Home › Engine / Hybrid System › 3SZ-VE ENGINE CONTROL › SFI SYSTEM(w/o Rear Heated Oxygen Sensor) › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002968 3SZ-VE ENGINE CONTROL _0014987 SFI SYSTEM(w/o Rear Heated Oxygen Sensor) C

3SZ-VE ENGINE CONTROL  SFI SYSTEM(w/o Rear Heated Oxygen Sensor)  P0505  Idle Control System Malfunction  


DESCRIPTION

The Idle Speed Control (ISC) valve is installed on the throttle body. During idling, it controls the engine speed by increasing or decreasing the air volume that bypasses the throttle valve, according to the signals received from the ECM.

The rotor built into the ISC valve rotates clockwise or counterclockwise by a fixed angle, in accordance with the signals from the ECM.

The rotor and valve are attached with a common screw, so the valve can only move forward or backward in proportion to the rotor revolutions. Thus, the intake air volume is controlled by changing the clearance between the valve and body.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0505 Idle Control System Malfunction Abnormality (open or short) has occurred in idle speed control actuation signal
(1 trip detection logic)
·

Open or short in idle speed control valve circuit

·

Idle speed control valve

·

ECM


Comes on DTC stored

HINT:

If the throttle body or ECM are changed, or a battery terminal is reconnected, be sure to initialize the ISC valve.

Follow the procedures below without depressing the accelerator pedal in order to perform the initialization:

·

Turn the ignition switch to ON (do not start the engine) and wait at least for 5 seconds.

·

Turn the ignition switch to OFF and wait for approximately 15 seconds.

·

Turn the ignition switch to ON again, and then start the engine.



WIRING DIAGRAM

A266591E02
1.74,0.667 2.344,1 0.604,0.333 10 IAHI 1.698,1.24 2.26,1.573 0.563,0.333 10 IALO 1.74,1.844 2.302,2.167 0.563,0.323 10 IBHI 1.698,2.417 2.188,2.656 0.49,0.24 10 IBLO 5.208,0.667 5.885,1.021 0.677,0.354 10 IAHI 5.208,1.24 5.844,1.573 0.635,0.333 10 IALO 5.208,1.823 5.854,2.156 0.646,0.333 10 IBHI 5.208,2.396 5.969,2.833 0.76,0.438 10 IBLO 2.156,0.583 2.635,1.177 0.479,0.594 10 3 2.156,1.156 2.49,1.51 0.333,0.354 10 1 2.156,1.74 2.49,2.094 0.333,0.354 10 4 2.156,2.313 2.479,2.677 0.323,0.365 10 2 4.927,0.594 5.385,0.969 0.458,0.375 10 15 4.927,1.156 5.406,1.542 0.479,0.385 10 14 4.927,1.74 5.354,2.052 0.427,0.313 10 17 4.927,2.313 5.271,2.573 0.344,0.26 10 16 0.271,3.031 0.875,3.375 0.604,0.344 10 C19 0.271,3.208 2.625,3.75 2.354,0.542 10 IDLE SPEED CONTROL VALVE 5.698,3.021 6.25,3.448 0.552,0.427 10 C23 5.698,3.229 6.354,3.688 0.656,0.458 10 ECM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed.

Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 206 32

e.

Read the value displayed on the intelligent tester.

Standard:

The engine speed is high with cold engine. Conversely, it falls with warm engine, and it is maintained at 750 rpm as an idle speed.


Result:
Proceed to
OK
NG




OK

NG

2.CHECK HARNESS AND CONNECTOR (IDLE SPEED CONTROL VALVE - ECM)
2.CHECK HARNESS AND CONNECTOR (IDLE SPEED CONTROL VALVE - ECM)
a.

Disconnect the idle speed control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C19-3 (IAHI) - C23-15 (IAHI) Always Below 1 Ω
C19-1 (IALO) - C23-14 (IALO) Always Below 1 Ω
C19-4 (IBHI) - C23-17 (IBHI) Always Below 1 Ω
C19-2 (IBLO) - C23-16 (IBLO) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C19-3 (IAHI) or C23-15 (IAHI) - Body ground Always 10 kΩ or higher
C19-1 (IALO) or C23-14 (IALO) - Body ground Always 10 kΩ or higher
C19-4 (IBHI) or C23-17 (IBHI) - Body ground Always 10 kΩ or higher
C19-2 (IBLO) or C23-16 (IBLO) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the idle speed control valve connector.

Result:
Proceed to
OK
NG




OK

3.INSPECT IDLE SPEED CONTROL VALVE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT IDLE SPEED CONTROL VALVE
a.
A141558C01
1.073,1.479 1.365,1.646 true 1.104,2.333 1.375,2.042 true 2.021,1.667 2.344,1.49 true 2.063,2 2.333,2.292 true 0.729,1.396 1.365,1.667 0.635,0.271 10 IBLO 0.802,2.281 1.51,2.771 0.708,0.49 10 IBHI 2.385,1.406 3.135,1.75 0.75,0.344 10 IALO 2.375,2.25 2.969,2.573 0.594,0.323 10 IAHI 0.292,0.396 0.865,0.823 0.573,0.427 10 *a
*a Component without harness connected
(Idle Speed Control Valve)


Disconnect the idle speed control valve connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IAHI) - 1 (IALO) 27°C (81°F) 45.6 to 50.4 Ω
4 (IBHI) - 2 (IBLO) 27°C (81°F) 45.6 to 50.4 Ω



c.

Reconnect the idle speed control valve connector.

Result:
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C




A

B

C