The Intake Air Temperature (IAT) sensor monitors the IAT. The IAT sensor has a built in thermistor with a resistance that varies according to the temperature of the intake air. When the IAT is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (see Fig. 1).
The IAT sensor is powered by a 5 V supply from the THA terminal of the ECM, via resistor R.
Resistor R and the IAT sensor are connected in series. When the resistance value of the IAT sensor changes, the voltage at terminal THA varies accordingly. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve drivability.
When DTC P0110 is set, the ECM enters fail-safe mode. During fail-safe mode, the ECM uses a constant value stored in the ECM memory as an intake air temperature sensor signal. Fail-safe mode continues until a pass condition is detected.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0110 | Intake Air Temperature Circuit | Open or short in intake air temperature sensor circuit for 0.5 seconds or more
(1 trip detection logic) |
·
Open or short in intake air temperature sensor circuit ·
Intake air temperature sensor ·
ECM |
Comes on | DTC stored |
When this DTC is set, check the intake air temperature using the intelligent tester. Enter the following menus: Powertrain / Engine / Data List / Intake Air.
| Temperature Displayed | Malfunction |
|---|---|
| -40°C (-40°F) or less | Open circuit |
| 140°C (284°F) or more | Short circuit |
| Tester Display |
|---|
| Intake Air |
If other DTCs relating to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / Intake Air.
| Tester Display |
|---|
| Intake Air |
Read the value displayed on the tester.
Same as actual intake air temperature.
| Result | Proceed to |
|---|---|
| -40°C (-40°F) or less | A |
| 140°C (284°F) or more | B |
| Same as actual intake air temperature | C |
If there is an open circuit, the tester indicates -40°C (-40°F) or less.
If there is a short circuit, the tester indicates 140°C (284°F) or more.
A
B
C
| *1 | Intake Air Temperature Sensor |
| *2 | ECM |
| *a | Front view of wire harness connector
(Intake Air Temperature Sensor) |
Disconnect the intake air temperature sensor connector.
Connect terminals THA and E2 of the intake air temperature sensor wire harness side connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / Intake Air.
| Tester Display |
|---|
| Intake Air |
Read the value displayed on the tester.
140°C (284°F) or more
Reconnect the intake air temperature sensor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the intake air temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C14-1 - C24-15 (THA) | Always | Below 1 Ω |
| C14-2 - C24-33 (E2) | Always | Below 1 Ω |
Reconnect the intake air temperature sensor connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Intake Air Temperature Sensor |
| *2 | ECM |
Disconnect the intake air temperature sensor connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / Intake Air.
| Tester Display |
|---|
| Intake Air |
Read the value displayed on the tester.
-40°C (-40°F) or less
Reconnect the intake air temperature sensor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the intake air temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connections | Condition | Specified Conditions |
|---|---|---|
| C14-1 or C24-15 (THA) - Body ground | Always | 10 kΩ or higher |
Reconnect the intake air temperature sensor connector.
Reconnect the ECM connector.
| Result | Proceed to |
|---|---|
| NG | A |
| OK (for LHD) | B |
| OK (for RHD) | C |
A
B
C