1. DISCHARGE FUEL SYSTEM PRESSURE
2.DRAIN FUEL
Remove the drain plug, and drain the fuel into a container.
Clean the drain plug and install it with a new gasket.
37100
3.REMOVE PROPELLER SHAFT ASSEMBLY
77259C
4.DISCONNECT FUEL HOSE
Loosen the hose clamp, then disconnect the fuel hose from the fuel delivery hose.
77203A
5.DISCONNECT FUEL SUCTION TUBE SUB-ASSEMBLY
| *1 | Retainer |
| *2 | Fuel Tube Connector |
| *3 | Nylon Tube |
| *4 | O-ring |
| *5 | Fuel Main Tube |
|
Pinch |
|
Pull out |
Disengage the claws and push down the retainer as illustrated.
Pull the fuel suction tube (fuel tube connector) out of the fuel main tube.
Remove any dirt and foreign matter from the fuel tube connector.
Do not allow any scratches or foreign matter on the parts when disconnecting them as the fuel tube connector has O-rings that seal the fuel main tube.
Perform this work by hand. Do not use any tools.
Do not forcibly bend, twist or turn the nylon tube.
Protect the disconnected parts by covering them with a plastic bag after disconnecting the fuel tube connector.
As some pressure remains in the fuel line, use a piece of cloth to prevent gasoline splashes.
If the fuel tube connector and fuel main tube are stuck, pinch the fuel main tube and push and pull the fuel tube connector to release them.
77213B
6.DISCONNECT FUEL TANK TO FILLER PIPE HOSE
Loosen the hose clamp bolt, then disconnect the fuel tank to filler pipe hose.
77269A
7.DISCONNECT FUEL TANK BREATHER HOSE
Loosen the hose clamp, then disconnect the fuel tank breather hose from the fuel inlet pipe.
77100
8.REMOVE FUEL TANK ASSEMBLY
Disconnect the fuel pump connector.
Hold the fuel tank using a transmission jack.
Remove the 4 bolts.
Operate the transmission jack, then remove the fuel tank from the vehicle.
77203A
9.REMOVE FUEL SUCTION TUBE SUB-ASSEMBLY
Separate the fuel suction tube from the clamp.
Remove the clamp from the fuel tank.
| *1 | Retainer |
| *2 | O-ring |
| *3 | Nylon Tuber |
| *4 | Fuel Tube Connector |
| *5 | Pipe |
|
Pinch |
|
Pull out |
Pinch the retainer to unlock it as illustrated, then pull the fuel suction tube (fuel tube connector) out of the fuel pump tube.
Remove any dirt and foreign matter from the fuel tube connector.
Do not allow any scratches or foreign matter on the parts when disconnecting them as the fuel tube connector has O-rings that seal the fuel main tube.
Perform this work by hand. Do not use any tools.
Do not forcibly bend, twist or turn the nylon tube.
Protect the disconnected parts by covering them with a plastic bag after disconnecting the fuel tube connector.
As some pressure remains in the fuel line, use a piece of cloth to prevent gasoline splashes.
If the fuel tube connector and fuel main tube are stuck, pinch the fuel main tube and push and pull the fuel tube connector to release them.
Remove the retainer from the fuel pump tube.
If the retainer is removed from the fuel pump tube, be sure to replace the fuel suction tube with a new one.
23210P
10.REMOVE FUEL PUMP WITH MOTOR AND BRACKET ASSEMBLY
77213B
11.REMOVE FUEL TANK TO FILLER PIPE HOSE
Loosen the hose clamp bolt, then remove the fuel tank to filler pipe hose.
77269A
12.REMOVE FUEL TANK BREATHER HOSE
Loosen the hose clamp, then disconnect the fuel tank breather hose from the fuel tank.
77108B
13.REMOVE FUEL TANK FILLER CHECK VALVE SUB-ASSEMBLY
Remove the fuel tank check valve sub-assembly from the fuel tank.
77631A
14.REMOVE CENTER LOWER FUEL TANK PROTECTOR
Remove the 3 bolts and the fuel tank protector.
77141B
15.REMOVE NO. 1 FUEL TANK FLANGE REINFORCEMENT
Remove the 4 No. 1 fuel tank flange reinforcements from the fuel tank.
77100B
16.REMOVE FUEL HOSE CLAMP
Unfasten the claw, then remove the fuel hose clamp from the fuel tank.
77013
17.REMOVE NO. 2 FUEL TANK BREATHER TUBE SUB-ASSEMBLY
Remove the 4 bolts, then remove the fuel tank breather tube from the clamp.
77380
18.REMOVE FUEL CUT OFF VALVE ASSEMBLY
Remove the fuel cut off valve from the fuel tank.
77201
19.REMOVE FUEL TANK INLET PIPE SUB-ASSEMBLY
Remove the fuel tank cap.
Remove the 2 clips, then remove the inlet pipe cover.
Remove the 2 bolts, then pull the fuel tank inlet pipe out of the fuel tank filler pipe shield.