While the engine is being cranked, the battery voltage is applied to terminal STA of the ECM.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0512 | Starter Request Circuit | Either of following condition met:
(1 trip detection logic) ·
Short in STA signal circuit for 31 seconds or more ·
Open in STA signal circuit when starting engine at vehicle speed of 0 km/h |
·
Open or short in starter signal circuit ·
Open or short in speedometer circuit ·
ECM ·
TCM* ·
ST Relay* ·
Park/neutral position switch assembly* |
Comes on | DTC stored |
*: for Automatic Transmission
Refer to DTC P0500 (See page Engine / Hybrid System>3SZ-VE ENGINE CONTROL>SFI SYSTEM(w/ Rear Heated Oxygen Sensor)>P0500).
Inspect the fuses for circuits related to this system before performing the following procedure.
This diagnostic flowchart is based on the premise that the engine is cranked normally. If the engine does not crank, proceed to the Problem Symptoms Table (See page Engine / Hybrid System>3SZ-VE ENGINE CONTROL>SFI SYSTEM(w/ Rear Heated Oxygen Sensor)>PROBLEM SYMPTOMS TABLE).
| *a | Component with harness connected
(ECM) |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connections | Condition | Specified Condition |
|---|---|---|
| E3-25 (STA) - C24-32 (E1) | Ignition switch ON | Below 1 V |
| E3-25 (STA) - C24-32 (E1) | Engine cranking | 6 V or more |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
Disconnect the ignition switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connections | Condition | Specified Conditions |
|---|---|---|
| E3-25 (STA) - E28-4 (ST) | Always | Below 1 Ω |
| Tester Connections | Condition | Specified Conditions |
|---|---|---|
| E3-25 (STA) or E28-4 (ST) - Body ground | Always | 10 kΩ or higher |
Disconnect the ignition switch connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ignition switch.
Click hereEngine / Hybrid System>3SZ-VE STARTING>IGNITION SWITCH>INSPECTION
| Proceed to |
|---|
| A |
| B |
| C |
A
B
C
Remove the ST relay from the fuse block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | No battery voltage applied to terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | Battery voltage applied to terminals 1 and 2 | Below 1 Ω |
Reinstall the ST relay.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST relay from the fuse block.
Disconnect the TCM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Starter relay (1) - E9-16 (STR) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Starter relay (1) or E9-16 (STR) - Body ground | Always | 10 kΩ or higher |
Reconnect the TCM connector.
Reinstall the ST relay.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ignition switch connector.
Remove the ST relay from the fuse block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E28-4 (ST) - ST relay (2) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E28-4 (ST) or ST relay (2) - Body ground | Always | 10 kΩ or higher |
Reinstall the ST relay.
Reconnect the ignition switch connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Refer to Automatic Transmission System / DTC P0705 procedure.
Click hereDrivetrain>A4Q AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>P0705
| Result | Proceed to |
|---|---|
| NG | A |
| OK (for LHD) | B |
| OK (for RHD) | C |
A
B
C
Disconnect the ignition switch connector.
Disconnect the starter connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connections | Condition | Specified Conditions |
|---|---|---|
| E28-4 (ST) - D3-1 | Always | Below 1 Ω |
| Tester Connections | Condition | Specified Conditions |
|---|---|---|
| E28-4 (ST) or D3-1 - Body ground | Always | 10 kΩ or higher |
Reconnect the starter connector.
Reconnect the ignition switch connector.
| Result | Proceed to |
|---|---|
| NG | A |
| OK (for LHD) | B |
| OK (for RHD) | C |
A
B
C