Home › Drivetrain › A4Q AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › 2011.11–2015.08
RM19Y0E _52 Drivetrain _002983 A4Q AUTOMATIC TRANSMISSION / TRANSAXLE _0015077 AUTOMATIC TRANSMISSION SYSTEM D

A4Q AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  ROAD TEST  


PROBLEM SYMPTOM CONFIRMATION


a.

Based on the result of the customer problem analysis, try to reproduce the symptoms. If the problem is that the transmission does not shift up, shift down, or the shift point is too high or too low, conduct the following road test referring to the automatic shift schedule and simulate the problem symptoms.



PERFORM ROAD TEST


NOTICE:

Perform the test at the ATF (Automatic Transmission Fluid) temperature 70 to 90 °C (158 to 194 °F) in the normal operation.


a.

D position test

Move the shift lever to D, fully depress the accelerator pedal and check the following points.

i.

Check up-shift operation.

Check that 1st to 2nd, 2nd to 3rd and 3rd to 4th up-shifts take place, and that the shift points conform to the automatic shift schedule (See page General>SPECIFICATIONS>A4Q AUTOMATIC TRANSMISSION / TRANSAXLE>SERVICE DATA).

HINT:

4th Gear Up-shift Prohibition Control

·

ATF temperature is 10 °C (50 °F) or less.

·

Vehicle speed is 43 km/h (27 mph) or less.


4th Gear Lock-up Prohibition Control

·

ATF temperature is 20 °C (68 °F) or less.

·

Vehicle speed is 67 km/h (42 mph) or less.

·

Accelerator pedal is released.




ii.

Check for shift shock and slippage.

Check for shock and slippage when up-shifting from 1st to 2nd, 2nd to 3rd and 3rd to 4th.


iii.

Check for abnormal noises and vibration.

Check for abnormal noise and vibration when up-shifting from 1st to 2nd, 2nd to 3rd and 3rd to 4th while driving with the shift lever in D, and also check while driving in the lock-up condition.

HINT:

The cause of abnormal noises and vibration must be checked very thoroughly as it could also cause loss of balance in parts, such as the differential and torque converter assembly, etc.



iv.

Check kick-down operation.

Check the possible kick-down vehicle speeds when the 2nd to 1st, 3rd to 2nd and 4th to 3rd kick-downs take place while driving with the shift lever in D. Confirm that each takes place within the applicable vehicle speed range indicated in the automatic shift schedule (See page General>SPECIFICATIONS>A4Q AUTOMATIC TRANSMISSION / TRANSAXLE>SERVICE DATA).


v.

Check for abnormal shock and slippage during kick-down.


vi.

Check the lock-up mechanism.

·

Drive in D (4th gear) at a constant speed (lock-up ON).

·

Lightly depress the accelerator pedal and check that the engine speed does not change abruptly.


HINT:

If there is a sudden increase in engine speed, lock-up has not occurred.




b.

3 position test

Move the shift lever to 3, fully depress the accelerator pedal and check the following points.

i.

Check the transmission control switch operation.

While driving in D (4th gear), move the shift lever to 3, and check that the 4th to 3rd down-shift takes place.


ii.

Check up-shift operation.

Check that the 1st to 2nd and 2nd to 3rd up-shift take place and that the shift points conforms to the automatic shift schedule (See page General>SPECIFICATIONS>A4Q AUTOMATIC TRANSMISSION / TRANSAXLE>SERVICE DATA).

HINT:

There is no 3rd to 4th up-shift in 3.

3rd Gear Up-shift Prohibition Control

·

ATF temperature is -10 °C (14 °F) or less.

·

Vehicle speed is 26 km/h (16 mph) or less.




iii.

Check engine braking.

While driving in 3 and 3rd gear, release the accelerator pedal and check the engine braking effect.



c.

2 position test

Move the shift lever to 2 and fully depress the accelerator pedal and check the following points.

i.

Check up-shift operation.

Check that the 1st to 2nd up-shift takes place and that the shift point conforms to the automatic shift schedule (See page General>SPECIFICATIONS>A4Q AUTOMATIC TRANSMISSION / TRANSAXLE>SERVICE DATA).

HINT:

There is no 3rd up-shift and lock-up function in 2.



ii.

Check engine braking.

While driving in 2 and 2nd gear, release the accelerator pedal and check the engine braking effect.


iii.

Check for abnormal noises during acceleration and deceleration, and for shock during up-shift and down-shift.



d.

L position test

Move the shift lever to L, fully depress the accelerator pedal and check the following points.

i.

Check that no up-shift takes place.

While driving in L, check that there is no up-shift to 2nd gear.

HINT:

There is no lock-up function in L.



ii.

Check engine braking.

While driving in L, release the accelerator pedal and check the engine braking effect.


iii.

Check for abnormal noises during acceleration and deceleration.



e.

R position test

Move the shift lever to R, lightly depress the accelerator pedal, and check that the vehicle moves backward without any abnormal noise or vibration.

CAUTION:

Before conducting this test, ensure that the test area is free from people and obstructions.



f.

P position test

Stop the vehicle on a slope (more than 5°), move the shift lever to P and release the parking brake. Check that the vehicle does not move.