Home › Engine / Hybrid System › 3SZ-VE ENGINE CONTROL › SFI SYSTEM(w/ Rear Heated Oxygen Sensor) › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002968 3SZ-VE ENGINE CONTROL _0014988 SFI SYSTEM(w/ Rear Heated Oxygen Sensor) J

3SZ-VE ENGINE CONTROL  SFI SYSTEM(w/ Rear Heated Oxygen Sensor)  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, the battery voltage is applied to the coil, which closes the contact point of the EFI MAIN relay, and power is supplied to terminal +B1 of the ECM.

WIRING DIAGRAM

A263068E02
6.385,2.698 7.021,3 0.635,0.302 10 ECM 6.24,1.271 6.771,1.615 0.531,0.344 10 +B1 6.24,2.135 6.75,2.417 0.51,0.281 10 E1 5.875,1.26 6.406,1.625 0.531,0.365 10 C23 5.979,1.073 6.385,1.333 0.406,0.26 10 7 5.875,2.135 6.323,2.427 0.448,0.292 10 C24 5.938,1.948 6.375,2.208 0.438,0.26 10 32 0.698,3.646 1.76,3.979 1.063,0.333 10 BATTERY 0.573,2.854 1.521,3.333 0.948,0.479 10 FL MAIN 0.542,1.573 1.135,1.958 0.594,0.385 10 AM2 2.917,1.698 3.354,1.979 0.438,0.281 10 EFI 4.031,1.573 4.885,1.875 0.854,0.302 10 EFI MAIN 2.917,0.99 3.427,1.344 0.51,0.354 10 E/G 1.094,0.771 1.573,1.063 0.479,0.292 10 AM2 1.823,0.771 2.333,1.115 0.51,0.344 10 IG2 0.948,1.219 1.5,1.521 0.552,0.302 10 E28 0.948,1.385 2.344,1.688 1.396,0.302 10 IGNITION SWITCH 0.917,0.771 1.25,1.083 0.333,0.313 10 5 2.135,0.771 2.385,1.031 0.25,0.26 10 6 3.917,0.76 4.198,1.031 0.281,0.271 10 2 4.667,0.76 5.125,1.177 0.458,0.417 10 1 3.917,1.167 4.167,1.438 0.25,0.271 10 3 4.667,1.167 5.042,1.563 0.375,0.396 10 5

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following procedure.


PROCEDURE

1.INSPECT ECM (+B1 VOLTAGE)
a.
A141531C08
0.656,1.021 0.99,1.198 0.333,0.177 1.458,1.021 1.792,1.198 0.333,0.177 0.479,2.406 0.615,1.542 true 1.969,2.417 1.646,1.823 true 0.354,2.458 0.823,2.75 0.469,0.292 10 +B1 1.927,2.469 2.406,2.917 0.479,0.448 10 E1 0.177,0.167 0.75,0.563 0.573,0.396 10 *a 0.688,1.031 1.302,1.417 0.615,0.385 10 C23 1.51,1.031 2.188,1.438 0.677,0.406 10 C24
*a Rear view of wire harness connector
(to ECM)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C23-7 (+B1) - C24-32 (E1) Always 11 to 14 V


Result:
Proceed to
OK
NG




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the negative battery cable.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connections Condition Specified Conditions
C24-32 (E1) - Body ground Always Below 1 Ω



d.

Reconnect the ECM connector.


e.

Reconnect the negative battery cable.

Result:
Proceed to
OK
NG




OK

3.INSPECT EFI MAIN RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT EFI MAIN RELAY
a.
A167865N11
2,0.615 1.542,0.26 true 2.667,0.625 3.073,0.25 true 2.531,1.125 3.063,1.125 true 2.531,1.625 3.073,1.625 true 1.208,0.75 1.469,1.052 0.26,0.302 10 5 0.208,0.76 0.542,1.063 0.333,0.302 10 3 1.229,1.313 1.5,1.656 0.271,0.344 10 2 0.198,1.313 0.521,1.573 0.323,0.26 10 1 1.417,0.177 1.802,0.427 0.385,0.25 10 1 3.125,0.177 3.396,0.458 0.271,0.281 10 2 3.125,1.542 3.406,1.854 0.281,0.313 10 3 3.125,1.042 3.375,1.323 0.25,0.281 10 5

Remove the EFI MAIN relay from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 No battery voltage applied to terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage applied to terminals 1 and 2 Below 1 Ω



c.

Reinstall the EFI MAIN relay.

Result:
Proceed to
OK
NG




OK

4.CHECK HARNESS AND CONNECTOR (EFI MAIN RELAY - ECM)

NG

REPLACE EFI MAIN RELAY

4.CHECK HARNESS AND CONNECTOR (EFI MAIN RELAY - ECM)
a.

Remove the EFI MAIN relay from the instrument panel junction block.


b.

Disconnect the ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connections Condition Specified Conditions
EFI MAIN relay (5) - C23-7 (+B1) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connections Condition Specified Conditions
EFI MAIN relay (5) or C23-7 (+B1) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connectors.


e.

Reinstall the EFI MAIN relay.

Result:
Proceed to
OK
NG




OK

5.CHECK HARNESS AND CONNECTOR (EFI MAIN RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (EFI MAIN RELAY - BODY GROUND)
a.

Remove the EFI MAIN relay from the instrument panel junction block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connections Condition Specified Conditions
EFI MAIN relay (1) - Body ground Always Below 1 Ω



c.

Reinstall the EFI MAIN relay.

Result:
Proceed to
OK
NG




OK

6.CHECK HARNESS AND CONNECTOR (EFI MAIN RELAY VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (EFI MAIN RELAY VOLTAGE)
a.
A261741C01
0.729,0.042 1.198,0.406 0.469,0.365 10 *a 2.104,0.625 2.552,0.99 0.448,0.365 10 *1
*1 Fuse Block
*a EFI Relay Terminal


Remove the EFI MAIN relay from the instrument panel junction block.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
EFI MAIN relay (3) - Body ground Ignition switch ON 11 to 14 V



d.

Reinstall the EFI MAIN relay.

Result:
Proceed to
OK
NG




OK

7.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - EFI MAIN RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - EFI MAIN RELAY)
a.

Disconnect the ignition switch connector.


b.

Remove the EFI MAIN relay from the instrument panel junction block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connections Condition Specified Conditions
E28-6 (IG2) - EFI MAIN relay (2) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connections Condition Specified Conditions
E28-6 (IG2) or EFI MAIN relay (2) - Body ground Always 10 kΩ or higher



d.

Reinstall the EFI MAIN relay.


e.

Reconnect the ignition switch connector.

Result:
Proceed to
OK
NG




OK

8.INSPECT IGNITION SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT IGNITION SWITCH

OK

CHECK AND REPAIR HARNESS OR CONNECTOR (IGNITION SWITCH - POSITIVE BATTERY TERMINAL)

NG