Home › Engine / Hybrid System › K3-VE ENGINE CONTROL › SFI SYSTEM › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002967 K3-VE ENGINE CONTROL _0014971 SFI SYSTEM C

K3-VE ENGINE CONTROL  SFI SYSTEM  P0325  Knock Sensor 1 Circuit  


DESCRIPTION

The flat type knock sensor (non-resonant type) has a structure that can detect vibration in a wider band of frequency from about 6 kHz to 15 kHz and has the following features:

·

The knock sensor is fitted on the cylinder block to detect engine knocking.

·

The sensor contains a piezoelectric element which generates voltage when it becomes deformed. This occurs when the cylinder block vibrates due to knocking. If engine knocking occurs, the ignition timing is retarded to suppress it.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0325 Knock Sensor 1 Circuit Open or short in knock sensor circuit for more than 0.9 seconds
(1 trip detection logic)
·

Open or short in knock sensor circuit

·

Knock sensor

·

Knock sensor installation

·

ECM


Comes on DTC stored

HINT:

If the ECM detects DTC P0325, it enters fail-safe mode in which the corrective retarded angle value is set to the maximum value.


Reference: Inspection using an oscilloscope

A149565N01
0.24,0.396 0.969,0.719 0.729,0.323 10 1 V/DIV 2.323,1.885 3.365,2.177 1.042,0.292 10 2 msec./DIV

Standard:
Tester Connection Tool Setting Condition Specified Condition
C24-13 (KNK) - C24-33 (E2) 1 V/DIV, 2 msec./DIV After warming up the engine, keep the engine speed at 4000 rpm The correct waveform is as shown

·

The oscilloscope waveform shown as an example does not include noise or chattering waveforms.

·

The waveform amplitudes differ slightly depending on the vehicle conditions.


WIRING DIAGRAM

A263581E03
5.49,1.01 6.01,1.479 0.521,0.469 10 KNK 5.49,2.156 6,2.51 0.51,0.354 10 E2 5.198,1.01 5.521,1.365 0.323,0.354 10 13 5.208,2.156 5.521,2.51 0.313,0.354 10 33 3.552,1.479 4.448,1.823 0.896,0.344 10 (Shielded) 2.344,1.01 2.833,1.448 0.49,0.438 10 2 1.354,1.01 1.76,1.344 0.406,0.333 10 1 1.302,1.698 2.667,2.094 1.365,0.396 10 KNOCK SENSOR 1.302,1.51 1.792,1.771 0.49,0.26 10 C13 5.854,3.427 6.333,3.75 0.479,0.323 10 ECM 5.854,3.219 6.552,3.563 0.698,0.344 10 C24

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - KNOCK SENSOR)
a.
A141561C02
1.51,0.573 1.833,0.75 0.323,0.177 1.417,2.792 1.594,2.25 true 2.125,2.781 1.719,2.083 true 1.292,2.833 1.948,3.219 0.656,0.385 10 E2 0.156,0.094 0.656,0.5 0.5,0.406 10 *a 2.01,2.813 2.688,3.167 0.677,0.354 10 KNK 1.552,0.594 2.01,0.917 0.458,0.323 10 C24
*a Rear view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C24-13 (KNK) - C24-33 (E2) 20°C (68°F) 120 to 280 kΩ



c.

Reconnect the ECM connector.

Result:
Proceed to
OK
NG




OK

2.INSPECT KNOCK SENSOR (SENSOR INSTALLATION)

NG

4.INSPECT KNOCK SENSOR (SENSOR RESISTANCE)
2.INSPECT KNOCK SENSOR (SENSOR INSTALLATION)
a.
A107018

Check the knock sensor installation.


Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)

Result:
Proceed to
OK
NG



OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0325)

NG

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0325)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>K3-VE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 206

e.

Start the engine.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 206

g.

Read DTCs.

Result:
Result Proceed to
No output A
P0325 (for LHD) B
P0325 (for RHD) C




A

B

C

4.INSPECT KNOCK SENSOR (SENSOR RESISTANCE)
a.

Inspect the knock sensor.

Click hereEngine / Hybrid System>K3-VE ENGINE CONTROL>KNOCK SENSOR>INSPECTION

Result:
Proceed to
OK
NG




OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (KNOCK SENSOR - ECM)

NG