Home › Engine / Hybrid System › 3SZ-VE ENGINE MECHANICAL › CYLINDER HEAD GASKET › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002969 3SZ-VE ENGINE MECHANICAL _0014997 CYLINDER HEAD GASKET A

3SZ-VE ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


PROCEDURE

Hide 15100 1.REMOVE OIL PUMP ASSEMBLY

Hide 13520 2.REMOVE CAMSHAFT TIMING SPROCKET ASSEMBLY

A130113

a.

Using the hexagonal lobe of the camshaft, remove the camshaft timing sprocket assembly.


b.

Remove the camshaft timing sprocket assembly from the camshaft.


Hide 3.REMOVE CAMSHAFT

NOTICE:

In order to prevent interference of the valve with the piston when removing the camshaft, turn the crankshaft in the engine cranking direction by approximately 90° from the TDC/compression of the No. 1 cylinder.


a.
A137120N07
0.448,1.625 0.198,1.854 true 0.448,1.323 0.177,1.323 true 0.458,1.01 0.188,1.01 true 0.469,0.604 0.188,0.51 true 0.802,1.594 0.865,1.958 true 1.375,1.583 1.302,1.969 true 1.99,1.604 1.99,1.938 true 2.573,1.583 2.573,1.938 true 2.573,0.156 2.573,0.708 true 1.99,0.167 1.99,0.719 true 1.396,0.188 1.396,0.708 true 0.833,0.177 0.833,0.698 true 0.094,1.781 0.469,2.094 0.375,0.313 10 1 0.073,1.25 0.375,1.635 0.302,0.385 10 3 0.073,0.938 0.396,1.24 0.323,0.302 10 4 0.083,0.438 0.385,0.75 0.302,0.313 10 2 0.854,1.969 1.24,2.167 0.385,0.198 10 6 1.26,1.979 1.625,2.177 0.365,0.198 10 8 1.969,1.969 2.323,2.156 0.354,0.188 10 5 2.552,1.969 2.927,2.146 0.375,0.177 10 7 2.5,0.01 2.938,0.302 0.438,0.292 10 11 1.896,0.01 2.292,0.25 0.396,0.24 10 12 1.365,0.01 1.698,0.26 0.333,0.25 10 9 0.74,0.01 1.198,0.292 0.458,0.281 10 10

Remove the No. 1 camshaft bearing cap and No. 2 camshaft bearing cap in the sequence shown in the illustration.


Hide 13523 4.REMOVE CAMSHAFT TIMING GEAR OR SPROCKET

A137122

a.

Clamp No. 2 camshaft in a vise.


b.

Remove the 3 bolts and the camshaft timing gear or sprocket.

NOTICE:

Be careful not to damage the camshaft.



Hide 11101 5.REMOVE CYLINDER HEAD SUB-ASSEMBLY

A137155N03
0.531,0.729 0.531,0.229 true 1.688,1.979 1.688,1.479 true 2.271,1.979 2.271,1.469 true 0.51,1.99 0.51,1.469 true 1.083,1.969 1.083,1.469 true 1.094,0.729 1.094,0.219 true 1.698,0.719 1.698,0.208 true 2.26,0.719 2.26,0.229 true 2.844,0.719 2.844,0.229 true 2.906,1.427 3.188,1.427 true 0.5,0.052 0.854,0.313 0.354,0.26 10 4 1.615,1.99 2.031,2.167 0.417,0.177 10 10 2.24,1.99 2.563,2.167 0.323,0.177 10 5 3.229,1.354 3.396,1.646 0.167,0.292 10 3 0.469,2 0.802,2.167 0.333,0.167 10 2 1.052,1.99 1.469,2.177 0.417,0.188 10 8 1.052,0.042 1.375,0.292 0.323,0.25 10 6 1.656,0.042 2.01,0.281 0.354,0.24 10 9 2.219,0.042 2.563,0.323 0.344,0.281 10 7 2.802,0.042 3.135,0.281 0.333,0.24 10 1

a.

Using an 8 mm bi-hexagon wrench, loosen the cylinder head bolts in several steps in the sequence shown in the illustration. Then, remove the cylinder head bolts and washers.

NOTICE:
·

When removing the bolts, do not drop the washers into the engine.

·

Removing the cylinder head bolts in the wrong order may cause damage to the cylinder head sub-assembly.




Hide 11115 6.REMOVE CYLINDER HEAD GASKET

a.
A261535

Remove the cylinder head gasket.