Home › Engine / Hybrid System › 3SZ-VE FUEL › FUEL SYSTEM › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002971 3SZ-VE FUEL _0015016 FUEL SYSTEM L

3SZ-VE FUEL  FUEL SYSTEM  PRECAUTION  


PRECAUTION


a.

Before working on the fuel system, disconnect the cable from the negative battery terminal.


b.

Do not work on the fuel system near any naked flames. Never smoke during the work.


c.

Keep rubber and leather parts away from gasoline.



DISCHARGE FUEL SYSTEM PRESSURE


CAUTION:
·

Before removing the fuel system parts, take precautions to prevent gasoline spillage.

·

As some pressure remains in the fuel line even after taking precautions to prevent gasoline spillage, use a piece of cloth to prevent gasoline splashes when disconnecting the fuel line.



a.

Remove the fuse box opening cover (See page Vehicle Interior>INTERIOR PANELS / TRIM>LOWER INSTRUMENT PANEL>REMOVAL).


b.
A261184C04
1.594,0.708 0.698,0.323 true 0.5,0.24 0.688,0.396 0.188,0.156 10 *1
*1 F/P relay


Remove the F/P relay from the fuse block assembly.


c.

Start the engine.


d.

After the engine has stopped on its own, turn the ignition switch off.


e.

Crank the engine again, and check that the engine does not start.


f.

Remove the fuel tank cap, and discharge the pressure in the fuel tank completely.


g.

Disconnect the cable from the negative battery terminal.


h.

Install the F/P relay onto the fuse block assembly.


i.


FUEL SYSTEM


a.

When disconnecting the high-pressure fuel line, a large amount of gasoline will splash. So take the following precautions.

i.

Take precautions to prevent gasoline spillage.


ii.

Place a container underneath the connection.


iii.

Disconnect the fuel suction tube from the fuel main tube (See page Engine / Hybrid System>3SZ-VE FUEL>FUEL TANK>REMOVAL).


iv.

Disconnect the fuel suction tube from the fuel pump tube (See page Engine / Hybrid System>3SZ-VE FUEL>FUEL TANK>REMOVAL).


v.

Drain the fuel remaining in the fuel suction tube.


vi.
A126529C03
1.774,1.44 1.612,1.705 false 1.524,3.792 1.363,4.056 false 1.486,1.738 1.672,1.9 0.186,0.161 10 *1 0.145,0.09 0.474,0.302 0.328,0.212 12 *A: 1.216,4.099 1.403,4.26 0.186,0.161 10 *1 0.145,2.331 0.474,2.542 0.328,0.212 12 *B:
*A Fuel Main Tube Side
*B Fuel Pump Tube Side
*1 Plastic Bag


Cover the disconnected fuel tube connector, fuel main tube and fuel pump tube with Plastic bags to prevent damage and the intrusion of foreign objects.



b.

Take the following precautions when removing the fuel tube connector (Type A).

i.

Check the fuel tube connector and fuel main tube for dirt and mud before removing the fuel tube connector.

If dirty, wipe it with a piece of cloth.


ii.
A265503C04
1.552,0.979 1.844,0.979 false 1.865,0.885 2.042,1.052 0.177,0.167 10 *1
*1 Retainer
V100135

Pinch
V100136

Pull out


Disengage the claw and push down the retainer as illustrated.


iii.

Pull the fuel tube connector out of the fuel main tube.


iv.
A126534

If the fuel tube connector and fuel main tube are stuck, pinch the fuel main tube, then push and pull the fuel tube connector to release and disconnect the fuel tube connector.

NOTICE:

Never use any tools.



v.

After removing the fuel tube connector, check the sealing surface of the fuel main tube for dirt and mud.

If dirty, wipe it with a piece of cloth.


vi.

Cover the disconnected fuel tube connector and fuel main tube with Plastic bags to prevent damage and the intrusion of foreign objects.



c.

Take the following precautions when installing the fuel tube connector (Type A).

i.
A265511C05
2.094,0.406 2.323,0.406 false 2.365,0.323 2.583,0.49 0.219,0.167 10 *1
*1 Retainer
V100135

Push


Insert the fuel tube connector until it comes into contact with the fuel main tube, then push in the retainer until it makes a "click" sound.

HINT:

If connecting the tubes is too light, coat of fresh engine oil to the tip of the fuel main tube.



ii.
A265504

After connecting the fuel tube connector, check that the fuel tube connector and fuel main tube are securely connected by pulling them.



d.

Take the following precautions when removing the fuel tube connector (Type B).

i.

Check the fuel tube connector and fuel pump tube for dirt and mud before removing the fuel tube connector.

If dirty, wipe it with a piece of cloth.


ii.
A126537C04
0.74,0.813 0.49,1.198 true 0.365,1.198 0.552,1.354 0.188,0.156 10 *1
*1 Retainer
V100135

Pinch
V100136

Pull out


Pinch the retainer as illustrated to unlock it, then pull the fuel tube connector out of the fuel pump tube.

NOTICE:

If the retainer is removed from the fuel pump tube, be sure to replace the fuel suction tube with a new one.



iii.
A126538

If the fuel tube connector and fuel pump tube are stuck, pinch the retainer, then push and pull the fuel tube connector to release and disconnect the fuel tube connector.

