Home › Engine / Hybrid System › 3SZ-VE ENGINE CONTROL › SFI SYSTEM(w/o Rear Heated Oxygen Sensor) › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002968 3SZ-VE ENGINE CONTROL _0014987 SFI SYSTEM(w/o Rear Heated Oxygen Sensor) C

3SZ-VE ENGINE CONTROL  SFI SYSTEM(w/o Rear Heated Oxygen Sensor)  P0443  Evaporative Emission Control System Purge Control Valve Circuit  


DESCRIPTION

In order to reduce hydrocarbon (HC) emissions, evaporated fuel from the fuel tank is routed through the charcoal canister to the intake manifold for combustion in the cylinders.

The ECM changes the duty signal to the purge VSV in the Evaporative Emission (EVAP) system so that the intake of HC emissions is appropriate for the driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0443 Evaporative Emission Control System Purge Control Valve Circuit Malfunction in purge VSV circuit continues for 10 seconds or more under purge control operation
(1 trip detection logic)
·

Open or short in purge VSV circuit

·

Purge VSV

·

ECM


Comes on DTC stored

WIRING DIAGRAM

A262622E02
6.375,2.656 7.031,3.042 0.656,0.385 10 ECM 6.229,1.188 6.719,1.458 0.49,0.271 10 PRG 6.229,1.938 6.792,2.25 0.563,0.313 10 E01 5.854,1.198 6.26,1.479 0.406,0.281 10 C23 5.927,1 6.323,1.26 0.396,0.26 10 24 5.854,1.948 6.302,2.26 0.448,0.313 10 C24 5.969,1.75 6.427,2.031 0.458,0.281 10 7 4.156,1.49 4.792,1.844 0.635,0.354 10 C20 4.125,1.104 4.521,1.406 0.396,0.302 10 2 0.688,3.583 1.802,3.844 1.115,0.26 10 BATTERY 0.552,2.802 1.469,3.365 0.917,0.563 10 FL MAIN 0.531,1.781 1.198,2.281 0.667,0.5 10 AM2 2.031,1.781 2.458,2.115 0.427,0.333 10 EFI 2.583,1.51 3.594,1.865 1.01,0.354 10 EFI MAIN 2.042,0.917 2.563,1.344 0.521,0.427 10 E/G 0.76,0.708 1.313,1.031 0.552,0.323 10 AM2 1.49,0.708 2.01,1.042 0.521,0.333 10 IG2 0.604,1.156 1.313,1.594 0.708,0.438 10 E28 0.604,1.313 2.177,1.833 1.573,0.521 10 IGNITION SWITCH 0.583,0.708 0.927,1.063 0.344,0.354 10 5 1.802,0.708 2.125,1.063 0.323,0.354 10 6 2.469,0.708 2.792,1.031 0.323,0.323 10 2 3.229,0.708 3.583,1.063 0.354,0.354 10 1 2.469,1.094 2.865,1.438 0.396,0.344 10 3 3.229,1.104 3.729,1.51 0.5,0.406 10 5 4.156,1.656 5.333,2 1.177,0.344 10 PURGE VSV 4.927,1.104 5.281,1.385 0.354,0.281 10 1

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (VSV FOR PURGE CONTROL)
a.

Disconnect the vacuum hose of the purge VSV (canister side).


b.

Connect the intelligent tester to the DLC3.


c.

Start the engine.


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for Purge Control.

Powertrain > Engine > Active Test
Tester Display
Activate the VSV for Purge Control
50004 206 4

f.

Perform the active test.


g.
A141547C01
0.854,2.646 1.375,3.063 0.521,0.417 10 *a 2.365,2.646 2.708,2.99 0.344,0.344 10 *b
*a VSV is on
*b VSV is off


Check if the disconnected port applies suction to your finger when operating the purge VSV using the tester.

Standard:
Tester Operation Specified Condition
ON Applies suction to your finger
OFF Applies no suction to your finger


Result:
Proceed to
OK
NG




OK

NG

2.INSPECT ECM (PRG VOLTAGE)
2.INSPECT ECM (PRG VOLTAGE)
a.
A141531C05
0.656,1 1,1.167 0.344,0.167 1.469,1 1.813,1.167 0.344,0.167 0.781,1.74 0.604,2.458 true 1.365,1.542 1.656,2.469 true 1.563,2.49 2.021,2.823 0.458,0.333 10 E01 0.448,2.49 1.073,2.813 0.625,0.323 10 PRG 0.198,0.146 0.792,0.594 0.594,0.448 10 *a 0.708,1.01 1,1.167 0.292,0.156 10 C23 1.521,1 1.813,1.167 0.292,0.167 10 C24
*a Component with harness connected
(ECM)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C23-24 (PRG) - C24-7 (E01) Ignition switch ON 11 to 14 V


Result:
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C




A

3.INSPECT PURGE VSV

B

C

3.INSPECT PURGE VSV
a.

Inspect the purge VSV.

Click hereEngine / Hybrid System>3SZ-VE EMISSION CONTROL>PURGE VALVE>INSPECTION

Result:
Proceed to
OK
NG




OK

4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

NG

4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
a.

Disconnect the purge VSV connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C20-1 - C23-24 (PRG) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C20-1 or C23-24 (PRG) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the purge VSV connector.

Result:
Proceed to
OK
NG




OK

5.CHECK HARNESS AND CONNECTOR (PURGE VSV - EFI MAIN RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (PURGE VSV - EFI MAIN RELAY)
a.

Disconnect the purge VSV connector.


b.

Remove the EFI MAIN relay from the fuse block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C20-2 - EFI MAIN relay (5) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C20-2 or EFI MAIN relay (5) - Body ground Always 10 kΩ or higher



d.

Reinstall the EFI MAIN relay.


e.

Reconnect the purge VSV connector.

Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR