Home › Drivetrain › A4Q AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › 2011.11–2015.08
RM19Y0E _52 Drivetrain _002983 A4Q AUTOMATIC TRANSMISSION / TRANSAXLE _0015077 AUTOMATIC TRANSMISSION SYSTEM C

A4Q AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0705  Transmission Range Sensor Circuit Malfunction (PRNDL Input)  


DESCRIPTION

The Park/Neutral position switch detects the shift lever position and sends the signals to the TCM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Memory
P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) When the condition that the signal is not input is detected for more than a specified period.
(1 trip detection logic)
HINT:

The DTC P0705 is not stored in the system (only when trouble occurs, the code is output)


·

Open in Park/Neutral position switch circuit

·

Park/Neutral position switch

·

Transmission control switch

·

TCM


Come on Blinks DTC stored

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Memory
P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) 2 or more switches are ON simultaneously for more than a specified period for P, R, N, D, 3, 2 and L positions.
(1 trip detection logic)
·

Short in Park/Neutral position switch circuit

·

Park/Neutral position switch

·

Transmission control switch

·

TCM


Come on Blinks DTC stored

·

MIL:"Comes on" means the MIL (Malfunction IndicatorLamp) illuminates.

·

Memory:"DTC stored" means the TCM stores the trouble code if the ECU detects the DTC detection condition.


WIRING DIAGRAM

C246483E02
2.604,0.677 2.896,0.958 0.292,0.281 10 P 2.813,2.635 3.188,2.979 0.375,0.344 10 1 2.813,2.979 3.167,3.313 0.354,0.333 10 4 2.813,3.354 3.229,3.75 0.417,0.396 10 5 2.813,3.938 3.177,4.229 0.365,0.292 10 3 4.01,3.938 4.385,4.302 0.375,0.365 10 4 5.302,3.781 5.688,4.188 0.385,0.406 10 2 5.302,4.104 5.708,4.49 0.406,0.385 10 1 2.802,5.135 3.177,5.51 0.375,0.375 10 2 2.813,5.49 3.177,5.844 0.365,0.354 10 8 1.573,5.49 1.885,5.875 0.313,0.385 10 6 1.573,2.635 1.938,2.948 0.365,0.313 10 7 2.542,0.896 2.969,1.24 0.427,0.344 10 R+ 2.604,1.094 3.031,1.469 0.427,0.375 10 N 2.604,1.292 3.021,1.625 0.417,0.333 10 2 2.604,1.49 2.969,1.76 0.365,0.271 10 L 2.813,0.583 3.167,0.948 0.354,0.365 10 22 2.813,0.813 3.177,1.083 0.365,0.271 10 7 2.813,1 3.188,1.313 0.375,0.313 10 23 2.813,1.198 3.219,1.573 0.406,0.375 10 26 2.813,1.396 3.219,1.74 0.406,0.344 10 27 2.646,2.823 3,3.156 0.354,0.333 10 - 2.635,3.156 3.021,3.458 0.385,0.302 10 P 2.635,3.542 3.031,3.917 0.396,0.375 10 N 2.635,4.125 3,4.448 0.365,0.323 10 D 0.74,2.031 3.167,2.49 2.427,0.458 10 COMBINATION METER ASSEMBLY 1.75,2.823 2.104,3.156 0.354,0.333 10 + 2.635,5.313 2.938,5.625 0.302,0.313 10 2 2.635,5.688 3.01,5.99 0.375,0.302 10 L 1.75,5.688 2.25,6.042 0.5,0.354 10 E 1.052,6.146 3.521,6.521 2.469,0.375 10 PARK/NEUTRAL POSITION SWITCH 3.542,4.667 6.052,5.198 2.51,0.531 10 TRANSMISSION CONTROL SWITCH 4.188,4.156 4.781,4.573 0.594,0.417 10 NSSD 4.958,3.979 5.469,4.344 0.51,0.365 10 ATD 3.552,4.51 4.156,4.875 0.604,0.365 10 E18 0.74,1.875 1.219,2.208 0.479,0.333 10 E34 1.063,5.979 1.573,6.281 0.51,0.302 10 E23 5.844,2.719 6.229,3.042 0.385,0.323 10 E9 5.833,4.188 6.219,4.521 0.385,0.333 10 E9 5.802,3.854 6.292,4.188 0.49,0.333 10 E10 5.802,5.229 6.302,5.594 0.5,0.365 10 E10 5.802,5.573 6.333,5.948 0.531,0.375 10 E10 5.802,3.073 6.292,3.396 0.49,0.323 10 E10 5.802,3.427 6.406,3.792 0.604,0.365 10 E10 5.854,2.542 6.281,2.885 0.427,0.344 10 23 5.854,4.021 6.25,4.396 0.396,0.375 10 21 5.854,3.677 6.313,4.042 0.458,0.365 10 23 5.844,5.042 6.24,5.375 0.396,0.333 10 16 5.854,5.396 6.271,5.719 0.417,0.323 10 25 5.854,2.896 6.292,3.24 0.438,0.344 10 15 5.854,3.271 6.271,3.635 0.417,0.365 10 24 4.948,4.302 5.542,4.708 0.594,0.406 10 A/T3 6.146,3.094 6.521,3.458 0.375,0.365 10 P 6.156,2.74 6.479,3.073 0.323,0.333 10 R 6.156,3.448 6.531,3.823 0.375,0.375 10 N 6.167,3.885 6.552,4.229 0.385,0.344 10 D 6.156,5.229 6.49,5.573 0.333,0.344 10 2 6.156,5.583 6.479,5.948 0.323,0.365 10 L 6.156,4.219 6.896,4.583 0.74,0.365 10 ODCS 6.385,6.01 6.99,6.448 0.604,0.438 10 TCM 0.219,2.719 1.333,3.24 1.115,0.521 10 from IG1/BACK Fuse 0.073,0.063 2.417,0.542 2.344,0.479 12 w/o Multi Information Display:

