Home › Engine / Hybrid System › K3-VE FUEL › FUEL TANK › 2011.11–2014.04
RM19Y0E _51 Engine / Hybrid System _002972 K3-VE FUEL _0015023 FUEL TANK A

K3-VE FUEL  FUEL TANK  INSTALLATION  


PROCEDURE

Hide 77201 1.INSTALL FUEL TANK INLET PIPE SUB-ASSEMBLY

a.
A265844C04
2.302,1.583 1.99,1.26 true 2.313,1.594 2.552,1.781 0.24,0.188 10 *a
*a White Paint Mark


Install the fuel tank inlet pipe onto the fuel tank filler pipe shield.

HINT:

A white paint mark should be on the fuel tank inlet pipe.



b.
A285399N02
0.313,1.313 0.469,1.51 0.156,0.198 10 1 1.479,1.51 1.635,1.708 0.156,0.198 10 2

Tighten the 2 bolts in the sequence shown in the illustration.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


c.

Install the inlet pipe cover with the 2 clips.


d.

Install the fuel tank cap.


Hide 77380 2.INSTALL FUEL CUT OFF VALVE ASSEMBLY

a.
A142203

Install the fuel cut off valve onto the fuel tank as illustrated.


Hide 77013 3.INSTALL NO. 2 FUEL TANK BREATHER TUBE SUB-ASSEMBLY

a.
A142204C04
2.333,1.438 2.594,1.521 true 2.135,1.458 1.948,1.74 false 1.865,1.76 2.135,1.958 0.271,0.198 10 *a 2.656,1.448 2.885,1.646 0.229,0.198 10 *b
*a Groove
*b Protrusion


Align the protrusion of the fuel tank with the groove of the fuel tank breather tube, then install the fuel tank breather tube with the 4 bolts.

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)


Hide 77100B 4.INSTALL FUEL HOSE CLAMP

a.

Install the clamp until it clicks.


Hide 77141B 5.INSTALL NO. 1 FUEL TANK FLANGE REINFORCEMENT

a.

Install the 4 No. 1 fuel tank flange reinforcements to the fuel tank.


Hide 77631A 6.INSTALL CENTER LOWER FUEL TANK PROTECTOR

a.

tighten the 3 bolts and the fuel tank protector.


Hide 77108B 7.INSTALL FUEL TANK FILLER CHECK VALVE SUB-ASSEMBLY

a.
A130592

Install the filler check valve sub-assembly as shown in the illustration.

NOTICE:
·

Insert the filler check valve until its claw fits into the spool.

·

The valve should smoothly open and close with its own weight after installing the valve.




Hide 77269A 8.INSTALL FUEL TANK BREATHER HOSE

a.
A142206C04
1.677,4.115 1.677,3.948 false 1.094,2.948 1.344,3.104 0.25,0.156 10 90° 1.604,4.115 1.792,4.271 0.188,0.156 10 *1 1.729,2.74 1.917,2.896 0.188,0.156 10 *d 0.906,3.313 1.125,3.49 0.219,0.177 10 *e 0.896,1.76 1.104,1.948 0.208,0.188 10 *b 1.552,1.76 1.76,1.948 0.208,0.188 10 *c 0.052,0.01 0.281,0.208 0.229,0.198 10 *a
*1 Tank Flange
*a Tank Side
*b 0 to 3 mm(0 to 0.12 in.)
*c 2 to 7 mm(0.08 to 0.28 in.)
*d Up
*e Left


Install the fuel tank breather hose onto the fuel tank.

NOTICE:

Install the clip as illustrated.



Hide 77213B 9.INSTALL FUEL TANK TO FILLER PIPE HOSE

a.
A142207C04
1.781,4.198 1.365,4.385 false 1.99,3.125 2.406,3 false 1.292,1.177 0.792,1.177 true 1.427,0.708 1.51,0.271 false 1.01,2.927 1.25,3.083 0.24,0.156 10 90° 2.469,2.896 2.656,3.052 0.188,0.156 10 *2 0.781,3.531 0.969,3.688 0.188,0.156 10 *f 0.573,1.094 0.76,1.25 0.188,0.156 10 *1 0.052,0.021 0.24,0.177 0.188,0.156 10 *a 1.156,4.333 1.344,4.49 0.188,0.156 10 *3 1.854,2.698 2.042,2.854 0.188,0.156 10 *e 1.448,0.083 1.635,0.24 0.188,0.156 10 *b 1.01,1.75 1.198,1.906 0.188,0.156 10 *c 1.667,1.76 1.854,1.917 0.188,0.156 10 *d
*1 Fuel Tank
*2 Spacer
*3 Tank Flange
*a Tank Side
*b Paint Mark
*c 0 to 3 mm(0 to 0.12 in.)
*d 2 to 10 mm(0.08 to 0.39 in.)
*e Up
*f Left


Check that the fuel tank filler check valve is securely connected to the fuel tank.


b.

Install the fuel tank to filler pipe hose onto the fuel tank.

HINT:
·

The paint mark is around the middle of the hose.



NOTICE:
·

Install the hose so the paint mark faces upward at the tank side.

