Home › Engine / Hybrid System › K3-VE ENGINE MECHANICAL › CAMSHAFT › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002970 K3-VE ENGINE MECHANICAL _0015005 CAMSHAFT A

K3-VE ENGINE MECHANICAL  CAMSHAFT  INSTALLATION  


PROCEDURE

Hide 13511 1.INSTALL CAMSHAFT

NOTICE:

In order to prevent interference of the valve with the piston when installing the camshaft, turn the crankshaft in the engine cranking direction by approximately 90° from the TDC/compression of the No. 1 cylinder.


a.

Apply engine oil to the cam, cylinder head journal, and top of the valve lifter.


b.

Set the camshafts so the cam lobes of the No. 3 and No. 4 cylinders on the intake side (the camshaft) push the valve lifters, and the cam lobes of the No. 2 and No. 4 cylinders on the exhaust side (the camshaft No. 2) push the valve lifters.


c.
A285951N05
0.229,1.167 0.438,1.167 true 0.208,1.604 0.417,1.604 true 0.25,2.448 0.417,2.219 true 0.198,1.927 0.406,1.927 true 0.021,1.094 0.49,1.479 0.469,0.385 10 11 0.063,1.531 0.531,1.917 0.469,0.385 10 9 0.031,1.844 0.5,2.229 0.469,0.385 10 10 0.042,2.385 0.51,2.771 0.469,0.385 10 12 1.396,3.146 1.76,3.427 0.365,0.281 10 5 0.823,3.146 1.188,3.427 0.365,0.281 10 7 2,3.146 2.365,3.427 0.365,0.281 10 8 2.646,3.146 3.01,3.427 0.365,0.281 10 6 0.771,0.125 1.135,0.406 0.365,0.281 10 3 1.396,0.125 1.76,0.406 0.365,0.281 10 4 2.604,0.125 2.969,0.406 0.365,0.281 10 2 2,0.125 2.365,0.406 0.365,0.281 10 1

Examine the front marks and numbers on the No. 1 and No. 2 bearing caps and check the sequence order is as shown in the illustration. Then tighten the bolts uniformly in several steps in the sequence shown in the illustration.

Torque:
13 N*m (127 kgf*cm, 9 ft.*lbf)


d.
A143168

Temporarily install the camshaft timing sprocket assembly with the bolt.


e.

Temporarily install the camshaft timing gear or sprocket with one bolt.


f.

Install the chain so the matchmarks of the camshaft timing sprockets and the paint marks, which were marked before removing the chain, are aligned.

HINT:

First, install the chain onto either of the camshafts. Turn the camshaft to the right and left using the hexagonal lobe of the camshaft so the matchmark of the sprocket and the paint marks of the chain are aligned.



g.

Remove the 2.5 mm (0.098 in.) diameter hexagon wrench from the tensioner.

HINT:

Using the hexagonal lobe of the camshaft, slightly turn the camshaft to the left, then remove the 2.5 mm (0.098 in.) diameter hexagon wrench with the chain loose on the tensioner side.



h.

While holding the hexagonal lobe of the camshaft, tighten the bolt, which installs the camshaft timing sprocket assembly, to the specified torque.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


i.
A285952

Turn the crankshaft pulley clockwise and install the remaining 2 bolts to the camshaft timing gear or sprocket. Then tighten all 3 bolts to the specified torque.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


j.
A263227C06
2.052,0.958 2.573,1.229 true 2.615,1.188 3.01,1.531 0.396,0.344 10 *1
*1 Adhesive


Apply adhesive to 2 or 3 threads of the plug.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



k.

Using an 10 mm socket hexagon wrench, install the plug.

Torque:
17 N*m (168 kgf*cm, 12 ft.*lbf)

NOTICE:
·

Install the plug within 3 minutes after applying adhesive.

·

Do not start the engine within 1 hour after installation.




Hide 11304 2.INSTALL NO. 2 TIMING CHAIN OR BELT COVER

a.
A130122C06
1.177,1.354 1.104,1.646 true 1.021,1.646 1.417,2.042 0.396,0.396 10 *a
*a Seal Packing


Apply seal packing as illustrated.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent



b.

Install the No. 2 timing chain or belt cover with the 2 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
·

Remove any oil from the contact surface.

·

Install the No. 2 timing chain or belt cover within 3 minutes of applying the seal packing.

·

Do not start the engine for at least 2 hours after the installation.




Hide 11201 5.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A130123C03
0.656,0.688 0.49,1.083 true 0.385,1.135 0.802,1.521 0.417,0.385 10 *1
*1 Gasket


Set a cylinder head cover gasket to the gasket groove of the head cover, then insert a gasket into the boss on the center of the cylinder head cover sub-assembly.

NOTICE:

Securely insert the gasket until it comes into contact with the rib.



b.
A130124C03
0.781,1.125 2.375,0.729 2.375,0.729 0.615,0.802 true 2.375,0.729 2.365,0.719 2.365,0.719 1.302,0.396 true 2.146,0.417 2.375,0.719 false 2.448,0.688 2.865,1.063 0.417,0.375 10 *a
*a Seal Packing


Apply seal packing as illustrated.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


HINT:

The seal packing should have a width of 5 mm and a height of 2 mm.



c.
A285956N03
2.958,1.719 3.281,2.052 0.323,0.333 10 11 0.302,0.156 0.604,0.427 0.302,0.271 10 8 0.938,0.302 1.313,0.604 0.375,0.302 10 2 1.729,0.333 2.094,0.656 0.365,0.323 10 4 2.792,0.281 3.135,0.573 0.344,0.292 10 6 0.344,1.281 0.698,1.635 0.354,0.354 10 10 0.646,1.875 0.938,2.167 0.292,0.292 10 5 1.104,1.719 1.417,2.021 0.313,0.302 10 3 1.698,1.708 2,2.021 0.302,0.313 10 1 2.323,1.708 2.667,2.031 0.344,0.323 10 7 1.292,1.167 1.646,1.521 0.354,0.354 10 12 2.302,1.167 2.656,1.521 0.354,0.354 10 13 3.156,0.938 3.427,1.25 0.271,0.313 10 9

Install the cylinder head cover sub-assembly with the 11 bolts and 2 nuts.


d.

Tighten the bolts and nuts in several steps in the sequence shown in the illustration.

Torque:
for bolt : 12 N*m (122 kgf*cm, 9 ft.*lbf)
for nut : 9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 6.INSTALL ENGINE WIRE

Hide 16507 7.CONNECT RADIATOR PIPE SUB-ASSEMBLY

Hide 22268 8.INSTALL NO. 2 THROTTLE BODY BRACKET

Hide 12262 9.CONNECT NO. 2 VENTILATION HOSE

Hide 12261 10.CONNECT VENTILATION HOSE

Hide 17700 12.INSTALL AIR CLEANER ASSEMBLY

Hide 17881 13.INSTALL NO. 1 AIR CLEANER HOSE

Hide 14.INSPECT FOR ENGINE OIL LEAK

Hide 51443 15.INSTALL REAR ENGINE UNDER COVER (for Full Cover Type)

Hide 51441 16.INSTALL NO. 1 ENGINE UNDER COVER (for Full Cover Type)

Hide 51441D 17.INSTALL ENGINE UNDER COVER (for Half Cover Type)