Home › Drivetrain › A4Q AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › 2011.11–2015.08
RM19Y0E _52 Drivetrain _002983 A4Q AUTOMATIC TRANSMISSION / TRANSAXLE _0015077 AUTOMATIC TRANSMISSION SYSTEM U

A4Q AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the Data List displayed by the intelligent tester, you can read the values of the switches, sensors, actuators and so on without parts removal. Reading the Data List as the first step of troubleshooting is one method of shortening labor time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the tester on.


f.

Enter the following menus: Powertrain / ECT / Data List.


g.

In accordance with the display on the tester, read the Data List.

Powertrain > ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Speed Engine speed 0 to 10200 rpm 700 to 800 rpm: idle after engine warmed-up -
SPD(NT) Input turbine speed 0 to 10200 rpm
HINT:
·

Lock-up ON (After warming up the engine);

Input turbine speed equal to the engine speed.

·

Lock-up OFF (Idling at shift lever in N);

Input turbine speed nearly equal to the engine speed.



-
SPD(NO) Output shaft speed 0 to 10200 rpm
HINT:

3rd when the shift lever in D (After warming up the engine);

Output shaft speed becomes close to the input turbine speed


-
Vehicle Speed Vehicle speed 0 to 255 km/h Same as speedometer indication -
Throttle POS Throttle position (TP) 0 to 100 %
·

0 to 5 %: Throttle fully closed

·

95 to 100 %: Throttle fully open


-
Battery Voltage Battery voltage 0 to 25.5 V Idling:
11 to 14 V
-
Stop Light Switch Stop light SW status ON or OFF
·

Brake pedal is depressed: ON

·

Brake pedal is released: OFF


-
A/T Oil Temperature 1 ATF Temperature sensor value min.: -50°C (-58°F)
max.: 205°C (401°F)
·

After Stall Test; Approximately 80 to 100°C(176 to 212°F)

·

Equal to ambient temperature when the engine is cold


If the value is "-50°C (-58°F)" or "205°C (401°F)", ATF temperature sensor circuit is opened or shorted.
SL1 Solenoid Status Shift solenoid SL1 status 0 to 2550 mA Shift solenoid valve SL1 is;
ON → OFF: 1000 → 0 mA *1
-
SL2 Solenoid Status Shift solenoid SL2 status 0 to 2550 mA Shift solenoid valve SL2 is;
ON → OFF: 1000 → 0 mA *1
-
SL3 Solenoid Status Shift solenoid SL3 status 0 to 2550 mA Shift solenoid valve SL3 is;
ON → OFF: 1000 → 0 mA *1
-
DSU Solenoid Status Shift solenoid DSU status 0 to 100 % Shift solenoid valve DSU is;
ON → OFF: 100 → 0 %
-
Lock Up Solenoid Status Shift solenoid SL status ON or OFF
·

Lock-up: ON

·

Except Lock-up: OFF


-
SR Solenoid Status Shift solenoid SR status ON or OFF
·

1st (shift lever in L) and 2nd gears: ON

·

3rd and 4th gears: OFF


-
Shift SW Status(P) PNP SW status ON or OFF ON: Shift lever in P
OFF: Shift lever not in P
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch, transmission control switch or the shift cable may be incorrect.
(*2)
Shift SW Status(R) PNP SW status ON or OFF ON: Shift lever in R
OFF: Shift lever not in R
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch, transmission control switch or the shift cable may be incorrect.
(*2)
Shift SW Status(N) PNP SW status ON or OFF ON: Shift lever in N
OFF: Shift lever not in N
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch, transmission control switch or the shift cable may be incorrect.
(*2)
Shift SW Status(D) PNP SW status ON or OFF ON: Shift lever in D
OFF: Shift lever not in D
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch, transmission control switch or the shift cable may be incorrect.
(*2)
Shift SW Status(3) PNP SW status ON or OFF ON: Shift lever in 3
OFF: Shift lever not in 3
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch, transmission control switch or the shift cable may be incorrect.
(*2)
Shift SW Status(2) PNP SW status ON or OFF ON: Shift lever in 2
OFF: Shift lever not in 2
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch, transmission control switch or the shift cable may be incorrect.
(*2)
Shift SW Status(L) PNP SW status ON or OFF ON: Shift lever in L
OFF: Shift lever not in L
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch, transmission control switch or the shift cable may be incorrect.
(*2)
Shift Status TCM gearshift command N, 1st, 2nd, 3rd, 3rd LU, 4th, 4th LU Shift lever in;
·

N: Neutral

·

R: Reverse

·

L: 1st

·

2: 1st or 2nd

·

3: 1st, 2nd or 3rd

·

D : 1st, 2nd, 3rd or 4th


-
HINT:
·

*1: The value may exceed 1000 mA due to the current feedback.

·

*2: When the failure still occurs even after adjusting these parts.

Click hereDrivetrain>A4Q AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>P0705





ACTIVE TEST


HINT:

Performing the Active Test using the intelligent tester allows the relay, VSV, actuator and so on to operate without parts removal. Performing the Active Test as the first step of troubleshooting is one method to shorten labor time.

It is possible to display the Data List during the Active Test.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the tester on.


f.

Enter the following menus: Powertrain / ECT / Active Test.


g.

In accordance with the display on the tester, perform the Active Test.

Powertrain > ECT > Active Test
Tester Display Measurement Item Control Range
Control the SL1 Solenoid [Test Details]
Operate the shift solenoid valve SL1.
[Vehicle Condition]
·

Ignition switch ON

·

Shift lever in P

·

Vehicle stopped

·

Engine stopped

·

Throttle fully closed


Possible to check the SL1 operation.
Control the SL2 Solenoid [Test Details]
Operate the shift solenoid valve SL2.
[Vehicle Condition]
·

Ignition switch ON

·

Shift lever in P

·

Vehicle stopped

·

Engine stopped

·

Throttle fully closed


Possible to check the SL2 operation.
Control the SL3 Solenoid [Test Details]
Operate the shift solenoid valve SL3.
[Vehicle Condition]
·

Ignition switch ON

·

Shift lever in P

·

Vehicle stopped

·

Engine stopped

·

Throttle fully closed


Possible to check the SL3 operation.
Control the DSU Solenoid [Test Details]
Operate the shift solenoid valve DSU.
[Vehicle Condition]
·

Ignition switch ON

·

Shift lever in P

·

Vehicle stopped

·

Engine stopped

·

Throttle fully closed


Possible to check the DSU operation.
Control the SL Solenoid [Test Details]
Operate the shift solenoid valve SL.
[Vehicle Condition]
·

Ignition switch ON

·

Shift lever in P

·

Vehicle stopped

·

Engine stopped

·

Throttle fully closed


Possible to check the SL operation.
Control the SR Solenoid [Test Details]
Operate the shift solenoid valve SR.
[Vehicle Condition]
·

Ignition switch ON

·

Shift lever in P

·

Vehicle stopped

·

Engine stopped

·

Throttle fully closed


Possible to check the SR operation.