C246484E02
2.792,1.219 3.135,1.542 0.344,0.323 10 - 2.771,1.896 3.083,2.198 0.313,0.302 10 P 2.771,2.26 3.135,2.563 0.365,0.302 10 N 2.771,2.844 3.125,3.135 0.354,0.292 10 D 1.885,1.219 2.208,1.5 0.323,0.281 10 + 2.771,4.156 3.094,4.49 0.323,0.333 10 2 2.771,4.542 3.156,4.906 0.385,0.365 10 L 2.979,1.021 3.313,1.344 0.333,0.323 10 1 2.969,1.698 3.281,2 0.313,0.302 10 4 2.958,2.063 3.344,2.375 0.385,0.313 10 5 2.969,2.646 3.354,2.969 0.385,0.323 10 3 3.865,2.646 4.219,2.99 0.354,0.344 10 4 5.167,2.49 5.458,2.802 0.292,0.313 10 2 5.167,2.813 5.458,3.094 0.292,0.281 10 1 2.969,3.969 3.333,4.333 0.365,0.365 10 2 2.969,4.344 3.313,4.646 0.344,0.302 10 8 1.875,4.531 2.271,4.885 0.396,0.354 10 E 1.698,1.031 2.031,1.323 0.333,0.292 10 7 1.677,4.333 2.01,4.656 0.333,0.323 10 6 1.177,5 3.604,5.417 2.427,0.417 10 PARK/NEUTRAL POSITION SWITCH 3.354,3.427 5.802,3.833 2.448,0.406 10 TRANSMISSION CONTROL SWITCH 4.031,2.875 4.625,3.25 0.594,0.375 10 NSSD 4.813,2.708 5.292,3.01 0.479,0.302 10 ATD 5.552,2.906 5.938,3.24 0.385,0.333 10 E9 5.563,2.573 5.927,2.875 0.365,0.302 10 E9 5.531,1.781 6,2.135 0.469,0.354 10 E10 5.521,2.156 5.958,2.49 0.438,0.333 10 E10 3.365,3.271 3.875,3.615 0.51,0.344 10 E18 5.51,4.063 5.948,4.427 0.438,0.365 10 E10 5.521,4.417 6.01,4.729 0.49,0.313 10 E10 1.188,4.833 1.656,5.125 0.469,0.292 10 E23 5.521,1.125 6,1.51 0.479,0.385 10 E10 5.573,2.74 5.917,3.01 0.344,0.271 10 21 5.573,2.396 5.979,2.688 0.406,0.292 10 23 5.563,1.615 5.958,1.917 0.396,0.302 10 15 5.563,1.979 5.958,2.271 0.396,0.292 10 24 5.563,3.885 5.948,4.167 0.385,0.281 10 16 5.563,4.229 6,4.563 0.438,0.333 10 25 5.563,0.938 5.969,1.24 0.406,0.302 10 23 4.792,3.021 5.302,3.333 0.51,0.313 10 A/T3 5.865,1.823 6.177,2.146 0.313,0.323 10 P 5.865,1.146 6.26,1.51 0.396,0.365 10 R 5.875,2.167 6.177,2.49 0.302,0.323 10 N 5.875,2.604 6.219,2.948 0.344,0.344 10 D 5.875,4.094 6.229,4.396 0.354,0.302 10 2 5.875,4.438 6.177,4.771 0.302,0.333 10 L 5.875,2.938 6.458,3.323 0.583,0.385 10 ODCS 6.094,4.958 6.781,5.375 0.688,0.417 10 TCM 0.354,1.115 1.521,1.854 1.167,0.74 10 from IG1/BACK Fuse 0.125,0.104 2.323,0.635 2.198,0.531 12 w/ Multi Information Display:

