77201
1.INSTALL FUEL TANK INLET PIPE SUB-ASSEMBLY
| *a | White Paint Mark |
Install the fuel tank inlet pipe onto the fuel tank filler pipe shield.
A white paint mark should be on the fuel tank inlet pipe.
Tighten the 2 bolts in the sequence shown in the illustration.
Install the inlet pipe cover with the 2 clips.
Install the fuel tank cap.
77380
2.INSTALL FUEL CUT OFF VALVE ASSEMBLY
Install the fuel cut off valve onto the fuel tank as illustrated.
77013
3.INSTALL NO. 2 FUEL TANK BREATHER TUBE SUB-ASSEMBLY
| *a | Groove |
| *b | Protrusion |
Align the protrusion of the fuel tank with the groove of the fuel tank breather tube, then install the fuel tank breather tube with the 4 bolts.
77100B
4.INSTALL FUEL HOSE CLAMP
Install the clamp until it clicks.
77141B
5.INSTALL NO. 1 FUEL TANK FLANGE REINFORCEMENT
Install the 4 No. 1 fuel tank flange reinforcements to the fuel tank.
77631A
6.INSTALL CENTER LOWER FUEL TANK PROTECTOR
tighten the 3 bolts and the fuel tank protector.
77108B
7.INSTALL FUEL TANK FILLER CHECK VALVE SUB-ASSEMBLY
Install the filler check valve sub-assembly as shown in the illustration.
Insert the filler check valve until its claw fits into the spool.
The valve should smoothly open and close with its own weight after installing the valve.
77269A
8.INSTALL FUEL TANK BREATHER HOSE
| *1 | Tank Flange |
| *a | Tank Side |
| *b | 0 to 3 mm(0 to 0.12 in.) |
| *c | 2 to 7 mm(0.08 to 0.28 in.) |
| *d | Up |
| *e | Left |
Install the fuel tank breather hose onto the fuel tank.
Install the clip as illustrated.
77213B
9.INSTALL FUEL TANK TO FILLER PIPE HOSE
| *1 | Fuel Tank |
| *2 | Spacer |
| *3 | Tank Flange |
| *a | Tank Side |
| *b | Paint Mark |
| *c | 0 to 3 mm(0 to 0.12 in.) |
| *d | 2 to 10 mm(0.08 to 0.39 in.) |
| *e | Up |
| *f | Left |
Check that the fuel tank filler check valve is securely connected to the fuel tank.
Install the fuel tank to filler pipe hose onto the fuel tank.
The paint mark is around the middle of the hose.
Install the hose so the paint mark faces upward at the tank side.
Install the hose clamp as illustrated, then tighten it until it comes into contact with the spacer.
23210P
10.INSTALL FUEL PUMP WITH MOTOR AND BRACKET ASSEMBLY
77203A
11.INSTALL FUEL SUCTION TUBE SUB-ASSEMBLY
| *1 | Checker |
|
Push |
|
Pull out |
Align a new fuel suction tube (fuel tube connector) with the fuel pump tube, then push in the fuel suction tube until the retainer makes a click sound. Then pull out the checker.
If connecting the tubes is too tight, apply a light coat of gasoline to the tip of the fuel pump tube.
Check that there are no scratches or foreign matter around the connected parts of the fuel pump tube and fuel suction tube (fuel tube connector) before this work.
After connecting the fuel suction tube (fuel tube connector), check that the fuel pump tube and fuel suction tube are securely connected by pulling them.
Install the clamp onto the fuel tank.
Fit the fuel suction tube into the clamp.
77100
12.INSTALL FUEL TANK ASSEMBLY
Operate the transmission jack, then install the fuel tank onto the vehicle.
Tighten the 4 bolts in the sequence shown in the illustration.
Connect the fuel pump connector.
77269A
13.CONNECT FUEL TANK BREATHER HOSE
| *a | Inlet Pipe Side |
| *b | 0 to 3 mm(0 to 0.12 in.) |
| *c | 2 to 7 mm(0.08 to 0.28 in.) |
| *d | Up |
| *e | Left |
Connect the fuel tank breather hose to the fuel tank inlet pipe.
Install the clip as illustrated.
77213B
14.CONNECT FUEL TANK TO FILLER PIPE HOSE
| *1 | Spacer |
| *a | Inlet Pipe Side |
| *b | 2 to 15 mm(0.08 to 0.59 in.) |
| *c | 0 to 3 mm(0 to 0.12 in.) |
| *d | Up |
| *e | Left |
Connect the fuel tank to filler pipe hose to the fuel tank inlet pipe.
Install the hose clamp as illustrated, then tighten it until it comes into contact with the spacer.
77203A
15.CONNECT FUEL SUCTION TUBE SUB-ASSEMBLY
| *1 | Retainer |
|
Push |
|
Push |
Insert the fuel suction tube (fuel tube connector) until it comes into contact with the fuel main tube, then push in the retainer until it makes a click sound.
If connecting the tubes is too tight, apply a light coat of gasoline to the tip of the fuel main tube.
Check that there are no scratches or foreign matter around the connected parts of the fuel main tube and fuel suction tube (fuel tube connector) before this work.
After connecting the fuel suction tube (fuel tube connector), check that the fuel main tube and fuel suction tube are securely connected by pulling them.
77259C
16.CONNECT FUEL HOSE
Connect the fuel hose to the fuel tank to canister tube.
Install the clip as illustrated.
37100
17.TEMPORARILY TIGHTEN PROPELLER SHAFT ASSEMBLY
37100
18.FULLY TIGHTEN PROPELLER SHAFT ASSEMBLY
19.ADD FUEL
20.INSPECT FOR OIL LEAK
21.INSPECT FOR FUEL LEAK