Home › Drivetrain › A4Q AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › 2011.11–2015.08
RM19Y0E _52 Drivetrain _002983 A4Q AUTOMATIC TRANSMISSION / TRANSAXLE _0015077 AUTOMATIC TRANSMISSION SYSTEM C

A4Q AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0798  Pressure Control Solenoid "C" Electrical (Shift Solenoid Valve SL3)  


DESCRIPTION

Shifting from 1st to 4th is performed in combination with ON and OFF operation of the shift solenoid valves SL1, SL2, SL3, SL, DSU and SR which is controlled by the TCM. If an open or short circuit occurs in any of the shift solenoid valves, the TCM controls the remaining normal shift solenoid valves to allow the vehicle to be operated smoothly (Fail-safe function).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Memory
P0798 Pressure Control Solenoid "C" Electrical (Shift Solenoid Valve SL3) When electricity is applied to the shift solenoid valve SL3, the condition that the current does not flow at all or overflow continues.
(1 trip detection logic)
·

Open or short in shift solenoid valve SL3 circuit

·

Shift solenoid valve SL3

·

TCM


Come on Blinks DTC stored

·

MIL:"Comes on" means the MIL (Malfunction IndicatorLamp) illuminates.

·

Memory:"DTC stored" means the TCM stores the trouble code if the ECU detects the DTC detection condition.


WIRING DIAGRAM

C246494E06
0.771,2.865 2.563,3.552 1.792,0.688 10 ECT SOLENOID (SHIFT SOLENOID VALVE SL3) 6.052,2.865 6.615,3.229 0.563,0.365 10 TCM 2.354,1.188 2.74,1.469 0.385,0.281 10 H7 2.635,1.188 2.927,1.469 0.292,0.281 10 6 5.656,1.177 5.979,1.542 0.323,0.365 10 2 5.656,2.115 6.021,2.5 0.365,0.385 10 1 2.635,2.125 2.969,2.396 0.333,0.271 10 10 2.26,2.125 2.729,2.427 0.469,0.302 10 H11 6.073,2.698 6.521,3 0.448,0.302 10 E10 0.771,2.698 1.24,2.979 0.469,0.281 10 E21 5.844,1.271 6.458,1.667 0.615,0.396 10 C3B+ 5.833,2.208 6.458,2.604 0.625,0.396 10 C3B-

PROCEDURE

1.INSPECT SOLENOID WIRE (SL3)
C130158C06
1.792,1.448 2.531,1.229 true 1.792,1.573 2.531,1.771 true 0.073,0.01 0.479,0.354 0.406,0.344 10 *a 2.563,1.125 3.104,1.542 0.542,0.417 10 6 (H7) 2.563,1.688 3.354,2.083 0.792,0.396 10 10 (H11)
*a Front view of wire harness connector
(to Solenoid wire)


a.

Disconnect the E21 solenoid wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
6 (H7) - 10 (H11) 20°C (68°F) 5.1 to 5.5 Ω
6 (H7) - Body ground Always 10 kΩ or higher
10 (H11) - Body ground Always 10 kΩ or higher



c.

Reconnect the E21 solenoid wire connector.

Result:
proceed to
OK
NG




OK

2.CHECK HARNESS AND CONNECTOR (SOLENOID WIRE - TCM)

NG

3.INSPECT SHIFT SOLENOID VALVE SL3
2.CHECK HARNESS AND CONNECTOR (SOLENOID WIRE - TCM)
a.

Disconnect the E10 TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
E10-2 (C3B+) - E10-1 (C3B2-) 20°C (68°F) 5.1 to 5.5 Ω
E10-2 (C3B+) - Body ground Always 10 kΩ or higher
E10-1 (C3B-) - Body ground Always 10 kΩ or higher



c.

Reconnect the E10 TCM connector.

Result:
proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE SL3
D105552C04
1.188,0.688 1.521,0.927 true 2.021,0.698 1.729,0.927 true 1.229,2.844 1.563,3.083 true 2.052,2.844 1.76,3.073 true 0.125,0.104 0.458,0.438 0.333,0.333 10 *a 1.042,0.552 1.375,0.885 0.333,0.333 10 1 2.094,0.594 2.427,0.927 0.333,0.333 10 2 1.292,3.719 1.625,4.052 0.333,0.333 10 (-) 2.021,3.708 2.354,4.042 0.333,0.333 10 (+) 1.104,2.677 1.438,3.01 0.333,0.333 10 1 2.094,2.688 2.427,3.021 0.333,0.333 10 2 2.677,3.469 3.271,3.865 0.594,0.396 10 21W
*a Component without harness connected
(Shift Solenoid Valve SL3)


a.

Remove the shift solenoid valve SL3.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.1 to 5.5 Ω



c.

Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

NOTICE:
·

Never directly apply battery voltage to the solenoid valve connector (Do not allow a current of 1 A or more to flow). Perform the operation check via the specified bulb (resistance).

·

If a current of 1 A or more flows, the characteristic of the solenoid valve changes.

OK:

The solenoid valve makes an operating sound.


Result:
proceed to
OK
NG






OK

NG