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - BODY GROUND)
a.

Disconnect the E23 park/neutral position switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E23-6 (E) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

2.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH)
C229187C01
0.365,1.031 0.854,1.323 0.49,0.292 1.865,1.344 2.302,1.844 true 0.052,0.063 0.438,0.365 0.385,0.302 10 *a 2.333,1.771 2.74,2.094 0.406,0.323 10 + 0.479,1.083 0.958,1.385 0.479,0.302 10 E23
*a Front view of wire harness connector
(to Park/Neutral Position Switch)


a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E23-7 (+) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


Result:
Proceed to
OK
NG




OK

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
C229188C01
0.875,0.583 1.365,0.896 true 1.156,0.26 1.604,0.875 true 1.844,0.875 2.198,0.271 true 2.542,0.573 2.104,0.906 true 0.854,1.313 1.333,1.219 true 1.448,1.823 1.625,1.271 true 2.073,1.833 1.875,1.271 true 2.104,1.208 2.552,1.333 true 0.115,0.094 0.458,0.396 0.344,0.302 10 *a 0.74,0.49 1.063,0.781 0.323,0.292 10 P 1.01,0.177 1.26,0.427 0.25,0.25 10 D 2.24,0.156 2.552,0.458 0.313,0.302 10 2 2.604,0.49 2.917,0.771 0.313,0.281 10 R 0.74,1.229 1.031,1.521 0.292,0.292 10 L 1.323,1.823 1.771,2.104 0.448,0.281 10 RB 2.01,1.844 2.354,2.177 0.344,0.333 10 E 2.604,1.26 2.885,1.51 0.281,0.25 10 N
*a Component without harness connected
(Park/Neutral Position Switch)


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
4 (P) - 6 (E) Shift lever in P Below 1 Ω
Shift lever not in P 10 kΩ or higher
1 (-) - 7 (+) Shift lever in R Below 1 Ω
Shift lever not in R 10 kΩ or higher
5 (N) - 6 (E) Shift lever in N Below 1 Ω
Shift lever not in N 10 kΩ or higher
3 (D) - 6 (E) Shift lever in D Below 1 Ω
Shift lever not in D 10 kΩ or higher
2 (2) - 6 (E) Shift lever in 2 Below 1 Ω
Shift lever not in 2 10 kΩ or higher
8 (L) - 6 (E) Shift lever in L Below 1 Ω
Shift lever not in L 10 kΩ or higher



b.

