Home › Engine / Hybrid System › K3-VE ENGINE MECHANICAL › ENGINE UNIT › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002970 K3-VE ENGINE MECHANICAL _0015010 ENGINE UNIT A

K3-VE ENGINE MECHANICAL  ENGINE UNIT  INSTALLATION  


PROCEDURE

Hide 16507 2.INSTALL RADIATOR PIPE SUB-ASSEMBLY

A130136

a.

Connect the No. 4 radiator hose.


b.

Install the radiator pipe sub-assembly with the 2 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 12312 3.INSTALL NO. 2 ENGINE MOUNTING BRACKET

A285969N02
0.865,0.844 1.26,1.125 0.396,0.281 10 A 2.448,0.708 2.844,0.99 0.396,0.281 10 C 0.813,1.302 1.208,1.583 0.396,0.281 10 D 2.656,1.229 3.052,1.51 0.396,0.281 10 B

a.

Temporarily tighten the bolt A.


b.

Tighten the bolts in the following order: B, C, D and A.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 12311 4.INSTALL NO. 1 FRONT ENGINE MOUNTING BRACKET RH

A285970N02
0.646,0.813 0.969,1.094 0.323,0.281 10 A 0.698,1.271 1.021,1.552 0.323,0.281 10 D 1.906,1.75 2.229,2.031 0.323,0.281 10 B 1.625,0.354 1.948,0.635 0.323,0.281 10 C

a.

Temporarily tighten the bolt A.


b.

Tighten the bolts in the following order: B, C, D and A.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 89615 5.INSTALL KNOCK CONTROL SENSOR

A285971N03
2.25,0.906 2.823,1.208 0.573,0.302 10 20° 2.51,1.104 3.083,1.406 0.573,0.302 10 15° 1.667,1.844 2.24,2.146 0.573,0.302 10 15°

a.

Install the knock control sensor with the nut as shown in the illustration.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 21591 6.INSTALL WATER BY-PASS PLATE

A130140

a.

Using a 6 mm socket hexagon wrench, install the water by-pass plate with the 2 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 16035 7.INSTALL WATER HOSE JOINT

A130139

a.

Connect No. 3 water by-pass hose to the water hose joint.


b.

Install the water hose joint with the bolt.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 23291 9.INSTALL INJECTOR VIBRATION INSULATOR

Hide 23250 10.INSTALL FUEL INJECTOR ASSEMBLY

Hide 23807 11.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 22267 12.INSTALL THROTTLE BODY BRACKET

a.

Install the throttle body bracket with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 16 ft.*lbf)


Hide 22210 13.INSTALL THROTTLE BODY ASSEMBLY

A285972N03
1.521,0.24 1.823,0.521 0.302,0.281 10 B 1.708,1.802 2.01,2.083 0.302,0.281 10 A 2.208,1.542 2.51,1.823 0.302,0.281 10 A

a.

Install the throttle body assembly with the 3 bolts.

Torque:
Bolt A : 21 N*m (214 kgf*cm, 16 ft.*lbf)

Torque:
Bolt B : 7.5 N*m (77 kgf*cm, 66 in.*lbf)


Hide 16100 14.INSTALL WATER PUMP ASSEMBLY

a.

Install a new gasket, then install the water pump assembly with the 2 nuts and 3 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 16173 15.INSTALL WATER PUMP PULLEY

a.

Using SST, hold the water pump pulley.

SST
09960-10010  (09962-01000, 09963-00600)


b.

Install the water pump pulley with the 3 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 16603A 16.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY

Hide 16631B 17.INSTALL IDLER PULLEY BRACKET

Hide 16630D 18.INSTALL IDLER PULLEY SUB-ASSEMBLY

Hide 11301K 19.INSTALL CRANKSHAFT POSITION SENSOR

a.

Install the crankshaft position sensor with the bolt.

Torque:
7.5 N*m (77 kgf*cm, 66 in.*lbf)


Hide 89422A 20.INSTALL ENGINE COOLANT TEMPERATURE SENSOR

a.

Install a new gasket onto the engine coolant temperature sensor.


b.

Using SST, install the engine coolant temperature sensor.

SST
09817-33190  

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 11101E 21.INSTALL CAMSHAFT POSITION SENSOR

A285973C03
1.969,1.573 2.521,1.885 0.552,0.313 10 *a
*a Apply a light coat of engine oil


a.

Apply a light coat of engine oil to the O-ring, then install the camshaft position sensor with the bolt.

Torque:
7.5 N*m (77 kgf*cm, 66 in.*lbf)

NOTICE:

Make sure that the O-ring is not cracked or jammed when installing.



Hide 22.INSTALL ENGINE WIRE

Hide 88431 23.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET (for LHD)

A268326E01
2.558,1.833 2.677,1.986 0.119,0.153 10 1 2.392,1.972 2.511,2.124 0.119,0.153 10 2 2.769,1.586 2.889,1.739 0.119,0.153 10 4 2.082,1.987 2.201,2.139 0.119,0.153 10 3

a.

Install the No. 1 compressor mounting bracket with the 4 bolts.

Torque:
28 N*m (288 kgf*cm, 21 ft.*lbf)

HINT:

Tighten the bolts in the order shown in the illustration.



Hide 22268 24.INSTALL NO. 2 THROTTLE BODY BRACKET

a.

Install the No. 2 throttle body bracket with the 2 bolts.

Torque:
7.5 N*m (77 kgf*cm, 66 in.*lbf)


Hide 12262 25.INSTALL NO. 2 VENTILATION HOSE

a.

Install the No. 2 ventilation hose.


Hide 12261 26.INSTALL VENTILATION HOSE

a.

Install the ventilation hose.


Hide 16331A 27.INSTALL THERMOSTAT

Hide 16321 28.INSTALL WATER INLET

a.

Install the water inlet with the bolt and nut.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


b.

Install the wiring harness clamp bracket with the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 16322 29.INSTALL WATER INLET PIPE

a.

Connect the No. 3 radiator hose to the water inlet pipe.


b.

Install the water inlet pipe with the 2 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 30.INSTALL FUEL TUBE SUB-ASSEMBLY

Hide 31.INSTALL NO. 2 FUEL PIPE CLAMP

Hide 16267 32.CONNECT NO. 3 WATER BY-PASS HOSE (w/ Heater)

a.

Connect the No. 1 fuel hose.


b.

Connect the No. 3 water by-pass hose and No. 2 water by-pass hose.


Hide 16261 33.CONNECT WATER BY-PASS HOSE (w/o Heater)

a.

Connect the 2 water by-pass hoses.


Hide 16261 34.CONNECT WATER BY-PASS HOSE (w/ Heater)

a.

Connect the 2 water by-pass hoses.


Hide 17167 37.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR