Home › Engine / Hybrid System › 3SZ-VE ENGINE CONTROL › SFI SYSTEM(w/o Rear Heated Oxygen Sensor) › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002968 3SZ-VE ENGINE CONTROL _0014987 SFI SYSTEM(w/o Rear Heated Oxygen Sensor) C

3SZ-VE ENGINE CONTROL  SFI SYSTEM(w/o Rear Heated Oxygen Sensor)  P0115  Engine Coolant Temperature Circuit  


DESCRIPTION

A thermistor is built into the Engine Coolant Temperature (ECT) sensor, of which the resistance value varies according to the ECT.

The structure of the sensor and its connection to the ECM are the same as those of the Intake Air Temperature sensor.

HINT:

When DTC P0115 is set, the ECM enters fail-safe mode. During fail-safe mode, the ECM uses a constant value stored in the ECM memory as an engine coolant temperature sensor signal and the radiator fan is switched ON. Fail-safe mode continues until a pass condition is detected.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0115 Engine Coolant Temperature Circuit Open or short in engine coolant temperature sensor circuit for 0.5 seconds or more (1 trip detection logic)
·

Open or short in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM


Comes on DTC stored

HINT:

When this DTC is set, check the engine coolant temperature using the intelligent tester. Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.


Temperature Displayed Malfunction
-40°C (-40°F) or less Open circuit
130°C (266°F) or more Short circuit

Powertrain > Engine > Data List
Tester Display
Coolant Temp
50003 206 28

WIRING DIAGRAM

A266585E04
0.333,2.208 2.958,2.75 2.625,0.542 10 ENGINE COOLANT TEMPERATURE SENSOR 0.333,1.979 1.063,2.354 0.729,0.375 10 C15 2.448,1.292 2.927,1.76 0.479,0.469 10 2 2.448,0.75 2.885,1.167 0.438,0.417 10 1 5.323,1.292 5.75,1.625 0.427,0.333 10 E2 5.323,0.75 5.875,1.156 0.552,0.406 10 THW 5.052,0.75 5.417,1.021 0.365,0.271 10 14 5.063,1.292 5.552,1.625 0.49,0.333 10 33 5.948,0.302 6.417,0.656 0.469,0.354 10 5 V 5.896,0.635 6.323,1.083 0.427,0.448 10 R 5.771,2.396 6.344,2.792 0.573,0.396 10 ECM 5.771,2.219 6.302,2.573 0.531,0.354 10 C24

CAUTION / NOTICE / HINT

HINT:
·

If other DTCs relating to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.

·

Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ENGINE COOLANT TEMPERATURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.

Powertrain > Engine > Data List
Tester Display
Coolant Temp
50003 206 28

e.

Read the value displayed on the tester.

Standard:

80°C to 100°C (176°F to 212°F) with warm engine.


Result:
Result Proceed to
-40°C (-40°F) or less A
130°C (266°F) or more B
80°C to 100°C (176°F to 212°F) C


HINT:
·

If there is an open circuit, the tester indicates -40°C (-40°F) or less.

·

If there is a short circuit, the tester indicates 130°C (266°F) or more.





A

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)
a.
A143421C01
0.677,2.771 1.052,2.938 0.375,0.167 0.719,1.75 1.156,2.073 0.438,0.323 10 *1 0.74,2.771 1.031,2.917 0.292,0.146 10 C15 2.646,1.729 3.073,2.073 0.427,0.344 10 *2 0.323,2.406 0.771,2.76 0.448,0.354 10 *a
*1 Engine Coolant Temperature Sensor
*2 ECM
*a Front view of wire harness connector
(Engine Coolant Temperature Sensor)


Disconnect the engine coolant temperature sensor connector.


b.

Connect terminals 1 and 2 of the engine coolant temperature sensor connector on the wire harness side.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the tester on.


f.

Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.

Powertrain > Engine > Data List
Tester Display
Coolant Temp
50003 206 28

g.

Read the value displayed on the tester.

Standard:

130°C (266°F) or more.



h.

Reconnect the engine coolant temperature sensor connector.

Result:
Proceed to
OK
NG




OK

CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE ENGINE COOLANT TEMPERATURE SENSOR

NG

3.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
3.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the engine coolant temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connections Condition Specified Conditions
C15-1 - C24-14 (THW) Always Below 1 Ω
C15-2 - C24-33 (E2) Always Below 1 Ω



d.

Reconnect the engine coolant temperature sensor connector.


e.

Reconnect the ECM connector.

Result:
Proceed to
OK
NG




OK

CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)
a.
A188268C02
0.698,0.802 1.198,1.167 0.5,0.365 10 *1 2.479,0.802 2.969,1.177 0.49,0.375 10 *2 2.479,1.719 2.99,2.073 0.51,0.354 10 THW 2.458,2.208 3.104,2.583 0.646,0.375 10 ETHW
*1 Engine Coolant Temperature Sensor
*2 ECM


Disconnect the engine coolant temperature sensor connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.

Powertrain > Engine > Data List
Tester Display
Coolant Temp
50003 206 28

f.

Read the value displayed on the tester.

Standard:

-40°C (-40°F) or less



g.

Reconnect the engine coolant temperature sensor connector.


Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the engine coolant temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connections Condition Specified Conditions
C15-1 or C24-14 (THW) - Body ground Always 10 kΩ or higher



d.

Reconnect the engine coolant temperature sensor connector.


e.

Reconnect the ECM connector.

Result:
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C




A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C