Home › Engine / Hybrid System › 3SZ-VE ENGINE CONTROL › SFI SYSTEM(w/ Rear Heated Oxygen Sensor) › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002968 3SZ-VE ENGINE CONTROL _0014988 SFI SYSTEM(w/ Rear Heated Oxygen Sensor) C

3SZ-VE ENGINE CONTROL  SFI SYSTEM(w/ Rear Heated Oxygen Sensor)  P0110  Intake Air Temperature Circuit  


DESCRIPTION

A286155E01
1.635,2.021 2.094,1.635 false 0.156,0.073 1.188,0.469 1.031,0.396 10 Fig. 1 0.156,0.385 1.552,0.813 1.396,0.427 10 Resistance 0.083,0.771 0.573,1.26 0.49,0.49 10 (kΩ) 2.156,1.51 3.292,1.885 1.135,0.375 10 Acceptable 1.365,4.281 2.5,4.656 1.135,0.375 10 Temperature 3.063,4.177 3.427,4.479 0.365,0.302 10 (°C) 3.063,4.396 3.417,4.656 0.354,0.26 10 (°F)

The Intake Air Temperature (IAT) sensor monitors the IAT. The IAT sensor has a built in thermistor with a resistance that varies according to the temperature of the intake air. When the IAT is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (see Fig. 1).

The IAT sensor is powered by a 5 V supply from the THA terminal of the ECM, via resistor R.

Resistor R and the IAT sensor are connected in series. When the resistance value of the IAT sensor changes, the voltage at terminal THA varies accordingly. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve drivability.

HINT:

When DTC P0110 is set, the ECM enters fail-safe mode. During fail-safe mode, the ECM uses a constant value stored in the ECM memory as an intake air temperature sensor signal. Fail-safe mode continues until a pass condition is detected.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0110 Intake Air Temperature Circuit Open or short in intake air temperature sensor circuit for 0.5 seconds or more
(1 trip detection logic)
·

Open or short in intake air temperature sensor circuit

·

Intake air temperature sensor

·

ECM


Comes on DTC stored

HINT:

When this DTC is set, check the intake air temperature using the intelligent tester or Techstream. Enter the following menus: Powertrain / Engine / Data List / Intake Air.

Temperature Displayed Malfunction
-40°C (-40°F) or less Open circuit
140°C (284°F) or more Short circuit


Powertrain > Engine > Data List
Tester Display
Intake Air
50003 206 35

WIRING DIAGRAM

A266585E03
0.552,2.167 2.948,2.75 2.396,0.583 10 INTAKE AIR TEMPERATURE SENSOR 0.552,1.99 1.219,2.344 0.667,0.354 10 C14 2.448,1.302 2.76,1.604 0.313,0.302 10 2 2.448,0.75 2.813,1.052 0.365,0.302 10 1 5.323,1.302 5.74,1.656 0.417,0.354 10 E2 5.323,0.74 5.885,1.063 0.563,0.323 10 THA 5.052,0.74 5.552,1.104 0.5,0.365 10 15 5.063,1.302 5.635,1.74 0.573,0.438 10 33 5.948,0.26 6.354,0.594 0.406,0.333 10 5 V 5.896,0.604 6.25,0.979 0.354,0.375 10 R 5.771,2.396 6.406,2.76 0.635,0.365 10 ECM 5.771,2.229 6.375,2.563 0.604,0.333 10 C24

CAUTION / NOTICE / HINT

HINT:
·

If other DTCs relating to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.

·

Read freeze frame data using the intelligent tester or Techstream. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER OR TECHSTREAM (INTAKE AIR TEMPERATURE)
a.

Connect the intelligent tester or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester or Techstream on.


d.

Enter the following menus: Powertrain / Engine / Data List / Intake Air.

Powertrain > Engine > Data List
Tester Display
Intake Air
50003 206 35

e.

Read the value displayed on the intelligent tester or Techstream.

Standard:

Same as actual intake air temperature.


Result:
Result Proceed to
-40°C (-40°F) or less A
140°C (284°F) or more B
Same as actual intake air temperature C


HINT:
·

If there is an open circuit, the tester indicates -40°C (-40°F) or less.

·

If there is a short circuit, the tester indicates 140°C (284°F) or more.





A

2.READ VALUE USING INTELLIGENT TESTER OR TECHSTREAM (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING INTELLIGENT TESTER OR TECHSTREAM (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING INTELLIGENT TESTER OR TECHSTREAM (CHECK FOR OPEN IN WIRE HARNESS)
a.
A286210C01
0.469,3.302 0.854,3.5 0.385,0.198 0.729,1.958 1.302,2.292 0.573,0.333 10 *1 2.635,1.969 3.177,2.333 0.542,0.365 10 *2 0.219,2.594 0.792,2.979 0.573,0.385 10 *a 0.531,3.313 1.104,3.698 0.573,0.385 10 C14 2.573,1.521 3.146,1.906 0.573,0.385 10 E2 2.542,1.063 3.115,1.448 0.573,0.385 10 THA
*1 Intake Air Temperature Sensor
*2 ECM
*a Front view of wire harness connector
(Intake Air Temperature Sensor)


Disconnect the intake air temperature sensor connector.


b.

Connect terminals THA and E2 of the intake air temperature sensor wire harness side connector.


c.

Connect the intelligent tester or Techstream to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester or Techstream on.


f.

Enter the following menus: Powertrain / Engine / Data List / Intake Air.

Powertrain > Engine > Data List
Tester Display
Intake Air
50003 206 35

g.

Read the value displayed on the intelligent tester or Techstream.

Standard:

140°C (284°F) or more



h.

Reconnect the intake air temperature sensor connector.

Result:
Proceed to
OK
NG




OK

CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE INTAKE AIR TEMPERATURE SENSOR

NG

3.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
3.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
a.

Disconnect the intake air temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C14-1 - C24-15 (THA) Always Below 1 Ω
C14-2 - C24-33 (E2) Always Below 1 Ω



d.

Reconnect the intake air temperature sensor connector.


e.

Reconnect the ECM connector.

Result:
Proceed to
OK
NG




OK

CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING INTELLIGENT TESTER OR TECHSTREAM (CHECK FOR SHORT IN WIRE HARNESS)
a.
A188268C01
0.729,0.958 1.24,1.365 0.51,0.406 10 *1 2.604,0.958 3.021,1.313 0.417,0.354 10 *2 2.479,1.729 3.094,2.083 0.615,0.354 10 THA 2.458,2.188 3.094,2.458 0.635,0.271 10 ETHA
*1 Intake Air Temperature Sensor
*2 ECM


Disconnect the intake air temperature sensor connector.


b.

Connect the intelligent tester or Techstream to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester or Techstream on.


e.

Enter the following menus: Powertrain / Engine / Data List / Intake Air.

Powertrain > Engine > Data List
Tester Display
Intake Air
50003 206 35

f.

Read the value displayed on the intelligent tester or Techstream.

Standard:

-40°C (-40°F) or less



g.

Reconnect the intake air temperature sensor connector.

Result:
Proceed to
OK
NG




OK

NG

5.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
5.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
a.

Disconnect the intake air temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connections Condition Specified Conditions
C14-1 or C24-15 (THA) - Body ground Always 10 kΩ or higher



d.

Reconnect the intake air temperature sensor connector.


e.

Reconnect the ECM connector.

Result:
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C




A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C