Reconnect the E23 park/neutral position switch connector.

Result:
Proceed to
OK
NG




OK

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TRANSMISSION CONTROL SWITCH)

NG

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TRANSMISSION CONTROL SWITCH)
a.

Disconnect the E18 transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E18-4 (NSSD) - Body ground Shift lever in D Below 1 Ω
Shift lever not in D 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - TCM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - TCM)
a.

Disconnect the E10 and E9 TCM connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E9-23 (D) - E18-2 (ATD) Always Below 1 Ω
E9-21 (ODCS) - E18-1 (A/T3) Always Below 1 Ω



c.

Reconnect the E10 and E9 TCM connectors.

Result:
Proceed to
OK
NG




OK

6.INSPECT TRANSMISSION FLOOR SHIFT ASSEMBLY (TRANSMISSION CONTROL SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT TRANSMISSION FLOOR SHIFT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
C250942C01
1.281,0.292 1.635,0.76 true 2.083,0.917 2.521,0.542 true 2.094,1.281 2.479,1.375 true 0.104,0.073 0.5,0.385 0.396,0.313 10 *a 0.917,0.208 1.344,0.531 0.427,0.323 10 ATD 2.563,0.448 3.01,0.771 0.448,0.323 10 AT3 2.552,1.302 3.135,1.604 0.583,0.302 10 NSSD
*a Component without harness connected
(Transmission Control Switch)


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (A/T3) - 4 (NSSD) Shift lever in D 10 kΩ or higher
Shift lever in 3 Below 1 V
2 (ATD) - 4 (NSSD) Shift lever in D Below 1 Ω
Shift lever in 3 10 kΩ or higher



b.

Reconnect the E18 transmission control switch connector.

Result:
Proceed to
OK
NG




OK

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH -TCM)

NG

REPLACE TRANSMISSION FLOOR SHIFT ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH -TCM)
a.

Disconnect the E34 combination meter connector.


b.

Disconnect the E10 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E10-15 (P) - Body ground Shift lever in P Below 1 Ω
Shift lever not in P 10 kΩ or higher
E10-24 (N) - Body ground Shift lever in N Below 1 Ω
Shift lever not in N 10 kΩ or higher
E10-16 (2) - Body ground Shift lever in 2 Below 1 Ω
Shift lever not in 2 10 kΩ or higher
E10-25 (L) - Body ground Shift lever in L Below 1 Ω
Shift lever not in L 10 kΩ or higher



d.

Reconnect the E10 TCM connector.


e.

Disconnect the E9 TCM connector.


f.

Turn the ignition switch to ON


g.
C246466C02
0.604,2.052 1.094,2.344 0.49,0.292 1.302,2.333 1.083,2.729 true 0.083,0.073 0.5,0.448 0.417,0.375 10 *a 0.635,2.677 1.292,3.021 0.656,0.344 10 23 (R) 0.74,2.115 1.198,2.49 0.458,0.375 10 E9
*a Rear view of wire harness connector
(to TCM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E9-23 (R) - Body ground Shift lever in R 11 to 14 V
Shift lever not in R Below 1 V



h.

Reconnect the E34 combination meter connector.


i.

Reconnect the E9 TCM connector.

Result:
Proceed to
OK
NG




OK

8.INSPECT COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT COMBINATION METER ASSEMBLY

Refer to the Meter /Gauge System.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

Result:
Proceed to
OK
NG



OK

NG

REPLACE COMBINATION METER ASSEMBLY