Home › Engine / Hybrid System › 3SZ-VE ENGINE CONTROL › SFI SYSTEM(w/o Rear Heated Oxygen Sensor) › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002968 3SZ-VE ENGINE CONTROL _0014987 SFI SYSTEM(w/o Rear Heated Oxygen Sensor) C

3SZ-VE ENGINE CONTROL  SFI SYSTEM(w/o Rear Heated Oxygen Sensor)  P0335  Crankshaft Position Sensor "A" Circuit  


DESCRIPTION

The Crankshaft Position (CKP) sensor system consists of a CKP sensor plate and a pickup coil. The sensor plate has 30 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and magnet.

The sensor plate rotates and, as each tooth passes through the pickup coil, a pulse signal is created. The pickup coil generates 30 signals per engine revolution. Based on these signals, the ECM calculates the crankshaft position and engine RPM. Using these calculations, the fuel injection time and ignition timing are controlled.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0335 Crankshaft Position Sensor "A" Circuit No crankshaft position sensor signal to ECM for 2 seconds or more during starter ON
(1 trip detection logic)
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

No.1 crankshaft position sensor plate

·

ECM


Comes on DTC stored

WIRING DIAGRAM

A266588E03
0.677,1.906 2.458,2.552 1.781,0.646 10 CRANKSHAFT POSITION SENSOR 0.677,1.729 1.354,2.156 0.677,0.427 10 C10 1.99,0.833 2.281,1.156 0.292,0.323 10 1 1.99,1.323 2.354,1.813 0.365,0.49 10 2 2.927,1.729 4.115,2.271 1.188,0.542 10 (Shielded) 4.771,0.833 5.25,1.229 0.479,0.396 10 9 4.708,1.323 5.135,1.656 0.427,0.333 10 29 4.958,0.844 5.417,1.094 0.458,0.25 10 N+ 4.958,1.323 5.469,1.667 0.51,0.344 10 N- 5.417,2.229 6.198,2.792 0.781,0.563 10 ECM 5.417,2.042 6.021,2.354 0.604,0.313 10 C24

CAUTION / NOTICE / HINT

HINT:
·

If no problem is found through this diagnostic troubleshooting procedure, troubleshoot the engine mechanical system.

·

Check the engine speed. The engine speed can be checked by using an intelligent tester. To check, follow the operation below:

1.

Connect the intelligent tester to the DLC3.

2.

Start the engine.

3.

Turn the tester on.

4.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed.


The engine speed may be indicated as zero despite the engine revolving normally. This is caused by a lack of NE signals from the Crankshaft Position (CKP) sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed, if the CKP sensor output voltage is insufficient.


·

Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.



Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 206 32

PROCEDURE

1.INSPECT ECM (SENSOR OUTPUT VOLTAGE)
a.
A286350C01
1.552,0.458 1.865,0.656 0.313,0.198 1.948,1.271 1.74,1.948 true 1.948,1.104 2.49,1.927 true 1.76,4.177 3.344,4.604 1.583,0.427 10 20 msec./DIV 0.479,2.51 1.219,2.781 0.74,0.271 10 2 V/DIV 0.469,3.24 1.208,3.51 0.74,0.271 10 GND 1.635,2.01 2.01,2.281 0.375,0.271 10 N- 2.49,2.01 2.865,2.281 0.375,0.271 10 N+ 1.583,0.479 1.958,0.75 0.375,0.271 10 C24 0.198,0.167 0.51,0.365 0.313,0.198 10 *a
*a Component with harness connected
(ECM)


Connect the oscilloscope probes to the N+ terminal and N- terminal of the ECM connector.


b.

Check the waveform when the engine is idling or cranking.

Terminal No. (Symbol) Tool Setting Condition
C24-9 (N+) - C24-29 (N-) 2 V/DIV, 20 msec./DIV Idling

OK:

The waveform exists in accordance with the engine speed.


HINT:
·

The waveforms shown in the illustration are at engine idling speed.

·

The oscilloscope waveform shown as an example does not include noise or chattering waveforms.

·

The waveform amplitudes differ slightly depending on the vehicle conditions.

·

Failure grounding of the shielded wire may cause noise in waveforms.



Result:
Proceed to
OK
NG




OK

NG

2.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)
2.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)
a.

Inspect the crankshaft position sensor.

Click hereEngine / Hybrid System>3SZ-VE ENGINE CONTROL>CRANKSHAFT POSITION SENSOR>INSPECTION

Result:
Proceed to
OK
NG




OK

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C10-1 - C24-9 (N+) Always Below 1 Ω
C10-2 - C24-29 (N-) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C10-1 or C24-9 (N+) - Body ground Always 10 kΩ or higher
C10-2 or C24-29 (N-) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the crankshaft position sensor connector.

Result:
Proceed to
OK
NG




OK

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
a.
A286351E01
1.677,1.552 2.594,1.875 0.917,0.323 10 Clearance 2.438,1.823 3.354,2.146 0.917,0.323 10 Abnormal 0.333,1.813 1.25,2.135 0.917,0.323 10 Normal

Check the crankshaft position sensor installation.

OK:

Sensor is installed correctly.


Result:
Proceed to
OK
NG




OK

5.CHECK NO.1 CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE)

NG

5.CHECK NO.1 CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE)
a.

Check the teeth of the sensor plate.

OK:

Sensor plate does not have any cracks or deformation.


Result:
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C




A

REPLACE NO.1 CRANKSHAFT POSITION SENSOR PLATE

B

C