·

Install the hose clamp as illustrated, then tighten it until it comes into contact with the spacer.




Hide 23210P 10.INSTALL FUEL PUMP WITH MOTOR AND BRACKET ASSEMBLY

Hide 77203A 11.INSTALL FUEL SUCTION TUBE SUB-ASSEMBLY

a.
A261543C08
2.188,0.781 2.969,0.333 true 2.979,0.219 3.167,0.375 0.188,0.156 10 *1
*1 Checker
V100135

Push
V100136

Pull out


Align a new fuel suction tube (fuel tube connector) with the fuel pump tube, then push in the fuel suction tube until the retainer makes a click sound. Then pull out the checker.

HINT:

If connecting the tubes is too tight, apply a light coat of gasoline to the tip of the fuel pump tube.


NOTICE:
·

Check that there are no scratches or foreign matter around the connected parts of the fuel pump tube and fuel suction tube (fuel tube connector) before this work.

·

After connecting the fuel suction tube (fuel tube connector), check that the fuel pump tube and fuel suction tube are securely connected by pulling them.




b.

Install the clamp onto the fuel tank.


c.

Fit the fuel suction tube into the clamp.


Hide 77100 12.INSTALL FUEL TANK ASSEMBLY

a.

Operate the transmission jack, then install the fuel tank onto the vehicle.


b.
A285400N02
0.5,1.094 0.656,1.292 0.156,0.198 10 1 1.677,1.906 1.833,2.104 0.156,0.198 10 4 1.542,0.719 1.698,0.917 0.156,0.198 10 3 2.667,1.542 2.813,1.74 0.146,0.198 10 2

Tighten the 4 bolts in the sequence shown in the illustration.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


c.

Connect the fuel pump connector.


Hide 77269A 13.CONNECT FUEL TANK BREATHER HOSE

a.
A142209C04
0.771,3.458 1.083,3.604 0.313,0.146 10 150° 1.375,3.396 1.615,3.542 0.24,0.146 10 15° 1.813,2.229 2,2.385 0.188,0.156 10 *d 0.594,2.948 0.781,3.104 0.188,0.156 10 *e 0.094,0.073 0.302,0.26 0.208,0.188 10 *a 0.844,1.344 1.042,1.521 0.198,0.177 10 *b 1.656,1.354 1.854,1.531 0.198,0.177 10 *c
*a Inlet Pipe Side
*b 0 to 3 mm(0 to 0.12 in.)
*c 2 to 7 mm(0.08 to 0.28 in.)
*d Up
*e Left


Connect the fuel tank breather hose to the fuel tank inlet pipe.

NOTICE:

Install the clip as illustrated.



Hide 77213B 14.CONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A142210C04
1.833,3.573 1.354,3.635 true 2.198,3.885 2.427,4.031 0.229,0.146 10 90° 2.271,3.469 2.51,3.615 0.24,0.146 10 60° 1.156,3.552 1.344,3.708 0.188,0.156 10 *1 1.771,2.271 1.958,2.427 0.188,0.156 10 *d 0.74,2.979 0.927,3.135 0.188,0.156 10 *e 0.073,0.052 0.26,0.208 0.188,0.156 10 *a 1.448,1.563 1.635,1.719 0.188,0.156 10 *b 2.25,1.563 2.438,1.719 0.188,0.156 10 *c
*1 Spacer
*a Inlet Pipe Side
*b 2 to 15 mm(0.08 to 0.59 in.)
*c 0 to 3 mm(0 to 0.12 in.)
*d Up
*e Left


Connect the fuel tank to filler pipe hose to the fuel tank inlet pipe.

NOTICE:

Install the hose clamp as illustrated, then tighten it until it comes into contact with the spacer.



Hide 77203A 15.CONNECT FUEL SUCTION TUBE SUB-ASSEMBLY

a.
A261575C04
2.396,1.521 1.781,1.896 true 1.604,1.813 1.792,1.969 0.188,0.156 10 *1
*1 Retainer
V100135

Push
V100136

Push


Insert the fuel suction tube (fuel tube connector) until it comes into contact with the fuel main tube, then push in the retainer until it makes a click sound.

HINT:

If connecting the tubes is too tight, apply a light coat of gasoline to the tip of the fuel main tube.


NOTICE:
·

Check that there are no scratches or foreign matter around the connected parts of the fuel main tube and fuel suction tube (fuel tube connector) before this work.

·

After connecting the fuel suction tube (fuel tube connector), check that the fuel main tube and fuel suction tube are securely connected by pulling them.




Hide 77259C 16.CONNECT FUEL HOSE

a.
A265845N02
1.462,2.571 1.778,2.733 0.316,0.161 10 45° 1.657,2.895 1.973,3.056 0.316,0.161 10 90°

Connect the fuel hose to the fuel tank to canister tube.

NOTICE:
·

Install the clip as illustrated.




Hide 37100 17.TEMPORARILY TIGHTEN PROPELLER SHAFT ASSEMBLY

Hide 19.ADD FUEL

Hide 20.INSPECT FOR OIL LEAK

Hide 21.INSPECT FOR FUEL LEAK