Home › Engine / Hybrid System › K3-VE ENGINE MECHANICAL › CYLINDER HEAD GASKET › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002970 K3-VE ENGINE MECHANICAL _0015006 CYLINDER HEAD GASKET A

K3-VE ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


PROCEDURE

Hide 15100 1.REMOVE OIL PUMP ASSEMBLY

Hide 13520 2.REMOVE CAMSHAFT TIMING SPROCKET ASSEMBLY

A130113

a.

Using the hexagonal lobe of the camshaft, remove the camshaft timing sprocket assembly.


b.

Remove the camshaft timing sprocket assembly from the camshaft.


Hide 3.REMOVE CAMSHAFT

NOTICE:

In order to prevent interference of the valve with the piston when removing the camshaft, turn the crankshaft in the engine cranking direction by approximately 90° from the TDC/compression of the No. 1 cylinder.


a.
A137120N06
0.438,1.615 0.188,1.813 true 0.417,1.323 0.188,1.323 true 0.427,1.01 0.219,1.01 true 0.458,0.594 0.177,0.5 true 0.813,1.646 0.813,1.927 true 1.375,1.646 1.375,1.958 true 2.01,1.646 2.01,1.958 true 2.594,1.646 2.594,1.958 true 2.563,0.177 2.563,0.677 true 1.99,0.188 1.979,0.698 true 1.396,0.188 1.396,0.688 true 0.823,0.177 0.823,0.688 true 0.063,1.75 0.385,2.063 0.323,0.313 10 1 0.042,1.24 0.406,1.552 0.365,0.313 10 3 0.073,0.938 0.406,1.24 0.333,0.302 10 4 0.052,0.406 0.406,0.74 0.354,0.333 10 2 0.802,1.948 1.094,2.167 0.292,0.219 10 6 1.375,1.958 1.615,2.177 0.24,0.219 10 8 1.958,1.958 2.208,2.177 0.25,0.219 10 5 2.542,1.958 2.802,2.177 0.26,0.219 10 7 2.49,0.021 2.885,0.365 0.396,0.344 10 11 1.917,0.01 2.281,0.354 0.365,0.344 10 12 1.365,0 1.729,0.323 0.365,0.323 10 9 0.74,0.01 1.063,0.344 0.323,0.333 10 10

Remove the No. 1 camshaft bearing cap and No. 2 camshaft bearing cap in the sequence shown in the illustration.


Hide 13523 4.REMOVE CAMSHAFT TIMING GEAR OR SPROCKET

A137122

a.

Clamp No. 2 camshaft in a vise.


b.

Remove the 3 bolts and the camshaft timing gear or sprocket.

NOTICE:

Be careful not to damage the camshaft.



Hide 11101 5.REMOVE CYLINDER HEAD SUB-ASSEMBLY

A137155N05
0.521,0.719 0.531,0.198 true 1.677,1.896 1.677,1.479 true 2.271,1.938 2.281,1.49 true 0.5,1.938 0.51,1.49 true 1.094,1.896 1.094,1.49 true 1.104,0.729 1.104,0.177 true 1.688,0.719 1.698,0.188 true 2.25,0.719 2.25,0.198 true 2.833,0.719 2.833,0.208 true 2.906,1.417 3.156,1.417 true 0.5,0.01 0.823,0.302 0.323,0.292 10 4 1.615,1.906 1.979,2.177 0.365,0.271 10 10 2.25,1.969 2.583,2.167 0.333,0.198 10 5 3.198,1.354 3.427,1.635 0.229,0.281 10 3 0.479,1.958 0.729,2.156 0.25,0.198 10 2 1.094,1.906 1.385,2.177 0.292,0.271 10 8 1.073,0 1.458,0.323 0.385,0.323 10 6 1.677,0 2.083,0.354 0.406,0.354 10 9 2.208,0.01 2.573,0.375 0.365,0.365 10 7 2.802,0.021 3.146,0.365 0.344,0.344 10 1

a.

Using an 8 mm bi-hexagon wrench, loosen the cylinder head bolts in several steps in the sequence shown in the illustration. Then, remove the cylinder head bolts and washers.

NOTICE:
·

When removing the bolts, do not drop the washers into the engine.

·

Removing the cylinder head bolts in the wrong order may cause damage to the cylinder head sub-assembly.




Hide 11115 6.REMOVE CYLINDER HEAD GASKET

a.
A261535

Remove the cylinder head gasket.