Home › Engine / Hybrid System › 3SZ-VE ENGINE CONTROL › SFI SYSTEM(w/o Rear Heated Oxygen Sensor) › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002968 3SZ-VE ENGINE CONTROL _0014987 SFI SYSTEM(w/o Rear Heated Oxygen Sensor) C

3SZ-VE ENGINE CONTROL  SFI SYSTEM(w/o Rear Heated Oxygen Sensor)  P0010  Camshaft Position "A" Actuator Circuit (Bank 1)  


DESCRIPTION

A149551E03
2.844,1.104 2.427,0.865 false 3.167,1.115 3.354,0.833 false 4.417,1.802 4.854,2.073 true 4.354,1.573 4.948,1.667 true 3.615,1.552 4.26,2.563 true 3.281,1.99 3.427,2.198 false 2.271,1.396 1.958,1.219 false 2.708,1.958 2.51,2.177 false 2.979,2 2.635,2.51 false 2.375,1.635 1.938,1.865 true 1.833,2.469 3.01,2.792 1.177,0.323 10 Oil Pressure 0.156,0.115 3.729,0.531 3.573,0.417 10 Camshaft Timing Oil Control Valve Assembly 2.167,2.167 2.823,2.594 0.656,0.427 10 Drain 1.5,1.125 2.25,1.542 0.75,0.417 10 Sleeve 1.5,1.781 2.188,2.24 0.688,0.458 10 Spring 3.448,2.208 4.021,2.604 0.573,0.396 10 Drain 1.375,0.74 2.719,1.125 1.344,0.385 10 (Advanced Side) 3.365,0.667 4.594,1.094 1.229,0.427 10 (Retarded Side) 4.292,2.51 5.417,2.792 1.125,0.281 10 Spool Valve 5.01,1.604 5.875,2.094 0.865,0.49 10 Plunger 4.906,2.01 5.521,2.396 0.615,0.385 10 Coil

This circuit operates the spool valve by means of the duty signal from the ECM so as to switch the oil passages to the advanced side or retarded side to activate the VVT controller (camshaft timing sprocket assembly). In this way, optimum valve timing is maintained.

When the engine is stopped, the camshaft timing oil control valve is set to the most retarded position.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0010 Camshaft Position "A" Actuator Circuit (Bank 1) Open or short in camshaft timing oil control valve circuit for 8 second or more
(1 trip detection logic)
·

Open or short in camshaft timing oil control valve circuit

·

Camshaft timing oil control valve assembly

·

ECM


Comes on DTC stored

WIRING DIAGRAM

A266584E02
0.281,1.99 2.396,2.729 2.115,0.74 10 CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY 0.281,1.802 0.854,2.156 0.573,0.354 10 C21 1.594,0.719 1.896,1.01 0.302,0.292 10 1 1.594,1.354 1.875,1.677 0.281,0.323 10 2 4.948,0.729 5.24,1 0.292,0.271 10 6 4.948,1.354 5.26,1.656 0.313,0.302 10 5 5.167,1.344 5.833,1.635 0.667,0.292 10 OCV- 5.167,0.708 5.75,1.052 0.583,0.344 10 OCV+ 5.51,2.281 5.875,2.615 0.365,0.333 10 ECM 5.51,2.115 6.042,2.469 0.531,0.354 10 C23

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC (DTC P0010)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear DTCs after recording the freeze frame data and DTCs.

Powertrain > Engine > Clear DTCs
50002 206

e.

Start the engine.


f.

Allow the engine to idle and check for DTCs.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 206

h.

Read DTCs.

Result:
Result Proceed to
P0010 A
No output B




A

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

B

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
a.

Inspect the camshaft timing oil control valve assembly.

Click hereEngine / Hybrid System>3SZ-VE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION

Result:
Proceed to
OK
NG




OK

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)
a.

Disconnect the camshaft timing oil control valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connections Condition Specified Conditions
C21-1 - C23-6 (OCV+) Always Below 1 Ω
C21-2 - C23-5 (OCV-) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connections Condition Specified Conditions
C21-1 or C23-6 (OCV+) - Body ground Always 10 kΩ or higher
C21-2 or C23-5 (OCV-) - Body ground Always 10 kΩ or higher



d.

Reconnect the camshaft timing oil control valve assembly connector.


e.

Reconnect the ECM connector.

Result:
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C




A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C