198 0.49,0.344 10 IG3 5.333,6.125 5.875,6.646 0.542,0.521 10 IG4 5.333,6.927 5.833,7.313 0.5,0.385 10 E1 5.042,2.26 5.417,2.563 0.375,0.302 10 12 4.99,3.698 5.51,4.094 0.521,0.396 10 C23 5.042,3.521 5.417,3.896 0.375,0.375 10 11 4.99,4.979 5.49,5.323 0.5,0.344 10 C23 5.042,4.792 5.417,5.063 0.375,0.271 10 10 4.99,6.229 5.615,6.667 0.625,0.438 10 C23 5.083,6.042 5.479,6.365 0.396,0.323 10 9 4.99,6.938 5.635,7.417 0.646,0.479 10 C24 5.042,6.75 5.479,7.073 0.438,0.323 10 32 2.875,2.302 3.313,2.594 0.438,0.292 10 + 2.906,2.583 3.354,2.865 0.448,0.281 10 - 3.615,2.438 4.042,3.031 0.427,0.594 10 IGT 2.885,3.531 3.344,3.833 0.458,0.302 10 + 2.906,3.823 3.385,4.177 0.479,0.354 10 - 3.615,3.698 4.031,4.188 0.417,0.49 10 IGT 2.885,4.813 3.385,5.188 0.5,0.375 10 + 2.906,5.073 3.396,5.417 0.49,0.344 10 - 3.615,4.979 4.083,5.448 0.469,0.469 10 IGT 2.875,6.073 3.427,6.448 0.552,0.375 10 + 2.906,6.354 3.417,6.708 0.51,0.354 10 - 3.615,6.24 3.885,6.667 0.271,0.427 10 IGT

CAUTION / NOTICE / HINT

HINT:
·

Perform the spark test to determine the malfunctioning cylinder.

·

Read freeze frame data using an intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data at the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
a.

Disconnect the ignition coil assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C1-3 - C23-12 (IG1) Always Below 1 Ω
C2-3 - C23-11 (IG2) Always Below 1 Ω
C3-3 - C23-10 (IG3) Always Below 1 Ω
C4-3 - C23-9 (IG4) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C1-3 or C23-12 (IG1) - Body ground Always 10 kΩ or higher
C2-3 or C23-11 (IG2) - Body ground Always 10 kΩ or higher
C3-3 or C23-10 (IG3) - Body ground Always 10 kΩ or higher
C4-3 or C23-9 (IG4) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the ignition coil assembly connector.

Result:
Proceed to
OK
NG




OK

2.INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE)
a.
A200905C05
0.385,0.5 0.677,0.698 0.292,0.198 0.385,0.823 0.677,1.021 0.292,0.198 0.396,1.135 0.688,1.333 0.292,0.198 0.396,1.448 0.688,1.646 0.292,0.198 2.083,1.167 2.083,1.688 true 1.396,1.167 1.396,1.688 true 0.146,0.083 0.698,0.417 0.552,0.333 10 *a 0.448,0.521 0.927,0.823 0.479,0.302 10 C1 0.448,0.844 0.948,1.219 0.5,0.375 10 C2 0.448,1.156 0.906,1.531 0.458,0.375 10 C3 0.448,1.469 0.927,1.781 0.479,0.313 10 C4 2.063,1.729 2.458,2 0.396,0.271 10 - 1.365,1.729 1.823,2.01 0.458,0.281 10 +
*a Front view of wire harness connector
(to Ignition Coil Assembly)


Disconnect the ignition coil assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C1-4 (-) - Body ground Always Below 1 Ω
C2-4 (-) - Body ground Always Below 1 Ω
C3-4 (-) - Body ground Always Below 1 Ω
C4-4 (-) - Body ground Always Below 1 Ω



c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C1-1 (+) - C1-4 (-) Ignition switch ON 11 to 14 V
C2-1 (+) - C2-4 (-) Ignition switch ON 11 to 14 V
C3-1 (+) - C3-4 (-) Ignition switch ON 11 to 14 V
C4-1 (+) - C4-4 (-) Ignition switch ON 11 to 14 V



e.

Reconnect the ignition coil assembly connector.

Result:
Proceed to
OK
NG




OK

3.INSPECT ECM (IG1 - IG4 SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL - IGNITION SWITCH, IGNITION COIL - BODY GROUND)

3.INSPECT ECM (IG1 - IG4 SIGNAL)
a.
A141531C14
0.729,1 1.063,1.188 0.333,0.188 1.51,1 1.833,1.198 0.323,0.198 0.542,2.115 0.906,1.656 true 1.563,2.458 1.104,1.635 true 1.229,2.646 1.042,1.646 true 0.802,2.635 0.979,1.646 true 2.115,2.646 1.646,1.823 true 0.438,2.146 1.031,2.531 0.594,0.385 10 IG1 2.063,2.677 2.469,2.979 0.406,0.302 10 E1 1.49,2.469 2.156,2.833 0.667,0.365 10 IG4 1.188,2.677 1.927,3.135 0.74,0.458 10 IG3 0.698,2.677 1.344,3 0.646,0.323 10 IG2 0.208,0.146 0.729,0.542 0.521,0.396 10 *a 0.771,1.021 1.281,1.354 0.51,0.333 10 C23 1.542,1.021 1.979,1.313 0.438,0.292 10 C24
*a Component with harness connected
(ECM)


Connect the oscilloscope probes to the IG1 (IG2, IG3 and/or IG4) terminal and E1 terminal of the ECM connector.


b.
A141934

Check the waveform when the engine is idling or cranking.

Terminal No. (Symbol) Tool Setting Condition
C23-12 (IG1) - C24-32 (E1) 2 V/DIV, 50 msec./DIV Cranking or Idling
C23-11 (IG2) - C24-32 (E1) 2 V/DIV, 50 msec./DIV Cranking or Idling
C23-10 (IG3) - C24-32 (E1) 2 V/DIV, 50 msec./DIV Cranking or Idling
C23-9 (IG4) - C24-32 (E1) 2 V/DIV, 50 msec./DIV Cranking or Idling

OK:

The waveform exists in accordance with the engine speed.


HINT:
·

The waveforms shown in the illustration are at engine idling speed.

·

The oscilloscope waveform shown as an example does not include noise or chattering waveforms.

·

The waveform amplitudes differ slightly depending on the vehicle conditions.



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C




A

REPLACE IGNITION COIL ASSEMBLY

B

C