NOTICE:

Never use any tools.



iv.

After removing the fuel tube connector, check the sealing surface of the fuel pump tube for dirt and mud.

If dirty, wipe it with a piece of cloth.


v.

Cover the disconnected fuel tube connector and fuel pump tube with plastic bags to prevent damage and intrusion of foreign objects.



e.

Take the following precautions when installing the fuel tube connector (Type B).

i.
A265505C02
1.066,0.307 1.252,0.468 0.186,0.161 10 *1 1.541,0.744 1.256,0.461 false
*1 Retainer
V100135

Push
V100136

Pull out


Align a new fuel suction tube (fuel tube connector) with the fuel pump tube, then push in the fuel suction tube until the retainer makes a click sound. Then pull out the checker.

NOTICE:

If the retainer is removed from the fuel pump tube, be sure to replace the fuel suction tube with a new one.


HINT:

If connecting the tubes is too tight, apply a light coat of fresh engine oil to the tip of the fuel pump tube.



ii.
A265506

After connecting the fuel tube connector, check that the fuel tube connector and fuel pump tube are securely connected by pulling them.



f.

Observe the following precautions when removing the fuel tube connector.

i.
A261185

Remove the No. 2 fuel pipe clamp.


ii.

Check for dirt or other foreign matter on the parts to be disconnected and clean them if necessary.


iii.
A159424C08
2.542,1.479 2.677,1.188 2.677,1.188 2.469,1.26 true 2.25,3.042 2.625,3.385 true 2.177,3.729 2.115,3.938 2.115,3.938 2.01,3.74 true 2.698,1.063 3.302,1.417 0.604,0.354 10 *1 2.104,2.938 2.281,3.094 0.177,0.156 10 *1 2.031,3.969 2.198,4.146 0.167,0.177 10 *2
*1 Retainer
*2 O-ring
V100135

Pinch
V100136

Pull


Pinch the retainer of the fuel tube connector, and then pull out the fuel tube connector to disconnect the fuel tube from the fuel pipe.

NOTICE:

Do not use any tools.



iv.
A193370C07
3.125,2.125 3.323,2.125 false
V100135

Pull
V100136

Push


If the connector and pipe are stuck, pinch the retainer with your hand, and then push and pull the connector to disconnect them.

NOTICE:

Do not use any tools.



v.

Check for dirt or other foreign matter on the parts to be disconnected and clean them if necessary.


vi.
A158902C09
1.219,1.635 1.729,1.271 true 1.063,1.615 1.229,1.781 0.167,0.167 10 *1
*1 Plastic Bag


Protect the contact surface by covering it with a plastic bag.

NOTICE:

Do not damage the pipe or fuel tube connector, and prevent entry of foreign objects.




g.
A125134C03
3.146,2.104 3.333,2.104 false
V100135

Push


Observe the following precautions when connecting the fuel tube connector.

i.

Check that there is no damage or foreign matter on the part of the pipe that comes into contact with the connector.


ii.

Align the axis of the connector with the axis of the pipe. Push the pipe into the connector until the connector makes a click sound. If the connection is too tight, apply a small amount of fresh engine oil to the tip of the pipe.


iii.
A125201C03
3.135,2.094 3.354,2.094 false
V100135

Pull


After connecting the pipe and connector, try to pull them apart to confirm that they are securely connected.


iv.
A261185

Install the No. 2 fuel pipe clamp.


v.

Inspect for fuel leaks.




INJECTOR


a.
A126531C03
1.271,2.208 1.271,2.542 false 0.938,0.76 1.125,0.24 false 1.135,1.052 1.281,0.563 false 3.052,1 3.24,1.156 0.188,0.156 10 *a 3.052,1.656 3.24,1.813 0.188,0.156 10 *b 3.052,2.323 3.24,2.479 0.188,0.156 10 *c 1.042,0.073 1.229,0.229 0.188,0.156 10 *1 1.188,0.396 1.375,0.552 0.188,0.156 10 *2 1.188,2.542 1.375,2.698 0.188,0.156 10 *3
*1 Fuel Injector
*2 O-ring
*3 Fuel Delivery Pipe
*a OK
*b NG
*c NG


Take the following precautions when removing and installing the fuel injectors.

i.

Do not reuse the O-ring.


ii.

Do not damage a new O-ring when installing it onto the fuel injector.


iii.

Before installing a new O-ring, appropriate lubricant or gasoline.

NOTICE:

Do not use engine oil, gear oil or brake oil.



iv.
A126532C04
1.719,1.552 2.438,1.635 true 2.333,0.677 2.667,0.99 false 2.396,0.375 2.219,0.083 false 2.063,0 2.25,0.156 0.188,0.156 10 *1 2.719,1 2.927,1.188 0.208,0.188 10 *2 2.458,1.552 2.646,1.708 0.188,0.156 10 *3
*1 Fuel Delivery Pipe
*2 O-ring
*3 Insulator


Install the fuel injector onto the fuel delivery pipe and cylinder head as illustrated.

NOTICE:

Apply appropriate lubricant or gasoline to the contact surface of the fuel delivery pipe before installing the fuel injector.





INSPECT FOR FUEL LEAK


a.

Check that there is no fuel leakage after doing maintenance on the fuel system.