Home › Drivetrain › A4Q AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › 2011.11–2015.08
RM19Y0E _52 Drivetrain _002983 A4Q AUTOMATIC TRANSMISSION / TRANSAXLE _0015077 AUTOMATIC TRANSMISSION SYSTEM C

A4Q AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0778  Pressure Control Solenoid "B" Electrical (Shift Solenoid Valve SL2)  


DESCRIPTION

Shifting from 1st to 4th is performed in combination with ON and OFF operation of the shift solenoid valves SL1, SL2, SL3, SL, DSU and SR which is controlled by the TCM. If an open or short circuit occurs in any of the shift solenoid valves, the TCM controls the remaining normal shift solenoid valves to allow the vehicle to be operated smoothly (Fail-safe function).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Memory
P0778 Pressure Control Solenoid "B" Electrical (Shift Solenoid Valve SL2) When electricity is applied to the shift solenoid valve SL2, the condition that the current does not flow at all or overflow continues.
(1 trip detection logic)
·

Open or short in shift solenoid valve SL2 circuit

·

Shift solenoid valve SL2

·

TCM


Come on Blinks DTC stored

·

MIL:"Comes on" means the MIL (Malfunction IndicatorLamp) illuminates.

·

Memory:"DTC stored" means the TCM stores the trouble code if the ECU detects the DTC detection condition.


WIRING DIAGRAM

C246494E05
0.844,2.927 2.656,3.604 1.813,0.677 10 ECT SOLENOID (SHIFT SOLENOID VALVE SL2) 5.833,1.281 6.26,1.635 0.427,0.354 10 C2+ 5.833,2.219 6.313,2.583 0.479,0.365 10 C2- 6.052,2.927 6.625,3.302 0.573,0.375 10 TCM 2.344,1.188 2.75,1.531 0.406,0.344 10 H8 2.625,1.188 3.021,1.583 0.396,0.396 10 5 2.625,2.125 3.031,2.417 0.406,0.292 10 9 5.667,1.177 5.979,1.49 0.313,0.313 10 4 5.667,2.125 6.063,2.49 0.396,0.365 10 3 2.271,2.125 2.75,2.479 0.479,0.354 10 H12 0.854,2.771 1.375,3.094 0.521,0.323 10 E21 6.063,2.771 6.531,3.073 0.469,0.302 10 E10

PROCEDURE

1.INSPECT SOLENOID WIRE (SL2)
C130158C08
1.99,1.448 2.49,1.323 true 1.99,1.573 2.49,1.688 true 0.073,0.01 0.229,0.156 0.156,0.146 10 *a 2.521,1.229 3.177,1.583 0.656,0.354 10 5 (H8) 2.521,1.604 3.26,2 0.74,0.396 10 9 (H12)
*a Front view of wire harness connector
(to Solenoid wire)


a.

Disconnect the E21 solenoid wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
5 (H8) - 9 (H12) 20°C (68°F) 5.1 to 5.5 Ω
5 (H8) - Body ground Always 10 kΩ or higher
9 (H12) - Body ground Always 10 kΩ or higher



c.

Reconnect the E21 solenoid wire connector.

Result:
proceed to
OK
NG




OK

2.CHECK HARNESS AND CONNECTOR (SOLENOID WIRE - TCM)

NG

3.INSPECT SHIFT SOLENOID VALVE SL2
2.CHECK HARNESS AND CONNECTOR (SOLENOID WIRE - TCM)
a.

Disconnect the E10 TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
E10-4 (C2+) - E10-3 (C2-) 20°C (68°F) 5.1 to 5.5 Ω
E10-4 (C2+) - Body ground Always 10 kΩ or higher
E10-3 (C2-) - Body ground Always 10 kΩ or higher



c.

Reconnect the E10 TCM connector.

Result:
proceed to
OK
NG




OK

NG

REPAIR HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE SL2
D105552C03
1.188,0.688 1.521,0.927 true 2.021,0.698 1.729,0.927 true 1.229,2.844 1.563,3.083 true 2.052,2.844 1.76,3.073 true 0.125,0.104 0.458,0.438 0.333,0.333 10 *a 1.042,0.552 1.375,0.885 0.333,0.333 10 1 2.094,0.594 2.427,0.927 0.333,0.333 10 2 1.292,3.719 1.625,4.052 0.333,0.333 10 (-) 2.021,3.708 2.354,4.042 0.333,0.333 10 (+) 1.104,2.677 1.438,3.01 0.333,0.333 10 1 2.094,2.688 2.427,3.021 0.333,0.333 10 2 2.677,3.469 3.271,3.865 0.594,0.396 10 21W
*a Component without harness connected
(Shift Solenoid Valve SL2)


a.

Remove the shift solenoid valve SL2.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.1 to 5.5 Ω



c.

Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

NOTICE:
·

Never directly apply battery voltage to the solenoid valve connector (Do not allow a current of 1 A or more to flow). Perform the operation check via the specified bulb (resistance).

·

If a current of 1 A or more flows, the characteristic of the solenoid valve changes.

OK:

The solenoid valve makes an operating sound.




Result:
proceed to
OK
NG




OK

NG